Clarke Strong Arm CTJ1250AB Installations- und Betriebshandbuch

OPERATING & MAINTENANCE

INSTRUCTIONS GC03/13

1.25 TONNE ALUMINIUM RACING

JACK

Model No: CTJ1250AB

PART NO: 7621824

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

INTRODUCTION

Thank you for purchasing this CLARKE Aluminium Racing Jack.

Before attempting to use this product, please read this manual throughout

and follow the instructions carefully. Thoroughly familiarise yourself with this

product & its operation in order to ensure the safety of yourself and others

around you. In so doing, you can look forward to the product giving you

long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase. This guarantee is invalid if the product is found

to have been abused or tampered with in any way, or not used for it’s

intended purpose.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission. This guarantee does not effect

your statutory rights.

SPECIFICATION

Please note that details and specifications contained herein, are correct at

the time of going to print. However, CLARKE International reserve the right to

change specifications at any time without prior notice.

BA0521JTC

rebmuNtraP4281267

thgieWgk56.11

)HxWxL(snoisnemiD )eldnahtuohtiw(mm012x052x085

daoLdetaRgk0521

elddaSfothgieH

niMmm58

xaMelddaSfothgieHmm573

yticapaCpmuPliOsertil11.0

thgieHxaMotniMmorfsekortSfooN8

ekortSrepdesiaRecnatsi

D)egareva(mm63

Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]

GENERAL SAFETY PRECAUTIONS

GENERAL

1. ALWAYS read and ensure you fully understand the following precautions

and the hazards associated with this product. Do not allow anyone who

has not read these instructions to use the jack.

2. Only use this jack for its intended purpose.

3. NEVER carry out any modifications to this product. If experiencing difficulty

of any kind consult your local dealer.

WORK AREA

1. NEVER use the jack on sloping surfaces, only on level ground. The jack

may move away slightly as soon as the tyre leaves the ground.

2. DO NOT start the vehicle engine with the jack in use.

3. This jack is for lifting only. Do not move a load using the jack as a dolly.

4. Ensure the load is taken by the full saddle and that the point of lift on the

vehicle is strong enough to support the full weight adequately.

5. Never allow children or bystanders in the area while the jack is in use.

6. NEVER work underneath a vehicle supported only by this jack. If working

under a vehicle, always use stands designed for the purpose.

7. Ensure the jack is on a firm solid base and that there is no likelihood of it

slipping when under load.

8. Ensure that all personnel are well clear of a load being raised or lowered.

SERVICING & REPAIRS

1. Check the jack for damage before use and do not use if damaged. If in

doubt, DO NOT use. Consult your local Clarke dealer.

2. ALWAYS use spare parts supplied by Clarke International. Using non-

standard parts could be extremely dangerous.

3. Ensure that the jack is properly maintained at all times and that no

corrosion or other damage is allowed to weaken any part of it.

4. When necessary, have your jack serviced or repaired by a qualified

technician using identical replacement parts. This will ensure that the

safety of the jack is maintained.

5. NEVER use the jack if it has been subjected to excess load (over 1250 kg).

The jack should be removed from service immediately and fully inspected

by qualified personnel and passed as serviceable before further use.

Please keep these instructions in a safe place for future reference.

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

UNPACKING AND ASSEMBLY

1. Remove the retaining clip by

pressing the handle mounting

downwards and releasing the clip

from the base of the jack and

from the handle opening.

2. Undo the thumbscrew until the

lower handle can be inserted fully

into the handle socket.

• The handle has a groove which

should engage with the thumb

screw once it is re-tightened.

3. Re-tighten the thumb screw to

secure the lower handle.

4. Add the upper handle by pushing

it onto the lower handle until the

ball and socket of the handle

sections snap together.

OPERATION

Before use, visually inspect the jack for oil leaks or any other sign of damage.

Should any be apparent, have the jack inspected and repaired by a

qualified technician before use.

Ensure the vehicle to be raised is chocked and standing on firm, level ground

before manoeuvring the jack so that the saddle is directly beneath the lifting

point. Consult the vehicle handbook to determine the suitable lifting points.

USING THE JACK

1. Turn the handle fully clockwise to close the release valve, and pump the

handle to raise the saddle until it reaches the vehicle lifting point.

2. Ensure that the saddle is directly below the lifting point and there are no

obstructions to prevent a clean lift. Keep all personnel at a safe distance

before continuing to pump the handle to raise the vehicle.

NOTE: The jack may move slightly during operation. It is important

therefore, that the floor is clean and completely free from debris.

3. Position axle stands directly beneath suitable supporting points under the

vehicle, before very gently twisting the handle anticlockwise.

Thumb

Screw

Groove

Retaining

Clip

Spring-Loaded Ball

Socket

Handle

Mounting

Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]

• This will open the release valve to lower the vehicle onto the stands. To

stop it lowering, turn the handle clockwise again. Always avoid a rapid

descent by turning the handle slowly.

4. Carefully lower the vehicle onto the axle stand, checking constantly,

preferably with an assistant, that the vehicles supporting point rests snugly

and cleanly on the axle stand, and that the stand is stable before all the

weight is taken.

NOTE: Ensure this operation is carried out under complete control. Do

not allow the load to drop suddenly as this could damage

internal components.

5. Completely remove the jack from the vehicle.

WARNING! NEVER WORK ON THE VEHICLE WHEN SUPPORTED ONLY BY A

JACK. THIS IS A HIGHLY DANGEROUS PRACTICE. THE VEHICLE MUST BE

SUPPORTED ON AXLE STANDS, OR SUITABLE SUPPORTS, BENEATH THE

JACKING/SUPPORT POINTS RECOMMENDED BY THE VEHICLE

MANUFACTURER. THERE SHOULD BE NO LOAD ON THE JACK.

MAINTENANCE

PURGING AIR FROM THE SYSTEM

If air bubbles become trapped inside the hydraulic system, the efficiency of

the jack will be reduced and it may not fully support the vehicle weight. Any

air can be purged from the system as follows.

1. Turn the handle anti-clockwise to

allow oil to circulate freely around

the system. Remove the filler plug.

2. Pump the handle several times to

purge air from the system.

3. Replace the filler plug, then turn

the handle clockwise and test the

jack. If efficiency is still low, check

the oil level as below.

CHECKING THE OIL LEVEL

If the jack has been stored for long periods, check for oil leaks before use. If

necessary, check the oil level as follows:

1. Ensure the jack is fully lowered by turning the handle fully anti-clockwise.

2. Remove the oil filler plug on the top of the ram assembly. A broad-bladed

screwdriver is required.

Safety Valve

Filler/drain plug

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

• The oil should be almost level with the bottom of the oil filler hole.

• Oil can be topped up using Clarke Hydraulic Oil: P/No. 3050830 for 1 litre.

OIL REPLACEMENT

1. With the jack lowered, remove the filler plug as above. Tilt the jack onto its

side and drain the old oil into a container.

2. Return the jack upright and refill with hydraulic oil up to the lower rim of

the filler hole.

3. Purge any air from the system and replace the filler plug.

4. Dispose of old oil appropriately and be sure to wipe up any spillage.

GENERAL CARE

1. Periodically lubricate the hinges, front roller and rear castors with a light oil.

2. Store in a dry location with the arm in its lowest position.

3. In the event of damage or broken components, replacements are

available from Clarke Parts & Service.

TROUBLESHOOTING

MELBORP ESUAC NOITULOS

ehtotesiartonlliwkcaJ

.thgiehlluf

.levelliowoLfipupotdnaegakaelrofkcehC

.gulplioehtaivderiuqer

.rednilycni

riAmorfriaegrupoteldnahpmuP

.metsys

.nrowsgnir-OrofrelaedekralCruoyotnruteR

.luahrevo

ehtdlohtonlliwkcaJ

.da

tonevlavesaeleR

.desolcylthgit

.yllufgnisolcsievlavkcehC

tonevlavesaeleR

.gnitaes

rofrelaedekralCruoyotn

ruteR

.luahrevo

.rednilycniriAmorfriaegrupoteldnahpmuP

.metsys

rewoltonseodkcaJ

sievlavehtnehw

.denepo

dellif

revorednilyC

.liohtiw

.lioevissecxeffoniarD

mratovipronotsiP

.gnidnibrotneb

rofrelaedekralCruoyotnruteR

.ri

aper

rodetcennocsiD

.gnirpsnruternekorb

rofrelaedekralCruoyotnruteR

.riaper

stnenopmocdegniH

.yleerfgnivomt

.stniojdegnihetacirbuL

nehwygnopssleefkcaJ

.gnitfil

.metsysnideppartriAmorfriaegrupoteldnahpmuP

.metsys

Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]

RAM COMPONENT PARTS

When requesting replacement parts, please quote the prefix:

HA-CTJ1250AB, followed by the number listed above.

ENVIRONMENTAL PROTECTION

One of the most damaging sources of environmental pollution are oil

products. Never throw away used hydraulic oil with domestic refuse or

flush it down a sink or drain. Collect all the hydraulic oil in a leak proof

container and take it to your local waste disposal site.

If disposing of this product or any damaged components, do not dispose of

with general waste. This product contains valuable raw materials and should

be taken to your local civic amenity site for recycling of metal products.

oN NOITPIRCSED ytQ oN NOITPIRCSED ytQ

1gniRlaeSmottoB161mm51gniRgniniateR1

2riovreseR171notsiPpmuP1

38.1x3.54gniR-O18152.1x02x6.01gnirgniniateR1

455.3x5.42

gniR-O19156.2x2.01gniR-O1

5tuNpoT102rednilyC1

6doRnotsiP112gniRlaeSreppoCrednilyC1

7mm52gniRgniniateR1225llaBleetS1

8esaBdoRn

otsiP1328.1x8.6gniR-O1

9rehsaW142tnioJ-U1

016.4x5.02gniR-O152wercSrevoCevlaVfeileR1

11redloHliO1622x5.9x51gniRlaeS1

21gniRgnilaeS172wercSteSevlaVfeileR1

31esaBciluardyH182gnirpSevlaVfeileR1

41gnirpS192esaBgnirpS1

51esaBgnirpS1034llaBleetS1

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

RAM COMPONENT PARTS

Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]

FRAME COMPONENT PARTS

When requesting replacement parts, please quote the prefix:

HA-CTJ1250AB, followed by the number listed above.

oN NOITPIRCSED ytQ oN NOITPIRCSED ytQ

1daPelddaS151rehsaW2

2wercSgnixiFelddaS161rotsaCleviwS2

3elddaS17101MtuN2

4mrAediS281kcolBgnitcennoC1

5rehsaWgnirpS291gnirpSnr

uteR2

6wercSdaeHtekcoS202ylbmessApmuP1

7eldnaHediS212leviwSlortnoC1

8etalPediS222eldnaHreppU1

9wercSdaeHtekcoS232eldnaHrewoL1

1rehsaWgnirpS242ekoY1

1152x01MwercSdaeHtekcoS652wercSbmuhT1

2101rehsaWgnirpS662mrAgnitfiLniaM1

3161x8MwercSdaeHtekcoS272eve

elSevitcetorP1

41rehsaWgnirpS2

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

FRAME COMPONENT PARTS

Inhaltsverzeichnis

Andere Clarke Jack Handbücher

Clarke

Clarke Strong-Arm CTJ2250LP Bedienungsanleitung

Clarke

Clarke Strong-Arm CTJ2500QLP Bedienungsanleitung

Clarke

Clarke CFTJ500 Fehlerbehebungshandbuch

Clarke

Clarke CTJ3QLGB Bedienungsanleitung

Clarke

Clarke CTJ1800AB Bedienungsanleitung

Clarke

Clarke STRONG-ARM CML3 Kurzanleitung

Clarke

Clarke STRONG-ARM CTJ2GLC Bedienungsanleitung

Clarke

Clarke STRONG-ARM CFJ48B Bedienungsanleitung

Clarke

Clarke CTJ1800A Bedienungsanleitung

Clarke

Clarke CTJ2000LP Bedienungsanleitung

Clarke

Clarke STRONG-ARM VPJ300 Bedienungsanleitung

Clarke

Clarke Strong Arm CTJ3000GB Bedienungsanleitung

Clarke

Clarke STRONG-ARM CTJ3000G Bedienungsanleitung

Clarke

Clarke Strong-Arm CTJ2CBB Bedienungsanleitung

Clarke

Clarke CFJ60 Bedienungsanleitung

Clarke

Clarke CTT320 Bedienungsanleitung

Clarke

Clarke STRONG-ARM CTJ3000QLB Bedienungsanleitung

Clarke

Clarke Strong-Arm CTJ1500QULP Bedienungsanleitung

Clarke

Clarke CTBJ5 Fehlerbehebungshandbuch

Clarke

Clarke Strong-Arm CTJ5GLS Bedienungsanleitung

Clarke

Clarke CTJ10GLS Bedienungsanleitung

Clarke

Clarke CBJ32 Bedienungsanleitung

Clarke

Clarke STRONG-ARM CTJ1500QL Installations- und Betriebshandbuch

Clarke

Clarke STRONG-ARM CTJ5GLB Bedienungsanleitung

Beliebte Jack Handbücher anderer Marken

Omega Lift Equipment

Omega Lift Equipment 18122C Gebrauchsanweisung

Pittsburgh

Pittsburgh 58816 Montageanleitung

Unimec

Unimec TP Bedienungsanleitung

Sonic

Sonic 4800703 Bedienungsanleitung

BGS technic

BGS technic 70039 Bedienungsanleitung

TradeQuip

TradeQuip 1128T Bedienungsanleitung

VEVOR

VEVOR TJD-12000SP-F Bedienungsanleitung

ULTIMATE SPEED

ULTIMATE SPEED URW 2 A1 HYDRAULIC TROLLEY JACK Bedienungsanleitung

Stels

Stels 51131 Bedienungsanleitung

Valex

Valex 1650520 Bedienungsanleitung

Pfaff

Pfaff Merkur M0 Bedienungsanleitung

Beta

Beta 3050/K Beilage

Sealey

Sealey 1050CXHV Bedienungsanleitung

Jung

Jung JH Series Bedienungsanleitung

URIAH

URIAH UC200020 Bedienungsanleitung

Kennedy

Kennedy KSJ010 Bedienungsanleitung

Grizzly

Grizzly H8097 Bedienungsanleitung

SW-Stahl

SW-Stahl 20700L Bedienungsanleitung