CHIEF PAC790 Bedienungsanleitung

INSTALLATION INSTRUCTIONS

Swivel Accessory for Carts and Stands

PAC790

PAC790 Installation Instructions

DISCLAIMER

Milestone AV Technologies, and its affiliated corporations and

subsidiaries (collectively, "Milestone"), intend to make this

manual accurate and complete. However, Milestone makes no

claim that the information contained herein covers all details,

conditions or variations, nor does it provide for every possible

contingency in connection with the installation or use of this

product. The information contained in this document is subject

to change without notice or obligation of any kind. Milestone

makes no representation of warranty, expressed or implied,

regarding the information contained herein. Milestone assumes

no responsibility for accuracy, completeness or sufficiency of

the information contained in this document.

Chief® and ClickConnect™ are registered trademarks of

IMPORTANT WARNINGS AND

CAUTIONS!

WARNING:

A WARNING alerts you to the possibility of

serious injury or death if you do not follow the instructions.

CAUTION:

A CAUTION alerts you to the possibility of

damage or destruction of equipment if you do not follow the

corresponding instructions.

WARNING:

Failure to read, thoroughly understand, and

follow all instructions can result in serious personal injury,

damage to equipment, or voiding of factory warranty! It is the

installer’s responsibility to make sure all components are

properly assembled and installed using the instructions

provided.

WARNING:

Failure to provide adequate structural strength

for this component can result in serious personal injury or

damage to equipment! It is the installer’s responsibility to

make sure the structure to which this component is attached

can support five times the combined weight of all equipment.

Reinforce the structure as required before installing the

component.

WARNING:

Exceeding the weight capacity can result in

serious personal injury or damage to equipment! It is the

installer’s responsibility to make sure the combined weight of

all components mounted on the accessory does not exceed

200 lbs (90.72 kg) or the specific weight limit of the cart or

stand that it is mounted to.

DIMENSIONS

14.00

355.6

14.00

355.6

3.20

81.3

2.95

4.01

101.8

4.67

118.5

2.03

51.6

15° MAX SWIVEL ANGLE

Installation Instructions PAC790

LEGEND

Tighten Fastener

Apretar elemento de fijación

Befestigungsteil festziehen

Apertar fixador

Serrare il fissaggio

Bevestiging vastdraaien

Serrez les fixations

Loosen Fastener

Aflojar elemento de fijación

Befestigungsteil lösen

Desapertar fixador

Allentare il fissaggio

Bevestiging losdraaien

Desserrez les fixations

Phillips Screwdriver

Destornillador Phillips

Kreuzschlitzschraubendreher

Chave de fendas Phillips

Cacciavite a stella

Kruiskopschroevendraaier

Tournevis à pointe cruciforme

Open-Ended Wrench

Llave de boca

Gabelschlüssel

Chave de bocas

Chiave a punte aperte

Steeksleutel

Clé à fourche

By Hand

A mano

Von Hand

Com a mão

A mano

Met de hand

À la main

Hex-Head Wrench

Llave de cabeza hexagonal

Sechskantschlüssel

Chave de cabeça sextavada

Chiave esagonale

Zeskantsleutel

Clé à tête hexagonale

Pencil Mark

Marcar con lápiz

Stiftmarkierung

Marcar com lápis

Segno a matita

Potloodmerkteken

Marquage au crayon

Drill Hole

Perforar

Bohrloch

Fazer furo

Praticare un foro

Gat boren

Percez un trou

Adjust

Ajustar

Einstellen

Ajustar

Regolare

Afstellen

Ajuster

Remove

Quitar

Entfernen

Remover

Rimuovere

Verwijderen

Retirez

Optional

Opcional

Optional

Opcional

Opzionale

Optie

En option

Security Wrench

Llave de seguridad

Sicherheitsschlüssel

Chave de segurança

Chiave di sicurezza

Veiligheidssleutel

Clé de sécurité

Installation Instructions PAC790

TOOLS REQUIRED FOR INSTALLATION

PARTS

3/16"

(included)

A (1

[swivel accessory]

B(4)

5/16-18 x 5/8"

C(1)

3/16"

Installation Instructions PAC790

ASSEMBLY

Attaching Head to Cart/Stand Assembly

IMPORTANT ! : When attaching head assembly ensure

that the ClickConnect lock is at TOP of head assembly.

(See Figure 1)

1. Slide swivel accessory (A) into the cart/stand assembly.

(See Figure 1)

2. Attach swivel accessory to cart/stand using four 5/16-18 x

3/8" button head cap screws (B). (See Figure 1)

Figure 1

Attaching Display to Accessory

WARNING:

EXCEEDING MAXIMUM WEIGHT CAPACITY

MAY LEAD TO SERIOUS PERSONAL INJURY OR

DAMAGE TO EQUIPMENT! It is the installer’s responsibility

to make sure the combined weight of all components

mounted on the accessory does not exceed 200 lbs (90.72

kg) or the specific weight limit of the cart or stand that it is

mounted to.

WARNING:

Before attaching display(s) to the cart/stand

ensure the cart/stand is on level surface.

CAUTION:

ALWAYS remove the display(s) BEFORE

adjusting the height of the cart/stand.

1. Attach PSBU or MSBU interface bracket(s) to the display(s)

following the instructions included with the bracket.

2. While supporting both sides of display, align four mounting

buttons on display or interface bracket with four mounting

holes in head assembly. (See Figure 2)

Figure 2

WARNING:

DISPLAY MAY WEIGH IN EXCESS OF 40

LBS! Always use two people and proper lifting techniques

when installing or positioning display on stand.

3. Lower display into place listening for audible "click" to

ensure recessed area of mounting buttons are properly

seated in lower area of mounting holes.

WARNING:

IMPROPER INSTALLATION CAN LEAD TO

STAND OR DISPLAY FALLING CAUSING SERIOUS

PERSONAL INJURY OR DAMAGE TO EQUIPMENT!

Ensure mounting buttons are completely engaged in

mounting holes.

NOTE:

Holes are provided in the faceplate for use with a

padlock or similar locking device,ifdesired.Inaddition,

the pin and nut may be removed from the upper holes

and moved to the lower holes for use as a more

permanent locking device. (See Figure 3)

(A)

(B) x 4

(Back view of cart/stand)

ClickConnect

lock at TOP of

head assembly

cart/stand

assembly

PAC790 Installation Instructions

Figure 3

Tilting Display

The display can be tilted up to 15

either backward or forward

from a straight upright position.

1. Turn knob counterclockwise on back of head assembly to

loosen the tilt. (See Figure 4)

Figure 4

2. Tilt display as desired, to a maximum of 15

either forward

or backward.

3. Turn knob clockwise to tighten display on head assembly.

(See Figure 4)

CAUTION:

Tighten knob on back of head assembly to

prevent damage to the stand.

4. If leaving the display in a straight upright position, it is

recommended that a bolt (not provided) be placed through

the head assembly (See Figure 4) to lock the display into

the upright position.

Swivelling Display

The display can be swivelled up to 15° either left or right from a

straight upright position.

1. Swivel display to the left or right up to 15° until desired

position is reached. (See Figure 5)

2. If leaving display in straight position, it is recommended that

a bolt (not provided) be placed through the hole on the

swivel device to lock the display into that position. (See

Figure 5)

Figure 5

Removing Display

1. Remove bolt or padlock from faceplate (if used).

NOTE:

The pin may have been used as a more permanent

locking device. If so, remove nut and pin and move

from the lower holes to the upper holes.

2. Pull back on flag on upper mounting hole and press pin

down into "Open" position.(See Figure 6)

WARNING:

DISPLAY MAY WEIGH IN EXCESS OF 40

LBS! Always use two people and proper lifting techniques

when installing or positioning display on cart/stand.

3. Carefully lift display from cart/stand.

4. Lift up on pin and place flag back against faceplate to return

it to "Closed" position. (See Figure 6)

Remove pin

and nut and

move to lower holes

A padlock or bolt may

be placed through latch

holes

Place optional bolt

(not provided) here

to lock in an upright

position.

Place optional bolt

(not provided) here

to lock in straight position.

Installation Instructions PAC790

Figure 6

Remove bolt

or padlock

if used

Pin in

"Open"

position -

Pin in

"Closed"

position -

move to

"Open"

position to

move to

"Closed"

position

remove

display

after display

is removed.

PAC790 Installation Instructions

Chief Manufacturing, a products division

of Milestone AV Technologies

8807-002001 Rev 00

Duchossois Group Company

www.chiefmfg.com

05/09

USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378

P800.582.6480 / 952.894.6280

F877.894.6918 / 952.894.6918

Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands

P+31 (0)40 2668620

F+31 (0)40 2668615

Asia Pacific A Room 24F, Block D, Lily YinDu International Building

LuoGang, BuJi Town, Shenzhen, CHINA.

P+86-755-8996 9226

F+86-755-8996 9217

Inhaltsverzeichnis

Andere CHIEF Rack & Stand Handbücher

CHIEF

CHIEF PAC516 Bedienungsanleitung

CHIEF

CHIEF MTTU Bedienungsanleitung

CHIEF

CHIEF SSB-265 Bedienungsanleitung

CHIEF

CHIEF WM210S Bedienungsanleitung

CHIEF

CHIEF KWT110 Bedienungsanleitung

CHIEF

CHIEF SSB-083 Bedienungsanleitung

CHIEF

CHIEF QMP1T Bedienungsanleitung

CHIEF

CHIEF Dual Stud Wall Arm CTA-225 Bedienungsanleitung

CHIEF

CHIEF Wall Mount PDWP MB 40 P Bedienungsanleitung

CHIEF

CHIEF Phoenix 20 Series Bedienungsanleitung

CHIEF

CHIEF FCD100 Bedienungsanleitung

CHIEF

CHIEF AA Series Bedienungsanleitung

CHIEF

CHIEF STS1 Bedienungsanleitung

CHIEF

CHIEF PSS2000 Bedienungsanleitung

CHIEF

CHIEF SSB-202 Bedienungsanleitung

CHIEF

CHIEF CSMP9X12 Bedienungsanleitung

CHIEF

CHIEF MSP-DCCUST1 Bedienungsanleitung

CHIEF

CHIEF AVSFSS Bedienungsanleitung

CHIEF

CHIEF FCAC06B Bedienungsanleitung

CHIEF

CHIEF LWM2X1UP Bedienungsanleitung

CHIEF

CHIEF OFB214 Bedienungsanleitung

CHIEF

CHIEF MSP-WL4C Bedienungsanleitung

CHIEF

CHIEF CMA395 Bedienungsanleitung

CHIEF

CHIEF ESS-42 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung