Cisco 7925G-EX Bedienungsanleitung
Wavelink Avalanche Server
•Wavelink Avalanche Server Overview, page 1
•Before You Begin, page 1
•Best Practices, page 2
•Wavelink Server IP Address Setup, page 2
•Set Up and Use CU, page 3
•Install CU File, page 5
•Update Configuration Files, page 5
•Update Phone, page 12
Wavelink Avalanche Server Overview
This chapter describes the Wavelink Avalanche Management Console and how to use it to configure the Cisco
Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G. The Configuration Utility (CU) for Wavelink
Avalanche can be installed on the Wavelink Avalanche Management Console and used to configure a single
phone or multiple phones with common settings.
Not all features can be configured using Wavelink. Some features can only be configured from Cisco
Unified Communications Manager Administration.
Note
Before You Begin
Before you can use the Wavelink Avalanche Management Console to configure phones, ensure that you have
the necessary components and follow the best practices during your setup.
The following components are required for configuring the phone using the Wavelink Avalanche server:
•Wavelink Avalanche software:
◦Avalanche Manager Agent
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Administration Guide
1
◦Avalanche Management Console
•Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Firmware Release 1.3(1) or later
•Configuration Utility (CU) for Wavelink Avalanche
•DHCP server
•Cisco Unified Communications Manager
Best Practices
This section describes the best practices recommended for setting up and using the CU on the Wavelink
Avalanche server.
•Ensure that the phone is registered to Cisco Unified Communications Manager.
•Try out this process with one or two phones before deploying to many phones.
•Set up a VLAN that has access only to the Wavelink server.
•Configure DHCP Option 149 with the Wavelink server IP address. If you do not configure this option,
see Set Up Wavelink Server Address from Phone, on page 2.
•Configure a Cisco Access Point to use a default SSID of “cisco”with open authentication and no
encryption.
Wavelink Server IP Address Setup
If you did not configure DHCP Option 149 with the Wavelink server IP address, you must manually assign
it.
Do not perform this task if you previously configured the Wavelink server address using DHCP Option
149.
Note
The following sections describe the methods to assign the Wavelink server on the phone.
Set Up Wavelink Server Address from Phone
To assign the Wavelink server from the phone, follow these steps.
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Administration Guide
2
Wavelink Avalanche Server
Best Practices
Procedure
Step 1 Turn on the phone.
Step 2 Verify that the phone is installed with the required firmware version and is registered to Cisco Unified
Communications Manager.
Step 3 Choose SETTINGS >System Configuration >Wavelink.
Step 4 To unlock the phone, press **#.
Step 5 In the Alternate Wavelink Server option, choose Yes.
Step 6 Enter the IP address of the Wavelink server, and press Save.
Set Up Wavelink Server Address from Phone Web Page
To assign the Wavelink server using the phone web page, follow these steps.
Procedure
Step 1 From the phone web page, choose Wavelink Settings from the left pane.
Under Wavelink Settings, make sure that the server is enabled.
Step 2 Click Use the following Server and enter the IP address of the server.
Step 3 Click Save.
Set Up and Use CU
This section describes the tasks for configuring and using the CU from the Wavelink Management Console.
The CU is labeled as 7921G but the CU works for all 792X phones.Note
To set up and use the CU from the Wavelink Management Console, perform the following tasks.
Procedure
Step 1 Assign attributes for the phone. For more information, see Phone Attributes Setup, on page 4.
Step 2 Install the CU on Wavelink. For more information, see Install CU File, on page 5.
Step 3 Update the configuration files. For more information, see Update Configuration Files, on page 5.
Step 4 Update the phones. For more information, see Phone Attributes Setup, on page 4.
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Administration Guide
3
Wavelink Avalanche Server
Set Up Wavelink Server Address from Phone Web Page
Phone Attributes Setup
You can assign attributes on the Cisco Unified Wireless IP Phone that can be used to distinguish it from other
mobile devices connected to the Wavelink server. These attributes can be used as search criteria for locating
phones on the Wavelink server. For example, the predefined ModelName field of CP7925G is used to identify
a device as the Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G.
To assign attributes, use the Wavelink Management Console, the phone UI, or the phone web page:
•If you use the Wavelink Management Console, choose the Add Properties option from the Client Settings
option (for a single phone) or the Edit Device Properties option (for a mobile device group). For more
information, see the Wavelink Avalanche server documentation.
•If you assign attributes from the phone or phone web page, use the following sections to define values
for the CustomName and CustomValue fields.
Define CustomName and CustomValue on Phone
To define the CustomName and CustomValue fields from the phone, follow these steps:
Procedure
Step 1 On the main phone screen, choose SETTINGS >System Configuration >Wavelink.
Step 2 Unlock the phone by pressing **#.
Step 3 Scroll to a CustomName, enter an attribute name (for example, “User”), and click Save.
Only alphanumeric characters are allowed in the CustomName
field.
Note
Step 4 Scroll to CustomValue and enter a value for the corresponding CustomName (for example, “Admin”), and
click Save.
You can define up to four pairs of custom parameters.
Define Custom Parameters from Phone Web Page
To define customer parameters from the phone web page, follow these steps:
Procedure
Step 1 From the phone web page, choose Wavelink Settings.
Step 2 In the Wavelink Custom Parameters section, enter values in the Name and Value fields. You can define up
to four pairs of custom parameters.
Do not use spaces in the Name
field.
Note
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Administration Guide
4
Wavelink Avalanche Server
Phone Attributes Setup
Install CU File
The CU file is provided by Cisco in the .ava file format.
Install the CU on the Wavelink Avalanche Management Console.Note
For more information, see the Wavelink Avalanche Management Console documentation.
To install the phone CU, follow these steps.
Procedure
Step 1 Launch the Wavelink Avalanche Management Console and connect to the agent.
Step 2 Choose Software Management >Install Software Package.
Step 3 Browse to the location of the .ava file containing the CU and select it.
Step 4 Click New and enter the software collection name under which the phone configuration files will be added.
Step 5 Follow the instructions on the wizard to complete the installation.
Step 6 When the installation completes, expand the software collection name on the left pane. The phone CU file
name 7925CU appears with a red “x”(disabled) next to it.
Step 7 Right-click 7925CU and choose Enable Package.
The installation is complete. The following additional steps are optional. They configure the selection
criteria so you can easily apply changes to a device group.
Note
Step 8 Right-click the software collection (containing the phone CU) and choose Settings.
Step 9 Click the button at right of the Selection Criteria box to launch the Selection Criteria wizard.
Step 10 Select an item from the Source Properties list on the left, and enter a value in the Selection Expression text
box.
Step 11 Repeat the previous step for each property and value you wish to include. When finished, click Compile, and
then click Test Expression.
Step 12 Review the list displayed under Matching Clients to ensure the selection criteria have been met.
Step 13 Click Apply, then click OK.
Update Configuration Files
You can update a phone configuration file using the CU installed on a Wavelink Avalanche Management
Console.
The following table lists the configuration file settings.
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Administration Guide
5
Wavelink Avalanche Server
Install CU File
Table 1: Configuration File Settings
For more information, see...Setting
Profile Settings Fields, on page 6Profile Settings
WLAN Settings
Network Settings
USB Settings Field, on page 11USB Settings
Trace Settings Fields, on page 11Trace Settings
Wavelink Settings Fields, on page 12Wavelink Settings
To update settings in the phone configuration file, follow these steps:
Procedure
Step 1 Right click 7925CU (in a folder under Software Collections) to launch the CU.
Step 2 From the left pane, choose the settings you wish to configure:
•Profile Settings
•USB Settings
•Trace Settings
•Wavelink Settings
Step 3 From the settings page, select or enter information for those settings.
Step 4 Click Apply.
Profile Settings Fields
The following table lists the fields in the Profile Settings screen.
Table 2: Profile Settings
For more information, see …
DescriptionItem
Provides a name for the profile to make it easy to
identify; up to 63 alphanumeric characters.
Profile Name
Choose Yes or No.Profile Enabled
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Administration Guide
6
Wavelink Avalanche Server
Profile Settings Fields
For more information, see …
DescriptionItem
WLAN Settings
Assigns the Service Set Identifier (SSID) to this
profile. You must assign the same SSID to the
phone that is also assigned to access points in the
wireless network.
SSID
802.11 Standards for WLAN
Communications
Determines the signal mode or priority for
selecting signal modes available in the WLAN.
Options are:
•802.11 b/g: Use only 2.4 GHz band
•802.11a: Use only 5 GHz band
•Auto, 802.11b/g preferred over 802.11a
(dual-band)
•Auto, 802.11a preferred over 802.11b/g
(dual-band)
The preferred band, if available, is used
at power-on, but the phone may switch
to the less-preferred 2.4 GHz band, if
available, and the preferred band is lost.
After the phone has connected to the
less-preferred band, it does not scan for
the preferred band if the current band is
acceptable, and will remain connected
to the less-preferred band.
Note
•Auto, signal strength (RSSI): Use strongest
signal in dual-band environment
WLAN Mode
802.11 Standards for WLAN
Communications
Set for the type of power saving mode used in the
WLAN. Options are:
•U-APSD/PS-Poll
•None
Call Power Save
Mode
WLAN Security
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Administration Guide
7
Wavelink Avalanche Server
Profile Settings Fields
For more information, see …
DescriptionItem
Sets the authentication and encryption methods
for this profile:
Open
Open access to APs
Open+WEP
Open access with WEP encryption
(requires an encryption key)
Shared+WEP
Shared key authentication with WEP
(requires an encryption key)
LEAP
Cisco proprietary authentication and
encryption using a RADIUS server
(requires a username and password)
EAP-FAST
Authentication and encryption using TLS
and RADIUS server (requires a username
and password)
Auto (AKM)
Automatic authenticated key management
using:
•WPA, WPA2 (requires a username
and password)
•WPA-Pre-shared key,
WPA2-Pre-shared key (requires a
passphrase/pre-shared key)
•CCKM (requires a username and
password)
Authentication
Mode
Required for LEAP, EAP-FAST, and Auto (AKM) authentication methodsWireless Security
Credentials
Assigns the network authentication username for
this profile
Username
Assigns the network authentication password for
this profile
Password
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Administration Guide
8
Wavelink Avalanche Server
Profile Settings Fields
For more information, see …
DescriptionItem
Sets the pre-shared key for this profileWPA Pre-shared
Key Credentials
Determines the key type: Hex or ASCIIPre-shared Key
Type
Identifies the keyPre-shared Key
Required for Open+WEP and Shared+WEP authentication methodsWireless
Encryption
Determines the encryption key type: Hex or
ASCII
WEP Keys Type
Identifies the Transmit Key.WEP Keys TxKey
Determines the WEP key length with key size of
40 or 128 bits.
WEP Key Length
1-4
Defines the WEP key value:
40 bits
5 ASCII or 10 hexadecimal characters
128 bits
13 ASCII or 26 hexadecimal characters
WEP Key Value
1-4
Network Settings
Yes
Enables DHCP to obtain IP address and
DNS servers automatically.
No
DHCP is disabled and you will need to
enter the following fields:
•IP Address
•Subnet Mask
•Default Router
•Primary DNS
•Secondary DNS
•Domain Name
DHCP Enabled
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Administration Guide
9
Wavelink Avalanche Server
Profile Settings Fields
For more information, see …
DescriptionItem
TFTP
Determines whether DHCP assigns the TFTP
server.
If yes, enter static IP addresses for:
•TFTP Server 1
•TFTP Server 2
Alternate TFTP
Advanced WLAN Settings
TSPEC Settings
Minimum data rate that outbound traffic usesMinimum PHY
Rate
Excess bandwidth beyond application
requirements
Surplus Bandwidth
Antenna Settings
•Vertical
•Horizontal
•Diversity
Antenna Selection
for 802.11A
•Vertical
•Horizontal
•Diversity
Antenna Selection
for 802.11B
Enabled: Identifies enabled channels in WLAN
to improve scanning for the phone.
Max Tx Power: Sets the maximum transmit power
for the phone.
802.11G Power
Settings
Enabled: Identifies enabled channels in WLAN
to improve scanning for the phone
Max Tx Power: Sets the maximum transmit power
for the phone
802.11A Power
Settings
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Administration Guide
10
Wavelink Avalanche Server
Profile Settings Fields
Andere Handbücher für 7925G-EX
2
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Cisco IP-Telefon Handbücher
Cisco
Cisco SPA525G - Small Business Pro IP Phone VoIP Bedienungsanleitung
Cisco
Cisco Cisco 7960 Service-Handbuch
Cisco
Cisco Unified 6921 Bedienungsanleitung
Cisco
Cisco Cisco 7940 Bedienungsanleitung
Cisco
Cisco Small Business Pro SPA 509G Bedienungsanleitung
Cisco
Cisco 7975G - Unified IP Phone VoIP Handbuch
Cisco
Cisco 8800 Series Bedienungsanleitung
Cisco
Cisco 7942G - Unified IP Phone VoIP Bedienungsanleitung
Cisco
Cisco WIP310 - iPhone Wireless VoIP Phone Bedienungsanleitung
Cisco
Cisco MCS 7800 Series Bedienungsanleitung
Cisco
Cisco 7925G - Unified Wireless IP Phone VoIP Bedienungsanleitung
Cisco
Cisco 7941G - Unified IP Phone VoIP Bedienungsanleitung
Cisco
Cisco 794X Bedienungsanleitung
Cisco
Cisco 7921G - Unified Wireless IP Phone VoIP Bedienungsanleitung
Cisco
Cisco DATAVOX 7941 Bedienungsanleitung
Cisco
Cisco Unified 6921 Bedienungsanleitung
Cisco
Cisco 7902G - Unified IP Phone VoIP Bedienungsanleitung
Cisco
Cisco i2002 Bedienungsanleitung
Cisco
Cisco Unified 7912G Bedienungsanleitung
Cisco
Cisco 7941G - Unified IP Phone VoIP Bedienungsanleitung
