Cisco Physical Access CIAC-GW-K9 Bedienungsanleitung

CHAPTER

2-1

Cisco Physical Access Gateway User Guide

OL-32499-01

Installing and Configuring the Cisco Physical

Access Gateway

Contents

This chapter includes the following information:

•Overview, page 2-2

•Package Contents, page 2-3

•Physical Overview and Port Description, page 2-3

•Installing the Cisco Physical Access Gateway, page 2-7

•Configuring and Managing the Gateway Using a Direct Connection, page 2-15

–

Understanding Network Time Protocol (NTP) Settings, page 2-15

–

Connecting a PC to the Gateway, page 2-16

–

Entering the Gateway Network Settings, page 2-17

–

Changing the User Password, page 2-19

–

Upgrading the Gateway Firmware Using a Direct Connection, page 2-20

–

Displaying Serial Numbers and Other Information, page 2-23

•Configuring the Gateway Using the Cisco Physical Access Manager, page 2-24

•Resetting the Cisco Physical Access Gateway, page 2-25

2-2

Cisco Physical Access Gateway User Guide

OL-32499-01

Chapter 2 Installing and Configuring the Cisco Physical Access Gateway

Overview

The Cisco Physical Access Gateway (Figure 2-1) is installed near each door to provide access control

and connections for card readers, door locks and other input and output devices. The Gateway is

connected to the Cisco Physical Access Manager using an Ethernet connection to the IP network. Power

is supplied through a Power over Ethernet (PoE) connection, or using a DC power source. Each Gateway

includes connections for up to two Wiegand door readers, three input devices, and three output devices.

Optional expansion modules are available to add additional doors and devices to the Gateway.

Figure 2-1 Cisco Physical Access Gateway

2-3

Cisco Physical Access Gateway User Guide

OL-32499-01

Chapter 2 Installing and Configuring the Cisco Physical Access Gateway

Package Contents

Each Cisco Physical Access Gateway includes the following:

•Six End-Of-Line (EOL) 1K termination resistors (used for supervised input interfaces)

•Two mounting brackets, with 4 screws for each bracket

•Regulatory compliance and safety information

•Quick Start guide

•Connector plugs, including the following:

Physical Overview and Port Description

Figure 2-2 and Figure 2-3 show the location of each port, including connections for power, Ethernet,

door readers and other input and output devices.

Figure 2-2 Cisco Physical Access Gateway Ports and Connectors: Side View

Type Quantity

10 Pin 1

3 Pin 4

2 Pin 6

187040

2-4

Cisco Physical Access Gateway User Guide

OL-32499-01

Chapter 2 Installing and Configuring the Cisco Physical Access Gateway

Physical Overview and Port Description

Figure 2-3 Cisco Physical Access Gateway Ports and Connectors: Top View

1Power—Two-pin connector for Voltage In (VIN) and Ground (GND) to connect a 12 to 24 VDC

external power source.

2CAN—A three-wire CAN bus is used to connect additional modules, including the Cisco Reader

Module, Cisco Input Module, and Cisco Output Module.

Note Modules are connected using the CAN1 interface. The CAN2 interface is not supported

in this release.

3SVR (Server)—When the LED is steady green, the Gateway is connected to a Cisco PAM

appliance.

4Fast Ethernet interfaces—There are two 10/100 BASE-TX RJ-45 connectors:

•ETH 0: connects the Gateway to the network. ETH 0 also supports Power over Ethernet

(PoE) for the device (optional).

•ETH 1: connects the device to a PC to access the device configuration web page.

5Serial interface—The RS-485 interface is not supported in this release.

6Wiegand interface—This interface can be configured as the following:

•One 10-pin Wiegand/clock and data reader interface to connect a single door reader.

•Two 5-pin Wiegand/clock and data interfaces to connect two door readers (for installations

where a 5-pin interface is sufficient).

Note Disconnect power from the Gateway or Reader module before connecting reader devices

to the modules. Connecting a reader device when the modules are powered can cause the

Gateway or Reader module to malfunction.

2 5 6 7 8 9 10

187039

2-5

Cisco Physical Access Gateway User Guide

OL-32499-01

Chapter 2 Installing and Configuring the Cisco Physical Access Gateway

Physical Overview and Port Description

LED Status

Table 2-1 describes the Gateway module status LEDs:

7Input interfaces—Three input interfaces used to sense the contact closure. Each input can be

configured as supervised or unsupervised and can be configured to sense a Normally Open (NO)

or Normally Closed (NC) contact.

•An unsupervised input senses a simple contact closure state, including Normal or Alarm.

When connected to open contacts, the terminal voltage range is 4V to 5V. For closed

contacts, the voltage range is 0V to 0.7V.

•A supervised input senses four contact states, including Normal, Alarm, Open and Short.

These inputs require 1K End-Of-Line (EOL) termination resistors installed at the contacts

(two resistors are included in the accessory kits for each Input port).

8Output interfaces—Three Form C (5A @ 30V) relay output interfaces. Each output connection

can be configured as either Normally Closed (NC) or Normally Open (NO).

•C & NO connection: The relay is normally open. The circuit is closed when triggered.

•C & NC connection: The relay is normally closed. The circuit is opened when triggered.

Notes:

•Install surge protection between the output device and the Cisco PAM module, as described

in the “Installing Surge Suppressors on Output Device Connections” section on page 1-13.

•Common (C) is always used, and either NC or NO is used to complete the connection.

•All Generic Output devices installed in Cisco PAM systems prior to release 1.1.0, were

connected to the Gateway, Reader, or Output modules with the wiring reversed. If upgrading

to Cisco PAM release 1.1.0 from an earlier release, disconnect all Generic Output devices

and do the following:

–

Connect Normally Open devices to the N.O. and C connectors on the Gateway, Reader,

or Output module.

–

Connect Normally Closed devices to the N.C. and C connectors on the Gateway, Reader,

or Output module.

9PF—Power fail input: an unsupervised input that raises a “power fail” alarm when the circuit is

open. Can be configured as an additional unsupervised port. An unsupervised input indicates

only normal or alarm. The corresponding LED is red when circuit is open (when no input is

connected).

10 TM—Tamper input: an unsupervised input that raises a “tamper” alarm when the circuit is open.

Can be configured as an additional unsupervised port. An unsupervised input indicates only

normal or alarm. The corresponding LED is red when circuit is open (when no input is

connected).

11 Reset—Resets the device. See the “Resetting the Cisco Physical Access Gateway” section on

page 2-25 for more information.

Table 2-1 Gateway LEDs

Status Description

SVR

Steady Green The Gateway is connected to a Cisco PAM appliance.

2-6

Cisco Physical Access Gateway User Guide

OL-32499-01

Chapter 2 Installing and Configuring the Cisco Physical Access Gateway

Physical Overview and Port Description

Note Led Status does not work on 5 wire reader.

Input Port LEDs

OFF Input is not configured

GREEN Input is configured and in normal state

BLINKING GREEN Input is configured, and is receiving and alarm or other data.

BLINKING RED Input is configured, short

RED Input is configured, open

Output Port LEDs

Off Output not configured

Solid Green Output configured and in default state

Blinking Green Output configured and active

Table 2-1 Gateway LEDs (continued)

Status Description

2-7

Cisco Physical Access Gateway User Guide

OL-32499-01

Chapter 2 Installing and Configuring the Cisco Physical Access Gateway

Installing the Cisco Physical Access Gateway

•Before You Begin, page 2-7

•Procedure, page 2-7

Before You Begin

Before you install a Cisco Physical Access Gateway, verify the following:

•Verify that the module has access to a power source. See the “Power Options and Requirements”

section on page 1-12 for more information.

•Verify that you have the necessary mounting brackets or other hardware. See the “Mounting a

Gateway or Optional Module” section on page 1-14.

Procedure

To install the Cisco Physical Access Gateway, perform the following procedure:

Step 1 Mount the Gateway to a wall. See the “Mounting a Gateway or Optional Module” section on page 1-14

for more information.

Step 2 Connect the Gateway to a power source.

•If using a DC power source, insert a two-pin connector plug into the DC power port (Figure 2-4),

and connect the Voltage In (VIN) and ground (GND) wires.

•If using PoE, connect an Ethernet cable from the IP network to the ETH0 port (Figure 2-4).

See the “Power Options and Requirements” section on page 1-12 for more information.

2-8

Cisco Physical Access Gateway User Guide

OL-32499-01

Chapter 2 Installing and Configuring the Cisco Physical Access Gateway

Installing the Cisco Physical Access Gateway

Figure 2-4 Power Connections for the Cisco Physical Access Gateway

Step 3 Connect one or two door reader devices to the Wiegand interface using one of the following

configurations:

•Connect a single door reader using all 10 Wiegand interface pins.

•Connect one or two door readers using 5-pin Wiegand interface connections (for installations where

a 5-pin interface is sufficient).

1DC power GND (ground)— Connects the DC ground wire to the Gateway.

2DC power Voltage In (VIN)—Connects the DC Voltage In (VIN) wire to the Gateway.

3ETH0 for PoE—Connects the Ethernet cable from the Access Layer switch to the Gateway. To

use this power option, the switch must support PoE.

271594

2-9

Cisco Physical Access Gateway User Guide

OL-32499-01

Chapter 2 Installing and Configuring the Cisco Physical Access Gateway

Installing the Cisco Physical Access Gateway

Figure 2-5 shows the location of the Wiegand interface connections. The table describes the connections

for 10-pin and 5-pin reader interface connections. The wire connectors from the reader device are shown

in parentheses. If attaching a second reader, use the alternative connections shown in the column on the

far right.

Figure 2-5 Wiegand Interface on the Gateway and Reader Modules

Chassis

Label Description

One Reader

10 Wire Connection

First Reader in a

5 Wire Connection

Second Reader in a

5 Wire Connection

1PWR +12v PWR (red) 1PWR (red) PWR (red)

2GND Ground GND (black) GND (black) GND (black)

3D0 Data 0 D0 (green) D0 (green) ----------

4D1/CLCK Data 1 D1/CLCK (white) D1/CLCK (white) ----------

5DRTN Shield DRTN (shield) DRTN (shield) DRTN (shield)

6GRN Output

2GRN (orange) GRN (orange) ----------

7RED Output RED (brown) ---------- 3GRN (orange)

8BPR Output

(Beeper)

BPR (yellow)

(yellow)

---------- ----------

271603

2-10

Cisco Physical Access Gateway User Guide

OL-32499-01

Chapter 2 Installing and Configuring the Cisco Physical Access Gateway

Installing the Cisco Physical Access Gateway

Step 4 Connect input devices to the Gateway:

a. Insert two-pin connector plugs into the input ports (see Figure 2-7).

b. (Optional, for supervised input connections only). Install two End-Of-Line (EOL) 1K termination

resistors in each supervised input interface (one terminator in each connector). Figure 2-6 shows the

terminator installation for a Normally Closed (NC) and Normally Open (NO) input connection.

Figure 2-6 Input Connections: Cisco Physical Access Gateway,Input and Reader Modules

c. Connect the wires from the input devices (see Figure 2-7).

Note Each of the input connections can be configured as supervised or unsupervised. The tamper and

power fail inputs can be configured as additional unsupervised ports. A supervised input

supports four states: normal, alarm, open and short. An unsupervised input indicates only normal

or alarm.

9HCRD Hold

Control

HCRD (blue) ---------- D1/CLCK (white)

10 CP Card

Present

CP (purple) ---------- D0 (green)

1. Wire colors are shown in parentheses.

2. Outputs show the LED color and reader wire color (in parentheses). For example, “GRN (orange)” supports a green LED.

Attach the orange wire from the reader device.

3. ---------- means the wire slot is not used.

Chassis

Label Description

One Reader

10 Wire Connection

First Reader in a

5 Wire Connection

Second Reader in a

5 Wire Connection

1K,, 1%

187838

Inhaltsverzeichnis

Andere Cisco Tor Handbücher

Cisco

Cisco DPC2325 Bedienungsanleitung

Cisco

Cisco ASR 5000 Series Bedienungsanleitung

Cisco

Cisco Comcast Xfinity DPC3939 Bedienungsanleitung

Cisco

Cisco IG21-VZ-K9 Bedienungsanleitung

Cisco

Cisco Firepower 2100 Bedienungsanleitung

Cisco

Cisco Expressway CE1200 Bedienungsanleitung

Cisco

Cisco Linksys WAG310G Bedienungsanleitung

Cisco

Cisco Meraki Go Betriebsanleitung

Cisco

Cisco 2650XM Montage- und Bedienungsanleitung

Cisco

Cisco ASR 5000 Series Bedienungsanleitung

Cisco

Cisco Linksys WAG310G Bedienungsanleitung

Cisco

Cisco DPC2425 Bedienungsanleitung

Cisco

Cisco SIEMENS HICOM 330E Montage- und Bedienungsanleitung

Cisco

Cisco ASR 5000 Series Bedienungsanleitung

Cisco

Cisco DDR2201 Series Betriebsanleitung

Cisco

Cisco 2621XM Bedienungsanleitung

Cisco

Cisco AS5400XM Bedienungsanleitung

Cisco

Cisco Meraki Z3C Bedienungsanleitung

Cisco

Cisco AS5400 Series Bedienungsanleitung

Cisco

Cisco ASR 9000 Series Bedienungsanleitung

Cisco

Cisco AS5400XM Bedienungsanleitung

Cisco

Cisco Catalyst 8200 Series Bedienungsanleitung

Cisco

Cisco ASR 5000 Bedienungsanleitung

Cisco

Cisco TES301 Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung