Clarion UNGO MS2106 Bedienungsanleitung

MS2106

MS2106 owner 7-14.qxd 7/14/2003 1:42 PM Page 1

CONTENTS

1. Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2. Ungo-Net Interface Introduction . . . . . . . . . . . . . . . . . . . . . . . 2

3. Remote Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

3.1 Remote Transmitter Layout . . . . . . . . . . . . . . . . . . . . . . 3

3.2 Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

4. System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3.1 Arming Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3.2 Passive Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3.3 Disarming Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3.4 Driver’s Door Priority Unlock . . . . . . . . . . . . . . . . . . . . . 4

3.5 Auto Rearm Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3.6 Chirp Delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3.7 Ignition Controlled Door Locks . . . . . . . . . . . . . . . . . . . 4

3.8 Remote Panic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3.9 Emergency Override . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3.10 Valet Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3.11 Optional Trunk Release . . . . . . . . . . . . . . . . . . . . . . . . 6

3.12 Optional Trunk Disarm Feature . . . . . . . . . . . . . . . . . . . 6

3.13 Remote Sensor Bypass . . . . . . . . . . . . . . . . . . . . . . . . 6

3.14 Programming Remote Transmitters . . . . . . . . . . . . . . . . 6

3.16 Transmitter Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.17 Status Indicator (LED) Functions . . . . . . . . . . . . . . . . . . 7

3.18 Siren Chirp Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

5. User Selectable Programming Options . . . . . . . . . . . . . . . . . . 8

5. Reference Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

6. Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

7. Installation Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

MS2106 owner 7-14.qxd 7/14/2003 1:42 PM Page 2

1. FEATURES

Ungo Security Systems are state-of-the-art vehicle protection systems equipped with

features designed to:

Deter potential intrusions to the vehicle by continually flashing the system LED status

indicator while the system is Armed, giving a visual indication to any passer-by that the

vehicle is equipped with a security system.

Detect intrusions to the vehicle, including impacts to the vehicle’s body, and opening of

the doors, trunk and hood*.

Alert those in the vicinity of the vehicle by sounding the system’s siren and flashing the

parking lights, and honking the horn*.

Inform the owner when the system has been triggered and specifically which zone was

violated. The system will also inform the user of any defective zones or sensors that

may be causing the system to function improperly.

Protect both you and the contents of your vehicle with features such as panic mode,

dome light illumination*, and ignition controlled door locking*.

* Optional Features

Note:

Some features may require additional parts and labor, and may not be appropriate for

certain vehicles. Consult your authorized Ungo dealer for assistance.

Standard Features

•Two 5-Button VariCode

Remote

Transmitters

•Status Indicator (LED)

•Multi-Tone 120dB Siren

•Dual Stage Shock Sensor

•Built-in Starter Disable

•Coded Emergency Override

•Ungo-Net Interface

•Flashing Parking Lights

Optional Features

•Keyless Entry

•Remote Trunk/Hatch Release

•Dome Light Supervision

•Hood and Trunk Protection

•Remote Auto Start

•Power Window Roll Up

•Driver's Door Priority Locks

•Radar Sensor

•Remote Head

Light Control

MS2106 owner 7-14.qxd 7/14/2003 1:42 PM Page 3

1. Ungo-Net Interface Introduction

This product is equipped with Ungo’s newest and most revolutionary technology

to date, the Ungo-Net bus system. Ungo-Net is a network system that allows

expansion, flexibility, and superior vehicle security through digital

communication. This is established through a PC link through either a computer

or PDA, similar to a USB port on a PC. Utilizing this interface, the alarm system

and remote transmitters can be configured to best suit the needs of the

operator. This includes arming mode selections, auxiliary functions, multiple

vehicle operation, transmitter configuration, and interface modules.

For additional convenience and operation, households with multiple vehicles

can utilize a single remote transmitter to operate 2 vehicles. Eliminating the

cumbersome cluster of multiple remote transmitters. Also, the remote

transmitters can be customized to better suit the needs of the operator. The

Arm and Disarm buttons can be consolidated into the one button with the

remaining buttons controlling assignable features.

Capitalizing on Ungo-Net, an optional LCD FM transmitter kit can be added to

the security system (part #. FMKIT). This transmitter features 2-way

communication via FM frequency for increased transmitting range and

operation. With audible and visual confirmations, the operator can be aware of

the vehicles status and notified about violation attempts.

In addition, system configuration, software upgrades, and diagnostics can be

performed through the Ungo-Net port. Thus allowing the Ungo dealer to

maintain the utmost protection and serviceability of the security system. Ungo-

Net also allows the dealer to trouble shoot false triggers and set sensor

calibration eliminating countless hours of guesswork.

Ungo-Net Accessories

PCLINK: Includes Ungo-Net software, serial cable, instructions, and power

supply.

FMKIT: Includes SAA217T (FM transmitter), extended range antenna,

instructions, and FM receiver module.

AUX BOX: I

ncludes receiver module, wiring harness, and instructions.

MS2106 owner 7-14.qxd 7/14/2003 1:42 PM Page 4

3. REMOTE TRANSMITTER

3.1 Remote Transmitter Layout

The Ungo MS2106 comes with 2 Random Code Remote Transmitters used to

control the system’s features. Each time a transmitter button is pressed, the LED

will flash to indicate that a transmission is taking place.

Button 1 Arms the system and locks the doors.*

Button 2 Disarms the system and unlocks the doors.* If the optional Driver’s Door

Priority Unlocking feature is installed, pressing Button 2 Disarms the system and

unlocks only the driver’s door. Pressing Button 2 again unlocks all doors.

Button 3 Activates the system’s auxiliary 1 output (usually used for trunk release).*

Button 4 Activates the system’s auxiliary 2 output.*

The Level Shift Button temporarily changes the function of buttons 1-4 allowing

expanded operation and multi-car compatibility. Each time the Level Shift button is

pressed, a new level of commands are accessed up to a maximum of four levels

(Level Shift three times). Note: pages 3 and 4 are reserved for channel expansion

modules or multi-car operation. See your Authorized Ungo Dealer for details.

*Optional feature

3.2 Battery Replacement

Your Ungo Remote Transmitter uses a 12 volt alkaline battery (type 23A), which will

need to be replaced from time to time. Under normal conditions, the battery may

last more than 6 months before it needs replacement. When your Remote

Transmitter’s battery needs replacement, you will notice a decrease in operating

range or a decrease in the brightness of the Transmitter’s LED indicator.

To change the battery, remove the 2 screws at the back of the Transmitter and

carefully separate the top and bottom halves of the Transmitter case. Insert the

new battery, carefully observing proper polarity, then replace the cover.

Auxiliary 1

Auxiliary 3

w/ Shift

Arm/Lock

Silent Arm

w/ Shift

Disarm/Unlock

Silent Disarm

w/ Shift

Level Shift

Auxiliary 2

MS2106 owner 7-14.qxd 7/14/2003 1:42 PM Page 5

3. SYSTEM OPERATION

3.1 Arming Operation

To arm the alarm system, press Lock button on the transmitter:

•The siren will chirp once.

•The parking lights will flash once.*

•The doors will lock.*

•The LED will come on solid for 5 seconds, and then begin to flash. After 10

seconds the alarm system is armed.

*Optional feature

3.2 Remote Sensor Bypass

To arm the system and bypass the shock sensor, hood/trunk inputs, press the Lock

button to Arm, then within 2 seconds press the Lock button again. The siren will

chirp 5 times to indicate Sensor Bypass mode. The doors will still be monitored.

3.3 Passive Arming (Programmable feature)

The passive arming feature allows the system to arm automatically. The remote

transmitter still can be used to arm the system at any time. This option is user

programmable (see User Accessible Programming Options).

To arm the alarm system passively:

1. Turn the ignition Off.

2. Exit the vehicle and close all the doors.

•The LED will begin flashing rapidly to indicate the system is preparing to arm.

•The siren will chirp 30 seconds after the last door is closed to indicate the

system is armed.

•The doors will lock.*

*Optional feature

3.4 Disarming Operation

To disarm the system press the Unlock button on the transmitter:

•The siren will chirp twice.**

•The parking lights will flash twice.*

•The doors will unlock.*

•The dome light will turn on for 30 seconds.*

*Optional feature

f the alarm was triggered while away, the system will respond with 3 chirps

and 3 parking light flashes, see Tamper Alert.

MS2106 owner 7-14.qxd 7/14/2003 1:42 PM Page 6

3.5 Tamper Alert

On Disarming, if the system responds with three chirps, indicating the system was

triggered, turn on the ignition and the LED will flash the triggered zone 5 cycles.

LED Flashes (60 seconds):

1 flash = optional sensor

2 flashes = shock sensor

4 flashes = door

5 flashes = trunk

example: flash-flash-pause-flash-flash-pause = shock sensor

3.6 Silent Arming / Disarming (Programmable feature)

As an option, the system can be programmed to always Arm and Disarm the with

or without chirp confirmation (see User Accessible Programming Options).

To temporarily cancel the Arming and Disarming confirmation chirps, press the

Level Shift Button followed by the Arm or Disarm Button.

Note: The confirmation chirps will only be cancelled if the system status is normal.

The chirp indications for Tamper Alert and the open zone warning will not be

cancelled when the system is Armed or Disarmed silently.

3.7 Optional Driver's Door Priority Unlock

The optional Driver’s Door Priority Unlock feature provides a higher level of

personal safety by unlocking only the driver’s door upon disarming. Once

disarmed, pressing the disarm button again will unlock all doors. This optional

feature may require addtional parts and labor, consult your Authorized Ungo dealer

for more information.

3.8 Auto Rearm Feature (Programmable feature)

The Auto Rearm feature allows the system to automatically rearm itself in the event

the system becomes disarmed and a door is not opened within 30 seconds. This

option is user programmable (see User Selectable Programming Options).

3.9 Ignition Controlled Door Locks (Programmable feature)

The ignition door-locking feature allows the doors to automatically lock when the

ignition is turned On, and automatically Unlock when the ignition is turned Off.This

option is user programmable (see User Selectable Programming Options).

MS2106 owner 7-14.qxd 7/14/2003 1:42 PM Page 7

3.10 Remote Panic Feature

In the event of an emergency (PANIC) situation, the system's siren can be triggered

for 45 seconds to attract attention. To activate the Panic feature, press and hold

the Lock button for 3 seconds.

•The siren will sound.

•The parking lights will flash.*

•The doors will unlock.*

•The starter disable will turn Off.*

*Optional feature

3.11 Coded Emergency Override (Programmable feature)

If the remote transmitter becomes lost or fails to operate, use the emergency

override feature to disarm the alarm system. Be sure that you have your ignition

keys ready and that you know the location of the Override switch before you

perform this procedure.

To override the system:

1. Enter the vehicle.

•Because the alarm system is armed, the siren will sound.

2. Turn the ignition On.

3. Press the Override switch a number of times equal to the disarm code and

continue holding for 10 seconds on the last press. (If the default code setting

has not been changed, press and hold the override switch for 10 seconds to

disarm to system.)

•The system will disarm.

•The siren will stop sounding.

•Starter disable will turn Off.

4. You can now start and drive the car.

5. If the disarm code is not entered correctly, turn off the ignition and begin again

at step 2.

6. Consult your authorized Ungo dealer to check the alarm system.

The default setting for the Emergency Override Disarm Code is 1. To change the

Emergency Override Code see User Selectable Programming Options, step 6.

Note: During installation, your installer can program the system to give a 15 second

entry delay when the system Arms passively. When the door is opened after the

system is Armed, the siren will give a series warning of chirps before sounding,

giving you time to perform the emergency override procedure.

MS2106 owner 7-14.qxd 7/14/2003 1:42 PM Page 8

3.12 Valet Mode

When placed into Valet Mode the security system will be disabled. However, the

optional keyless entry and auxiliary outputs will still function if installed.

To enter the Valet Mode:

1. Be sure the alarm system is disarmed.

2. Press and hold the Valet/Override button.

3. Turn the ignition On.

4. Continue holding the Valet/Override button for 3 seconds.

5. Turn the ignition Off.

•The siren will chirp once.

•The LED will turn On solid indicating the system is in Valet mode.

To exit Valet Mode:

1. Press and hold the Valet/Override button down.

2. Turn the ignition On.

3. Hold the Valet/Override button for 3 seconds.

4. Turn the ignition Off.

•The siren will chirp twice.

•The LED will turn off indicating the system is out of Valet mode.

3.13 Optional Trunk Release

Press the Trunk button for approximately 3 seconds to open the trunk. This

optional feature may require addtional parts and labor, consult your Authorized

Ungo dealer for more information.

3.14 Optional Trunk Disarm Feature

The trunk disarm feature allows the alarm to disarm automatically when the Trunk

button is used to activate the optional trunk release. This eliminates having to

disarm the alarm system prior to activating the trunk release. This optional feature

may require addtional parts and labor, consult your Authorized Ungo dealer for

more information.

3.15 Programming Remote Transmitters

Make sure to have the desired transmitters ready and follow the steps below.

To program transmitters:

1. Turn the ignition ON, OFF, ON, OFF, and leave ON.

2. Press and hold the Valet/Override switch for 5 seconds.

•The siren will chirp once.

MS2106 owner 7-14.qxd 7/14/2003 1:42 PM Page 9

3. Press the Lock button on the transmitter.

•The siren will chirp once.

4. Press the Lock button on the transmitter again.

•The siren will chirp twice.

5. Repeat steps 3 and 4 for each additional transmitter.

6. Turn OFF the ignition when transmitter programming is complete.

•The siren will chirp 3 times.

MS2106 owner 7-14.qxd 7/14/2003 1:42 PM Page 10

Inhaltsverzeichnis

Andere Clarion Autoalarmanlage Handbücher

Clarion

Clarion Ungo MS2000 Bedienungsanleitung

Clarion

Clarion Ungo MS850 Bedienungsanleitung

Clarion

Clarion UNGO MS8200 Bedienungsanleitung

Clarion

Clarion UNGO MS3200 Bedienungsanleitung

Clarion

Clarion UNGO MS5500 Bedienungsanleitung

Clarion

Clarion Ungo MS2004 Bedienungsanleitung

Clarion

Clarion Ungo Pro Security SR1000 Bedienungsanleitung

Clarion

Clarion UNGO CS105 Bedienungsanleitung

Clarion

Clarion UNGO ProSecurity S100 Bedienungsanleitung

Clarion

Clarion UNGO ProSecurity S100 Bedienungsanleitung

Clarion

Clarion UNGO MS2007 Bedienungsanleitung

Clarion

Clarion UNGO MS2005 Bedienungsanleitung

Clarion

Clarion UNGO PRO SECURITY K20 Bedienungsanleitung

Clarion

Clarion UNGO ProSecurity SR6000 Bedienungsanleitung

Clarion

Clarion UNGO MS3001 Bedienungsanleitung

Clarion

Clarion UNGO Pro Security S670 Bedienungsanleitung

Clarion

Clarion G1100 Bedienungsanleitung

Clarion

Clarion Ungo MS2004 Bedienungsanleitung

Clarion

Clarion Ungo MS850 Bedienungsanleitung

Clarion

Clarion UNGO MS2105 Bedienungsanleitung

Clarion

Clarion UNGO MS2100 Bedienungsanleitung

Clarion

Clarion Ungo MS1001 Bedienungsanleitung

Clarion

Clarion UNGO MS5500 Handbuch

Clarion

Clarion UNGO ProSecurity S660 Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung