Clarke DEVIL 370SPC Installations- und Betriebshandbuch

OPERATING & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC1119 ISS3

DEVIL QUARTZ HALOGEN HEATER

MODEL NO: DEVIL 370SPC

PART NO: 6926013

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Quartz Halogen Heater.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

SPECIFICATIONS

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

Model Number Devil 370SPC

Part Number 6926013

Weight 14 kg

Dimensions (LxWxH) 610 x 620 x 790 mm

Wattage 2.8 kW

Amperage 12.17 A

Supply Voltage 230 V/50 Hz

Fuse Rating 13 A

Insulation Class IP20

Max Heat Output 2.8 kW

Duty cycle Continuous

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

THE FOLLOWING TABLE ADDRESSES THE INFORMATION

REQUIREMENTS OF REG.2015/1188

Item Symbol Value Unit

Heat output

Measured seasonal space heating energy efficiency 36%

Nominal heat output Pnom 3.0 kW

Minimum heat output (indicative) P min 1.5 kW

Maximum continuous heat output P max 3.0 kW

Auxiliary electricity consumption

At nominal heat output elmax n/a kW

At minimum heat output el min n/a kW

In standby mode elSB 0kW

Type of heat input for electric storage local heaters only

Manual heat charge control with integrated thermostat No

Manual heat charge control with room and/or outdoor temperature

feedback

Electronic heat charge control with room and/or outdoor temperature

feedback

Fan assisted output No

Type of heat output/room temperature control (select one)

Single stage heat output, no temperature control No

Two or more manual stages, no temperature control Yes

With mechanical thermostat temp control No

With electronic temperature control No

Electronic temperature control with day timer No

Electronic temperature control with week timer No

Other control options (multiple selections possible)

Room temperature control with presence detection No

Room temperature control with open window detection No

Room temperature control with distance control option Yes

Room temperature control with adaptive start control No

Room temperature control with working time limitation No

Room temperature control with black bulb sensor No

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GENERAL SAFETY RULES

1. These heaters are for INDOOR USE ONLY.

2. DO NOT expose the heater or power cable to rain or wet conditions. Any

water entering the heater will increase the risk of electric shock. DO NOT

use this heater in a bathroom, shower room or any other wet environment.

3. NEVER locate the heater near combustible materials such as curtains,

furniture etc. Allow at least 1 metre distance.

4. DO NOT locate the heater close to an adjacent wall or low ceiling. Allow a

distance of at least 1 metre from a wall or ceiling. Avoid placing the heater

directly below power socket outlets.

5. Take care to ensure that the wire guard cannot be covered.

6. DO NOT operate heater in explosive atmospheres such as in the presence

of flammable liquids, gases or dust such as in a paint spray booth or any

explosive environment.

7. NEVER stand the heater on a movable vehicle where it could tip over.

8. DO NOT allow the halogen tubes to become covered with dust which

could become a fire hazard. If used in a dusty workplace the heater should

be cleaned as described under Cleaning and Maintenance.

9. NEVER touch the halogen tubes for at least 15 minutes after switching off.

10. DO NOT leave the heater unattended.

11. If children are present always use with a fireguard.

12. Store the heater out of the reach of children and do not allow

persons unfamiliar with these instructions to operate it.

13. Use ONLY in an upright position.

14. ALWAYS manoeuvre the heater using the handles provided and avoid

trapping the fingers between the handle and the heater body.

15. NEVER leave the heater unattended while in use. Turn off at night if

unattended.

ELECTRICAL SAFETY

1. Electrical appliances must match the power outlet. Never modify the plug

in any way. Do not use adaptor plugs with earthed (grounded) appliances.

Correct plugs and outlets will reduce the risk of electric shock.

2. Do not use this product with an extension cable.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

3. DO NOT abuse the electrical cable. Never use the cable for pulling or

unplugging the heater. Keep the cable away from sources of heat, oil,

sharp edges or moving parts. Damaged or tangled cables increase the risk

of electric shock.

4. Keep the power cable well away from machines and ensure an adequate

electrical supply is close at hand so that the operation is not restricted by

the length of the cable.

5. ALWAYS disconnect from the power supply before moving the heater or

performing any cleaning or maintenance tasks.

6. Inspect the power cable regularly for signs of damage. DO NOT use if it is

damaged, and ALWAYS keep it away from the source of heat.

7. Check the heater for damage before use. DO NOT use if the heater tubes

are damaged or broken. Any damage should be properly repaired or the

part replaced. If in doubt, DO NOT use. Consult your local Clarke dealer.

SERVICE & REPAIRS

1. If necessary, have your heater repaired by a qualified person using

identical replacement parts. This will ensure that the safety of the product is

maintained.

Please keep these instructions in a safe place for future reference.

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the obligation to

deal with the WEEE in accordance with the WEEE regulations in relation to the

treatment, recycling & recovery and environmentally sound disposal of the

WEEE.

In effect, this means that this product must not be disposed of with general

household waste. It must be disposed of according to the laws governing

Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal

facility.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTIONS

The 230v models are provided with a 13 amp BS 1363 plug, fitted with a 13amp

fuse and MUST be connected to a standard, 230 Volt (50Hz) electrical supply,

preferably through a suitably fused isolator switch.

If the plug has to be changed because it is not suitable for your socket or

because of damage, it must be removed and a replacement fitted, following

the wiring instructions shown below. The old plug must be discarded safely as

insertion into a power socket could cause an electrical hazard.

The wires in the mains lead should be

wired up in accordance with the

following colour code:

• Connect the GREEN & YELLOW

wire to the plug terminal

marked with a letter E or

• Connect the BROWN wire to the

plug terminal marked a letter

“L”.

• Connect the BLUE wire to the

plug terminal marked a letter “N”.

The fuse in the plug must be replaced with one of the same rating and this

replacement must be ASTA approved to BS1362.

We strongly recommend that this machine is connected to the mains supply

via a Residual Current Device (RCD).

If in any doubt, consult a qualified electrician. DO NOT attempt any electrical

repairs yourself.

WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY

BEFORE CONNECTING THE PRODUCT TO THE POWER SUPPLY.

WARNING: THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE

COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

BLUE = NEUTRAL BROWN = LIVE YELLOW AND GREEN = EARTH.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

UNPACKING AND ASSEMBLY

UNPACKING

When unpacking, please check contents against the following list and advise

your dealer immediately if any parts are missing.

ASSEMBLY

1. Bolt the handles to the lower frame

using the two loose bolts &

locknuts noting the orientation of

the handles.

2. Lay the heater face down and

attach the complete frame to the

heater body using the securing

knobs and the spacers located

either side of the frame tubing.

Note the order of assembly of the

handles to each side of the heater as

shown below, with particular

reference to the position of the star

washer which must be fitted against

the body of the heater.

The star washer will enable the heater to remain tilted at your chosen angle.

3. Fit the halogen tubes as described on page 11.

1 x Heater 1x Lower frame

2 x Handles 2 x Halogen tubes

1 x Fixings pack 1 x Remote control unit

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OPERATION

USING THE REMOTE CONTROL

All operations must be done using the

remote control.

• 2 x AAA batteries are required

and are installed as shown by

the diagram found inside the

remote control unit.

• The remote control must be

directed at the heater display

panel. It has a range of approx

2.5 metres and must be aimed

at the correct angle.

MANUAL OPERATION

1. Position the heater where required,

and lock the rear castor to prevent

the heater from moving. Always

move the heater using the

handles.

2. Slacken the locking knobs and

rotate the heater body to the

required angle. Tighten the

securing knobs on each side to

lock into place.

3. Connect the power cable to a

suitable power supply.

• The heater is equipped with an

anti-tilt switch that automatically cuts the power off should the

heater tip over. If this happens, stand the heater upright and it will

immediately re-set.

WARNING: FOR SAFE OPERATION OF THIS HEATER IT IS ESSENTIAL TO READ

THESE INSTRUCTIONS BEFORE USE.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

NOTE: The angle of tilt MUST NOT exceed 45 degrees downwards, as this

could lead to the heater over-heating. NEVER position the heater

pointing downwards.

4. Switch on the power at the primary switch.

• The neon indicator will illuminate.

5. Set one or both secondary switches to the I (On) position as required.

• The left one controls the upper heating element and the right one

controls the lower.

6. Press the ON/OFF button on the

remote control to switch the

elements on.

• The secondary switches will

each illuminate to show that the

heating element is in use.

• The ambient room temperature

will be displayed.

7. Set the target temperature by

pressing the + and - arrow keys on

the remote control to a value

between 15°C and 45°C.

• During normal operation the bar below the temperature display

pulsates to indicate that the heater is operating.

• When the heater has reached the target room temperature, the bar

will become solid and the heater will automatically turn off. It will

resume working when the ambient temperature falls 2oC below the

target temperature.

PROGRAMMING THE TIMER

When programming, note that the selection will only remain actively

displayed for approximately 10 seconds before reverting to the beginning of

the process. If unsure what value you wish to enter, you can maintain the

display by making constant adjustments with the +/- buttons until making your

final selection.

SETTING CURRENT TIME

1. Switch the heater on with the remote control (on/off). The heating

elements can be either on or off.

2. Press the TIME button.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

• SUN will flash repeatedly.

3. Use the left and right arrow buttons to choose a day.

4. Press the TIME button to go to the next step.

• The first 2 digits (HOUR) of the time display will flash.

5. Use the + and - buttons to scroll to the correct time (24 hr clock).

6. Press the TIME button to set the Minutes.

7. Use the + and - buttons to scroll to the minutes you require.

8. Press the TIME button to finish the time and day set up.

• The current time and day will show as a constant when the WEEK

TIMER is activated.

NOTE: The Time and Day setting will be lost and will need to be reset.

Once the heater is powered off completely, (either from the

power switch or wall supply) Follow steps 1 to 8 to reset the clock.

THE WEEK TIMER

• The Week Timer covers a 7 day week (Monday to Sunday). You can

program up to 3 individual “on/off” cycles each day.

• Each heating period can be set for a maximum of 24 hours in 10

minute increments. It is not possible for the program to span two

consecutive days e.g. Monday 10pm to Tuesday 2am.

If the user requires the heater to operate over the midnight period

they would have to set two programs, one for Monday and one for

Tuesday.

• The user can then also set two further programs for Tuesday if

required.

• Always ensure that the heating elements are switched to the ON

position when in Timer mode.

SETTING THE WEEK TIMER

SETTING THE DAY AND PROGRAM

1. Press the WEEK TIMER button on the remote control.

• Monday will start to flash.

2. Press the left and right arrow keys to select the day you want your program

to start and press the WEEK TIMER button to confirm.

• Program 1 [01] will now flash.

3. Use the + and - buttons to select the program you want to set and press the

WEEK TIMER button to confirm.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Heizung Handbücher

Clarke

Clarke DEVIL 4035 Installations- und Betriebshandbuch

Clarke

Clarke XR60DV Bedienungsanleitung

Clarke

Clarke OFR7 Bedienungsanleitung

Clarke

Clarke DEVIL 7005 Bedienungsanleitung

Clarke

Clarke 6933985 Bedienungsanleitung

Clarke

Clarke Devil 370B Series Installations- und Betriebshandbuch

Clarke

Clarke DEVIL 340 Bedienungsanleitung

Clarke

Clarke CONTRACTOR GRH30 Bedienungsanleitung

Clarke

Clarke DEVIL 350B 230V Installations- und Betriebshandbuch

Clarke

Clarke DEVIL 371PC Installations- und Betriebshandbuch

Clarke

Clarke DEVIL 7030 Bedienungsanleitung

Clarke

Clarke DEVIL 7030 Bedienungsanleitung

Clarke

Clarke DEVIL 2000PTC Bedienungsanleitung

Clarke

Clarke DEVIL 371SPD Installations- und Betriebshandbuch

Clarke

Clarke IQ2000S Stücklistenhandbuch

Clarke

Clarke OFR 9 Bedienungsanleitung

Clarke

Clarke Devil 6003 Handbuch

Clarke

Clarke CONTRACTOR GSH15 Bedienungsanleitung

Clarke

Clarke XR60 Installations- und Betriebshandbuch

Clarke

Clarke DEVIL 9000PTC Bedienungsanleitung

Clarke

Clarke DEVIL 2800PTC-B Bedienungsanleitung

Clarke

Clarke BR13/250 Bedienungsanleitung

Clarke

Clarke DEVIL 370SPD Installations- und Betriebshandbuch

Clarke

Clarke 6933980 Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung

iLO

iLO IHP2424 Betriebsanleitung