Clarke CPSB1 Bedienungsanleitung
OPERATION & MAINTENANCE
INSTRUCTIONS
LS0509
PORTABLE SANDBLASTER HOPPER KIT
MODEL NO: CPSB1
PART NO: 7640125
2
INTRODUCTION
Thank you for purchasing this Clarke Portable Sandblaster Hopper Kit.
Before you try to use this product, read this manual and follow the instructions
carefully. In doing so you will ensure your safety and the safety of others
around you. You can also look forward to a purchase that gives you long and
satisfactory service.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
PARTS AND SERVICING
For Parts & Servicing, please contact your nearest dealer, or
CLARKE International, on one of the following numbers.
PARTS & SERVICE TEL: 020 8988 7400
PARTS & SERVICE FAX: 020 8558 3622
or e-mail as follows:
PARTS: [email protected]
SERVICE: Service@clarkeinternational.com
3
GENERAL SAFETY RULES
1. Read this instruction manual before connecting the sandblaster to a compressor.
2. Safety glasses, hood, long-sleeve shirt, gloves and a respirator must be worn during
operation and clean up.
3. During operation, do not expose the hands or skin to the blasted material, keep
hands away from the nozzle.
4. Everyone in the blasting area must also wear personal protective equipment.
5. Check the condition of hoses and air lines before each use.
6. Make sure all connections are secure before use.
7. Abrasives used in this unit may be covered by COSHH Regulations.
8. ALWAYS make sure there is adequate ventilation. Do not spray in confined areas.
9. ALWAYS disconnect the gun from the air supply when the sandblaster is not in use.
10. ALWAYS clean the gun thoroughly after use. See ‘Maintenance’
11. ALWAYS turn off the compressor and expel all air from the air hose and gun before
disconnecting the sandblasting gun.
12. ALWAYS use appropriate air hoses and couplings and ensure that they are in good
condition. If any parts are worn or damaged, they should be replaced immediately.
13. ALWAYS hold the tool firmly and maintain good balance.
14. NEVER carry the gun by the hose. Keep hoses away from heat, oil and sharp edges.
15. NEVER use wet or even damp grit. Ensure the grit is completely dry,
16. In the case of injury seek expert medical advice immediately.
17. NEVER allow unauthorised persons or children use or play with the sandblaster.
18. Do not use the sandblaster around animals.
Warning: Compressed air can be dangerous. Ensure that you are
thoroughly familiar with all precautions relating to the use of
compressors and compressed air supplies.
Warning: Disconnect the sandblaster from the air supply before
performing any maintenance.
Warning: Do not point the sandblaster gun at anyone or objects other
than the intended work object.
4
PART IDENTIFICATION
Unpack your sandblaster, should there be any damage caused during transit
contact your Clarke dealer immediately.
Delivery Hose
Sandblasting Gun
Hopper Hook
Hook
Handle
Please dispose of any packaging responsibly. The cardboard packaging can
be recycled.
5
OPERATION
USING YOUR SANDBLASTER
The compressor used must be at least 3hp and capable of supplying a
minimum of 10 CFM of air
1.
FIG 1
Connect an air hose (sold
separately) from your compressor,
to the hose fitting on the
sandblasting gun. Fig 1.
• Set the air pressure on your air
compressor to 100 -150 psi.
2.
FIG 2
Make sure air hole located on the
base of the hopper is not
covered. Fig 2.
3. Pour the blasting medium into the
hopper.
4. Start compressor according to the
manufacturers instructions.
5. Check for leaks along all hoses
and fittings. if leaks are found, turn
off the compressor, disconnect
the hose and repair immediately.
6. Point the sandblasting gun in a safe direction away from people, pets or
anything around you that may be damaged by direct or indirect abrasive
spray.
7. Press and hold the sandblasting gun trigger until abrasive medium is flowing
through the nozzle.
TO STOP BLASTING
1. Release the trigger on the sandblasting gun.
6
SPECIFICATIONS
CPSB1
Sand Grade Type Up to 60 Grit (Clarke AOP60)
Abrasive Material Aluminium Oxide, Garnet Powder,
Glass Bead
Sand Capacity: (kg/lbs) 22.7/50
Operating Pressure: (psi) 100-150
Minimum Flow Rate Req: (cfm) 10
Compressor Size Hp: (Minimum) 3
Air Fitting: 1/4” NPS
Dimensions (Length x Width x Height) 490 mm x 430 mm x 895 mm
Weight 2 kg
7
NOTES
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Clarke Elektrowerkzeuge Handbücher
Clarke
Clarke CPSB100 Bedienungsanleitung
Clarke
Clarke Woodworker CJS2 Installations- und Betriebshandbuch
Clarke
Clarke STRONG-ARM CSA50FP Fehlerbehebungshandbuch
Clarke
Clarke CHT879 Bedienungsanleitung
Clarke
Clarke X-Pro CAT202 Installations- und Betriebshandbuch
Clarke
Clarke CAT51 Installations- und Betriebshandbuch
Clarke
Clarke CIR450B Installations- und Betriebshandbuch
Clarke
Clarke CSA20FBT Bedienungsanleitung
Clarke
Clarke CPS125 Bedienungsanleitung
Clarke
Clarke CAT115 Bedienungsanleitung
Clarke
Clarke X-Pro CAT205 Installations- und Betriebshandbuch
Clarke
Clarke CHT 459 Bedienungsanleitung
Clarke
Clarke Woodworker CBM1-C Installations- und Betriebshandbuch
Clarke
Clarke CDP10B Installations- und Betriebshandbuch
Clarke
Clarke CAT211 Installations- und Betriebshandbuch
Clarke
Clarke COEBS1 Bedienungsanleitung
Clarke
Clarke METALWORKER CMPS1 Bedienungsanleitung
Clarke
Clarke CAT52 Installations- und Betriebshandbuch
Clarke
Clarke Strong-Arm CSA30FPB Bedienungsanleitung
Clarke
Clarke cp185 Installations- und Betriebshandbuch
