Clarke CAT209 Installations- und Betriebshandbuch

OPERATING & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC1019 - ISS 1

AIR BLOW GUN

MODEL NO: CAT209

PART NO: 3120526

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Blow Gun with rubber tip.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

Please keep these instructions in a safe place for future reference.

SPECIFICATION

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not affect your statutory rights.

Dimensions (L x W x H) 236 x 21 x 90 mm

Weight 116 g

Max Operating Pressure 90 psi (6.2 bar)

Air Inlet Size 1/4“BSP Female

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

COMPRESSED AIR REQUIREMENTS

Use only clean, dry, regulated compressed air as a power source.

Air compressors used with the tool must comply with the appropriate

European Community Safety Directives.

A build-up of moisture or oil in the air compressor will accelerate wear and

corrosion in the tool. Ensure any moisture is drained from the compressor daily

and the inlet filter is kept clean.

If an unusually long air hose is required, (over 8 metres), the line pressure or the

hose inside diameter may need to be increased.

The air hose must be rated at least 150% of the maximum operating pressure of

the tool.

A typical air line layout is shown above. If an automatic in-line filter/regulator is

used, it will keep the tool in good condition, but should be regularly checked.

For optimum performance it is recommended that a 3/8” ID hose is used.

DO NOT exceed the maximum operating pressure for the tool. It is

recommended that air pressure to this tool does not exceed 90 psi (6.2 bar) at

the tool. Higher pressure and dirty air will shorten the life of the tool due to

faster wear and is a possible safety hazard

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU

ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF

COMPRESSORS AND COMPRESSED AIR SUPPLY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GENERAL SAFETY RULES

WORK ENVIRONMENT

1. Keep the work area clean and tidy.

2. Dress appropriately - Do not wear loose clothing or jewellery. Tie long hair

out of the way.

3. Keep children and visitors away - Do not let children handle the blow gun.

4. DO NOT operate the blow gun where there are flammable liquids or gases.

USE OF AIR POWERED TOOLS

1. Stay alert and use common sense - do not operate this blow gun when you

are tired or under the influence of alcohol, drugs or medication.

2. ALWAYS wear eye protectors when using the blow gun. Eye protectors must

provide protection from flying particles from the front and the side.

3. DO NOT use the blow gun when other persons or animals are nearby or

may be hit by flying debris caused by the blow gun.

4. DO NOT overreach - Keep proper footing and balance at all times.

5. DO NOT use oxygen, CO2, combustible gasses or any type of bottled gas

as a source of power.

6. DO NOT connect the air supply hose with your finger on the trigger.

7. DO NOT exceed the maximum pressure for the blow gun of 90 psi / 6.2 bar.

8. Keep the air supply hose away from heat, oil and sharp edges.

9. DO NOT fit the blow gun to any stand or clamping device that may

damage it.

10. Check air hoses for leaks or worn condition before use and ensure that all

connections are secure.

11. DO NOT use for any purpose than that described in this manual.

12. DO NOT discharge this blow gun at any persons or animals.

13. DO NOT insert into any part of yours or anyone elses body.

14. DO NOT point directly at a person’s skin or at a fire.

CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN

PERSONAL INJURY AND/OR DAMAGE TO PROPERTY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

15. DO NOT carry out any alterations or modifications to the blow gun.

16. Always disconnect from the air supply when performing any maintenance.

17. DO NOT use an air tool if it is defective or operating abnormally.

18. ALWAYS maintain an air tool with care. Keep it clean for the best and safest

performance.

19. DO NOT carry the blow gun by the air hose or with your finger on the

trigger.

20. When not in use the blow gun must be disconnected from the air supply

and stored in a dry place out of the reach of children.

BEFORE USE

CONNECTING THE AIRLINE

Ensure the air supply is isolated from

the airline at a shut-off valve.

1. Connect a suitable hose to the air

inlet connector as shown.

2. Connect the other end of the air

hose to the air compressor.

3. Set the compressed air pressure to

suit the task at the airline regulator.

4. Turn on the air supply and check

for air leaks. Rectify any found before proceeding.

• PTFE tape may be useful for sealing threaded connections.

5. Your blow gun is now ready for use.

• You can fit a whip hose with a quick fit coupling if required, available

from your CLARKE dealer.

DISCONNECTING THE AIR SUPPLY

1. DO NOT disconnect the air hose until the supply is isolated at a shut-off

valve.

2. Once the pressure has been isolated, disconnect the air supply hose from

the blow gun.

3. Shut down the compressor at the end of the work session.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

MAINTENANCE

1. Before use, drain any condensate from the airline filter and compressor.

2. Clean thoroughly after use with a suitable solvent.

PERFORMANCE

Please note that factors other than the blow gun may effect its operation and

efficiency such as reduced compressor output, excessive drain on the airline,

moisture or restrictions in the air-line, or the use of connectors of improper size

or poor condition which will reduce air supply.

Your blow gun has been designed to give long and trouble free service. If,

however, having followed the instructions in this booklet carefully, you

encounter problems, take the item to your local CLARKE dealer.

Avoid storing the blow gun where the temperature is below 0oC.

ACCESSORIES

A wide range of accessories is available including filter/regulators, lubricators,

high-pressure hoses (5 to 50 metres) etc.

Contact your CLARKE dealer for further information or the CLARKE

International Service Department.

WARNING: MAKE SURE THAT THE BLOW GUN IS DISCONNECTED FROM THE

AIR SUPPLY BEFORE STARTING ANY CLEANING OR MAINTENANCE

PROCEDURES.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

COMPONENT PARTS

No Description No Description

1 Main housing 6 Spring

2 Air inlet 7 Trigger

3Nut 8Pin

4 O-ring 9 Air nozzle

5 Valve stem 10 Rubber tip

Inhaltsverzeichnis

Andere Clarke Elektrowerkzeuge Handbücher

Clarke

Clarke CAT52 Installations- und Betriebshandbuch

Clarke

Clarke Strong-Arm ARBOR PRESS Series Bedienungsanleitung

Clarke

Clarke CONTRACTOR CON1450WC Fehlerbehebungshandbuch

Clarke

Clarke STRONG-ARM CSA10BB Bedienungsanleitung

Clarke

Clarke SB30 Bedienungsanleitung

Clarke

Clarke CCRT266 Bedienungsanleitung

Clarke

Clarke CHG2000B Bedienungsanleitung

Clarke

Clarke Air CAT232 Installations- und Betriebshandbuch

Clarke

Clarke CAT115 Bedienungsanleitung

Clarke

Clarke CPR2 Installations- und Betriebshandbuch

Clarke

Clarke CBS16 Bedienungsanleitung

Clarke

Clarke DU8 Bedienungsanleitung

Clarke

Clarke CWS200 Bedienungsanleitung

Clarke

Clarke STRONG-ARM CSA50FP Fehlerbehebungshandbuch

Clarke

Clarke Woodworker CJS1-C Installations- und Betriebshandbuch

Clarke

Clarke X-Pro CAT213 Installations- und Betriebshandbuch

Clarke

Clarke Woodworker CJS2 Installations- und Betriebshandbuch

Clarke

Clarke METALWORKER CBS20 Bedienungsanleitung

Clarke

Clarke STRONG-ARM CSA4B Bedienungsanleitung

Clarke

Clarke Strong-Arm CSA30FPB Bedienungsanleitung

Clarke

Clarke Metalworker CDP350V Installations- und Betriebshandbuch

Clarke

Clarke Contractor CON750 Bedienungsanleitung

Clarke

Clarke Woodworker CBM1-C Installations- und Betriebshandbuch

Clarke

Clarke X-Pro CAT205 Installations- und Betriebshandbuch

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch

Silca

Silca MARKER 2000 Bedienungsanleitung