CHIEF MSP-BBSP Bedienungsanleitung
Installation Instructions MSP-BBSP
1
IMPORTANT WARNINGS AND PRECAUTIONS!
WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.
CAUTION: ACAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corre-
sponding instructions.
•WARNING:Improper installation can result in serious personal injury! Make sure that the structural members can
support a redundant weight factor five times the total weight of the equipment: if not, reinforce the struc-
ture before installing the mount.
•WARNING:Be aware also of the potential for personal injury or damage to the unit if it is not adequately mounted.
•WARNING:The installer is responsible for verifying that the wall to which the mount is anchored will safely support
the combined load of all attached components or other equipment.
•WARNING:The weight of the display placed on the mountmust not exceed 40 lbs. (18.1 kg), the maximum load capac-
ity of the mount.
•WARNING:Watch for pinch points. Do not put your fingers between movable parts.
•WARNING:Make sure the mount and brackets are correctly oriented.
•CAUTION: Check the unit for shipping damage before you begin the installation.
CONTENTS
SPECIFICATIONS ....................................................1
TOOLS REQUIRED FOR INSTALLATION ..............1
DRAWINGS ..............................................................2
INSPECT THE UNIT BEFORE INSTALLING ...........3
iC-SP-TP1-01 INSTALLATION .................................3
ADJUSTMENTS .......................................................5
ADJUSTMENTS .......................................................5
SPECIFICATIONS
This mount accommodates all VESA® 75mm/100mm compli-
ant displays. Table 1 provides mount specifications.
TOOLS REQUIRED FOR
INSTALLATION
• Electric drill and bit set
• Phillips Screwdriver
• Level
NOTE: Other tools may be required depending on the
mounting surface and method of installation.
Table 1: Specifications
Depth from Wall 3.34” (84.74mm)deep in the closed
position
Dimensions (WxHxD) 2-3/8”x 5-11/16” x 1-13/16”
(61 x 145 x 46 mm)
Tilt +/-15 degrees
Pivot 180 degrees
Weight Capacity 40 lbs. (18.2 kg)
2
Installation Instructions MSP-BBSP
DRAWINGS
#10 Wood Screws
Wall Plate
M4 X 8mm, 12mm, 16mm, 20mm or 30mm Phillips pan head screws
1/8” Spacers
(optional)
Adjustment Knob
End Cap
End Cap
Set Screw
Tension Adjustment Bolt
Installation Instructions MSP-BBSP
3
INSPECT THE UNIT BEFORE INSTALLING
WARNING: Watch for pinch points. Do not put your fingers
between movable parts.
1. Carefully inspect the mount for shipping damage. If any dam-
age is apparent, call your carrier claims agent and do not con-
tinue with the installation until the carrier has reviewed the
damage.
NOTE: Read all instructions before starting installation.
2. Lay out components to ensure you have all the required parts
before proceeding (see drawing on page 2).
INSTALLATION
WARNING: It is the responsibility of the installer to verify that
the structure to which the mount is anchored will
safety support five times the combined load of all
attached components and equipment.
1. Determine the exact mounting location prior to installation,
considering the unit’s swing radius.
2. Using the wall plate as a template, drill two 3/32” pilot holes to
a minimum depth of 1 1/2” into wall stud.
3. Using two Phillips head #10 wood screws (supplied), secure
the wall plate (see Figure 1).
4. Install screw cover (see Figure 2).
5. Check mount to insure it is level and adjust to level if neces-
sary.
6. Determine if you are installing a VESA compliant flush mount
display, VESA compliant recessed mount display or a non-
VESA compliant display and follow the appropriate instruc-
tions.
VESA Compliant Flush Mounting
A. Install the mount on the wall plate, set to desired height at
one of the fixed height settings and secure by tightening
the set screw (see Figure 3).
B. Install the end caps on the wall plate (see Figure 4).
CAUTION: If monitor uses a screw size other than M4, DO NOT
use the M4 screws provided. Using the wrong screws
could result in damage to your display.
C. Start two M4 X 12mm Phillips pan head screws in the top
mounting holes of your display.
D. Matching the hole pattern on your display with the hole
pattern on the mount (see Figure 5), hang the mount from
the two screws started in Step A.
Figure 1. Secure Wall Plate
Figure 2. Install Screw Cover
Figure 3. Install iC-SP-TP1
and Tighten Set Screw
Fixed Height Settings
Set Screw
Figure 4. Install End Caps
4
Installation Instructions MSP-BBSP
E. Install two remaining Phillips pan head screws through the
mount and into the mounting holes of your display.
F. Secure your display to the mount by tightening the four
Phillips pan head screws.
WARNING: Make sure your cables do not run through a pinch
point.
G. Connect and secure power/audio/video cables, making
sure to leave sufficient slack to allow for movement of the
display.
VESA Compliant Recessed Mounting
A. Place four 1/2” X 3/8” Nylon spacers or four 1/2” X 3/4”
Nylon spacers, as necessary, over the mounting holes of
your display (see Figure 6).
B. Place the mount over the Nylon spacers, matching the hole
pattern on your display (75mm or 100mm) with the hole
pattern on the mount.
C. Using four M4 X 20mm Phillips pan head screws for 1/2”
X 3/8” Nylon spacer installation or four M4 X .7 X 30mm
Phillips pan head screws for the 1/2” X 3/4” Nylon spacer
installation, secure the mount to your display.
H. Install the mount on the wall plate, set to desired height at
one of the fixed height settings and secure by tightening
the set screw (see Figure 3).
J. Install the end caps on the wall plate (see Figure 4).
WARNING: Make sure your cables do not run through a pinch
point.
K. Connect and secure power/audio/video cables, making
sure to leave sufficient slack to allow for movement of the
display.
Non-VESA Compliant Mounts
A. Contact Chief Manufacturing for custom interface brack-
ets.
Figure 5. Flush Mounting
Figure 6. Recessed Mounting
Installation Instructions MSP-BBSP
5
INSTALLATION (200mm x 100MM)
Attach Interface Adapter to Display
1. Select six M4 X 16mm Phillips flat head screws and six
1/8” nylon retaining spacers.
2. Place display face down on a clean dry surface.
3. Align six 1/8” nylon spacers over mounting holes in dis-
play back (see Figure 7).
4. Align interface bracket mounting holes with 1/8” nylon
spacers.
5. Install six M4 X 16mm Phillips flat head screws through
six mounting holes in interface bracket, spacers and into
display (see figure 7).
6. Tighten six M4 X 16mm Phillips flat head screws.
Attach Centris Bracket to Display
1. Start two M4 x 8mm Phillips pan head screws into the top
two mounting holes of interface bracket (see figure 8).
2. Hang mount from two screws.
3. Install the remaining two M4 x 8mm Phillips pan head
screws into the bottom two mounting holes of interface
bracket.
4. Secure the display to the mount (Centris bracket) by tight-
ening four M4 x 8mm Phillips pan head screws.
Interface Bracket
M4 X 16mm
Phillips Flat Head Screws (6)
1/8” Nylon Spacers (6) Display
Figure 7. Install Interface Bracket
Interface Bracket
M4 X 8mm
Phillips Pan Head Screws (4)
Display
Centris Bracket
Figure 8. Attach Centris Bracket to Display
6
Installation Instructions MSP-BBSP
ADJUSTMENTS
CAUTION: Overtightening adjustment will cause excessive wear.
Rotational Tilt, Pitch, and Roll Adjustment
1. If necessary, use a Phillips screwdriver to tighten or loosen
the Phillips pan head screw (see DRAWINGS).
2. Check for desired tension.
3. Repeat Steps 1 and 2 until desired tension is obtained.
Lateral Tension Adjustment
1. Using a 3/16” hex wrench (provided), slightly tighten or
loosen lateral tension adjustment bolt (see DRAWINGS).
2. Check for desired tension.
3. Repeat Steps 1 and 2 until desired tension is obtained.
©2005 Chief Manufacturing Inc. All rights reserved.
Patents and patents pending. 8/05
8832-000089 (Rev. A)
Chief Manufacturing Inc.
8401 Eagle Creek Parkway, Suite 700 CSAV Europe B.V.
Savage, MN 55378, USA Zekeringstraat 17, 1014 BM
PHONE: 800.582.6480 Amsterdam, Netherlands
PHONE: 952.277.3901 PHONE: 31 (0)20 5708923
FAX: 952.894.6918 FAX: 31 020 5708989
www.chiefmfg.com
Inhaltsverzeichnis
Andere CHIEF Rack & Stand Handbücher
CHIEF
CHIEF WM-100 Bedienungsanleitung
CHIEF
CHIEF UPM-2401 Bedienungsanleitung
CHIEF
CHIEF Vibration Mount CMA-347 Bedienungsanleitung
CHIEF
CHIEF Truss Pitch-Adjustable Mount TPP Bedienungsanleitung
CHIEF
CHIEF TPS Series Bedienungsanleitung
CHIEF
CHIEF MTMP1U Bedienungsanleitung
CHIEF
CHIEF CM6DHXX-T Benutzerhandbuch
CHIEF
CHIEF JWDIW Bedienungsanleitung
CHIEF
CHIEF PAC-Y3 Bedienungsanleitung
CHIEF
CHIEF FCA4U Bedienungsanleitung
CHIEF
CHIEF MSP-WRTIDSKY1 Bedienungsanleitung
CHIEF
CHIEF Phoenix 20 Series Bedienungsanleitung
CHIEF
CHIEF FSA-1015 Bedienungsanleitung
CHIEF
CHIEF LCB1UP Bedienungsanleitung
CHIEF
CHIEF KTP Series Bedienungsanleitung
CHIEF
CHIEF CPA116 Bedienungsanleitung
CHIEF
CHIEF 25MWR Service-Handbuch
CHIEF
CHIEF PSMH2485 Bedienungsanleitung
CHIEF
CHIEF PSMH-2046 Bedienungsanleitung
CHIEF
CHIEF SLBU Bedienungsanleitung
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
