Clarke GH1 Bedienungsanleitung
GREENHOUSE HEATERS
OPERATING INSTRUCTIONS
Model Nos. GH1 & GH2
0100
Thank you for purchasing this CLARKE Greenhouse Heater
Please read this leaflet thoroughly and follow the instructions carefully, in doing so you will
ensure the safety of yourself and that of others around you, and you can look forward to the
Heater giving you long and satisfactory service.
GUARANTEE
This CLARKE product is guaranteed against faulty manufacture for a period of 12 months
from the date of purchase. Please keep your receipt as proof of purchase. This guarantee
is invalid if the product is found to have been abused or tampered with in any way, or not
used for the purpose for which it was intended.
Faulty goods should be returned to their place of purchase, no product can be returned to
us without prior permission.
This guarantee does not effect your statutory rights.
ASSEMBLY
Attach the the chimney/s to the top heater plate using the self-tapping screws provided.
IMPORTANT:
THIS HEATER IS FOR USE IN A GREENHOUSE ONLY, AND SHOULD NOT, UNDER ANY
CIRCUMSTANCES BE USED IN A DWELLING, CONSERVATORY, WORKSHOP OR GARAGE
VENTILATION
Open the ventilators in the ridge of your greenhouse, away from the wind. Some
ventilation is very important in a greenhouse, even on cold days and nights,
otherwise the burner will be starved of oxygen and the flame will die down.
Draughts of course must be avoided. Position the heater on a flat, level floor in
such a place that accidental movement or knocking over would not be possible.
HUMIDITY
If humidity is required in the greenhouse, place a pan or tray of water near the
heater, and top-up as required. Humidity is more likely to be required in the Spring,
Summer and Autumn than in the Winter. In wintertime, it is recommended that
too much humidity should be avoided.
SAFETY PRECAUTIONS
•ALWAYSuse premium grade paraffin to BS 2869:C1 as this is the ONLY fuel
suitable for safe use of your heater.
• NEVER attempt to fill or top-up your heater whilst it is lit and never move the
heater when lit.
• ALWAYS Use a clean, dry receptacle (and funnel if used) for transferring paraffin
from the main storage to the container and ALWAYS wipe any spillages from
the outside of the container.
• DO NOT under any circumstances use a vessel that has previously contained
water, petrol or methylated spirits to store your paraffin.
HOW TO LIGHT AND MAINTAIN THE LAMP
Before lighting a new wick, or an old wick after a period of disuse, remove the
wick from the burner(s) and ensure it is dry. This is most essential because if the
wick is damp, the paraffin will not soak right up the wick evenly and the correct
flame quality will not be achieved.
Re-fit the wick(s) and allow to soak well for about 30 minutes before lighting. If
one end of the wick is coloured it is that end which should be fitted uppermost
and lit.
Always make sure that the domed top of the burner is pressed securely in position,
and that the complete burner is screwed firmly into the screwed collar on the oil
tank.
in the case of model GH2, both wicks in the burner MUST be lit.
With the chimney removed, light the wick/s. When lit, replace the chimney and,
looking through the view slots in the chimney, adjust the flame height to about ¼
inch above the brass dome of the burner.
As the burner warms up, the flame height will increase, so it is important to adjust
the flame to a final height of about ½ inch - after 15 minutes or so.
Avoid the temptation to turn the wicks up too high thinking that a higher
temperature will be the result.....this will not be the case and the extreme result
will be that the wicks will give off excessive fumes and soot.
The appropriate heat will be achieved by setting the wicks as described above.
To extinguish the flames, use the extinguisher lever on the burner by pressing firmly
downwards.
At no time whilst the heater is lit or just extinguished should the chimney or top be
touched as it will be very hot and could inflict severe burns. The heater is designed
to get hot in order to be an efficient from of greenhouse heating.
Before re-lighting the heater, pull the extinguisher lever back up to expose the
wicks.
Always keep the burner perfectly clean, and remove any loose char that gathers
on the burner and wicks. Do not use scissors to trim the wicks.
Maximum efficiency of your heater will be obtained by following these simple
rules.
Always keep the container well supplied with paraffin to ensure that the wicks are
well immersed, otherwise the wicks will be starved of paraffin and the flame will
die down. Before bringing the heater into use at the beginning of a new season,
always clean out and thoroughly dry the container.
PARAFFIN
Remember to stock spare paraffin in a separate store.
SPARE PARTS
The following parts are available from your Clarke dealer:
1. Eltex Wick (2pcs) .................... BRES444
2. Brass Burner (single) ............... BRES821
3. Filler Cap ................................. BRES000
For Spare Parts and Servicing, please contact your nearest dealer, or
CLARKE International, on one of the following numbers.
PARTS & SERVICE TEL: 020 8988 7400
PARTS & SERVICE FAX: 020 8558 3622
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Clarke Heizung Handbücher
Clarke
Clarke DEVIL 7030 Bedienungsanleitung
Clarke
Clarke DEVIL 371SPC Installations- und Betriebshandbuch
Clarke
Clarke 6933985 Bedienungsanleitung
Clarke
Clarke XR60 Installations- und Betriebshandbuch
Clarke
Clarke DEVIL 2000PTC-B Bedienungsanleitung
Clarke
Clarke DEVIL 2800PTC-B Bedienungsanleitung
Clarke
Clarke DEVIL 4040 Bedienungsanleitung
Clarke
Clarke DEVIL 350C Installations- und Betriebshandbuch
Clarke
Clarke DEVIL 7003 Bedienungsanleitung
Clarke
Clarke DEVIL 4035 Installations- und Betriebshandbuch
Clarke
Clarke DEVIL 370PD Installations- und Betriebshandbuch
Clarke
Clarke DEVIL 370PC Installations- und Betriebshandbuch
Clarke
Clarke DEVIL 370SPD Installations- und Betriebshandbuch
Clarke
Clarke XR60B Bedienungsanleitung
Clarke
Clarke BR13/250 Bedienungsanleitung
Clarke
Clarke IRD20 Bedienungsanleitung
Clarke
Clarke DEVIL 2000PTC Bedienungsanleitung
Clarke
Clarke DEVIL 4035 Installations- und Betriebshandbuch
Clarke
Clarke XR55 Installations- und Betriebshandbuch
Clarke
Clarke DEVIL 6025 Bedienungsanleitung
