Cisco AIR-MP20B Bedienungsanleitung

Preface

This guide is designed to help you install an IEEE 802.11g-compliant radio

in a Cisco Aironet 1100 or 1200 Series Access Point. Detailed installation

and configuration information can be found in the following documents:

•Cisco Aironet 1100 Series Access Point Hardware Installation Guide

•Cisco Aironet 1200 Series Access Point Hardware Installation Guide

•Cisco IOS Software Configuration Guide for Cisco Aironet Access

Points

Note Before installing your 802.11g radio, make sure that you upgrade to

Cisco IOS Release 12.2(13)JA or later. If you do not upgrade, the

access point will continually reboot.

Documentation for the 1100 and 1200 series access points is available at

Cisco.com. Follow these links to access them:

http://cisco.com/en/US/products/hw/wireless/ps4570/tsd_products_support_

series_home.html

http://cisco.com/en/US/products/hw/wireless/ps430/tsd_products_support_s

eries_home.html

Introduction

The Cisco Aironet IEEE 802.11g-compliant radio (hereafter called the

802.11g radio) is designed to upgrade 1100 and 1200 series access points to

IEEE 802.11g standards. The radio delivers 100 milliwatts (mW) maximum

transmit power at 1, 2, 5.5, and 11 megabits per second (Mbps) data rates and

30 mW maximum at all other data rates. The radio supports data rates of up

to 54 Mbps.

This guide provides instructions for installing or replacing an 802.11g radio

in an 1100 or 1200 series access point. The following operations summarize

the upgrade procedure:

1. Remove all cables and power connections from the access point.

2. Follow standard electrostatic discharge (ESD) procedures.

3. Place the access point on an ESD-protected work surface.

4. Open the access point’s radio access cover.

5. Install the new 802.11g radio card.

6. Close the access point’s radio access cover.

Caution ESD can damage the Cisco Aironet client radio and the internal

components of the access point. It is recommended that the

802.11g radio upgrade procedures be performed by an

ESD-trained service technician at an ESD-protected

workstation.

Unpacking the Radio

Each 802.11g radio is shipped with the following items:

•This radio upgrade guide

•A product registration card

•A T-10 tamper-resistant Torx L-wrench (for 1200 series access points

only)

•Access point compliance labels (one for the 1100 and two for the 1200

series access points)

If anything is missing or damaged, contact your Cisco representative for

support.

1100 Series Installation Instructions

Note Before installing your 802.11g radio, make sure that you upgrade to

Cisco IOS Release 12.2(13)JA or later. If you do not upgrade, the

access point will continually reboot.

Preparing the Access Point and Work Area

Follow these steps to prepare your access point and work area before

installing the 802.11g radio:

1. Remove all cables and power connections from the access point.

2. Place the access point on an ESD-protected work surface.

3. Remove all static-generating items from the work area, such as plastic

material, styrofoam cups, and other similar items.

4. Place the access point and the new 802.11g radio (in its antistatic bag)

on an antistatic work surface.

5. Discharge any static buildup on your body by touching a grounded

surface (antistatic work surface) before proceeding.

6. Follow standard ESD procedures during all phases of the process.

Removing the Back Cover

Follow these steps to remove the access point’s back cover:

1. Position the access point so that its back cover is facing up.

Caution ESD can damage the internal access point components and the

802.11g radio if they are not handled properly.

2. Remove the back-cover retaining screw using a Philips screwdriver as

shown in the following illustration.

1Back cover screw 2Back cover

95757

3. Hold the front cover with one hand, and with the other hand gently slide

the back cover towards the connector end of the unit.

4. Gently lift the connector end of the back cover and remove the cover.

Removing the 2.4-GHz Radio

Follow these steps to remove the 2.4-GHz radio card from your access point:

1. Gently lift the top of the antenna card until it clears the plus-shaped (+)

support post as shown in the following illustration.

2. Gently pull the antenna card to remove it from the notch in the support

bracket. Do not disconnect the antenna wire connectors.

3. Push the card-retaining clips (on each side of card) away from the radio

card (see the previous illustration). When released, the radio card springs

up. Do not disconnect the antenna wires.

1Plus-shaped (+) support post 42.4-Ghz radio card

2Antenna card 5Card retaining clips

3Support bracket 6Mini-PCI connector

95755

Note If the radio card does not spring up, slightly loosen the support

bracket screws.

4. Remove the 2.4-GHz radio card from the mini-PCI connector by

performing the following operations:

a. Grasp the radio card only on the edges, being careful not to touch

components on the board or the gold connector pins.

b. Remove the 2.4-GHz card from the mini-PCI connector.

5. Place the radio card and antenna card on the ESD-protected work

surface.

Caution You can damage the connectors if you use long-nose pliers or

similar tools during the removal process. To avoid damaging the

antenna wire assemblies, remove them by hand.

6. Use your fingers to carefully remove the antenna wire connectors from

the 2.4-GHz radio card. Do not remove the antenna wire connectors from

the antenna board.

Caution Do not pull the antenna wire to remove the connector from the

radio card. Damage to the wire and connector will result.

7. Place the 2.4-GHz radio card into an anti-static bag.

Note Do not put the antenna card in the anti-static bag. You will

connect it to the 802.11g radio card.

1Antenna card 22.4-GHz radio card

95751

Installing the 802.11g Radio

Follow these steps to install the 802.11g radio:

Caution ESD can damage the internal access point components and the

802.11g radio if they are not handled properly.

1. Carefully remove the 802.11g radio from its anti-static bag.

2. Grasp the card only on the edges, being careful not to touch components

on the board or the gold connector pins.

3. Place the radio on the anti-static work surface next to the antenna card.

Caution Do not use long-nose pliers or similar tools. To avoid damaging

the antenna wire assemblies, handle them by their connectors.

4. Use your fingers to carefully connect the antenna wire connectors to the

mating connectors on the 2.4-GHz radio card as shown in the illustration

on the following page.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Drahtloser Zugangspunkt Handbücher

Cisco

Cisco Aironet 1520 Series Bedienungsanleitung

Cisco

Cisco 1242AG - Aironet - Wireless Access Point Handbuch

Cisco

Cisco Aironet 600 Series Bedienungsanleitung

Cisco

Cisco Linksys WAP55AG Bedienungsanleitung

Cisco

Cisco Meraki MR55 Bedienungsanleitung

Cisco

Cisco Aironet 1530 Bedienungsanleitung

Cisco

Cisco 1130AG - Aironet - Wireless Access Point Bedienungsanleitung

Cisco

Cisco aironet 2800 series Kurzanleitung

Cisco

Cisco Aironet 1140 Series Bedienungsanleitung

Cisco

Cisco Aironet 3500 Series Bedienungsanleitung

Cisco

Cisco ASA 5506W-X Bedienungsanleitung

Cisco

Cisco Catalyst Wireless 9163E Bedienungsanleitung

Cisco

Cisco MERAKI MR44 Bedienungsanleitung

Cisco

Cisco Catalyst 9130AX Series Bedienungsanleitung

Cisco

Cisco Cisco Aironet Wireless LAN Client Bedienungsanleitung

Cisco

Cisco Aironet 1830 Series Bedienungsanleitung

Cisco

Cisco WAP125 Bedienungsanleitung

Cisco

Cisco WET200 Wireless-G Business Ethernet Bridge Bedienungsanleitung

Cisco

Cisco Meraki MR20-HW Bedienungsanleitung

Cisco

Cisco Aironet 340 Series Handbuch

Cisco

Cisco Linksys WAP54G LA Bedienungsanleitung

Cisco

Cisco Small Business WAP551 Bedienungsanleitung

Cisco

Cisco WAP121 Bedienungsanleitung

Cisco

Cisco MERAKI MR72 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung