Clarke DHC-2 Bedienungsanleitung

OPERATION & MAINTENANCE

INSTRUCTIONS

LS0609

DOUBLE HEADED METAL NIBBLER

MODEL NO: DHC-2

PART NO: 6500233

INTRODUCTION

Thank you for purchasing this CLARKE Double Headed Metal

Nibbler.

Before attempting to use this product, please read this manual

thoroughly and follow the instructions carefully. In doing so you

will ensure the safety of yourself and that of others around you,

and you can look forward to your purchase giving you long and

satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a

period of 12 months from the date of purchase. Please keep

your receipt which will be required as proof of purchase.

This guarantee is invalid if the product is found to have been

abused or tampered with in any way, or not used for the

purpose for which it was intended.

Faulty goods should be returned to their place of purchase, no

product can be returned to us without prior permission.

This guarantee does not effect your statutory rights.

CUTTING CAPACITY

MATERIAL MAXIMUM CUTTING CAPACITY

Steel plate 1.8 mm

Stainless steel plate 1.2 mm

Copper/aluminium 2 mm

Plastic fibre board 2 mm

SAFETY WARNINGS

The term ‘Power tool’ in the

safety warnings refers to any

electric / battery or pneumatic

drill, required to use this nibbler.

WORK AREA SAFETY

1. Keep work area clean and

well lit. Cluttered and dark

areas invite accidents.

2. Do not operate power tools in

explosive atmospheres, such

as in the presence of

flammable liquids, gases or

dust. Power tools create

sparks which may ignite the

dust or fumes.

3. Keep children and bystanders

away while operating a power

tool. Distractions can cause

you to lose control.

ELECTRICAL SAFETY

1. Avoid body contact with

earthed or grounded surfaces

such as pipes, radiators,

ranges and refrigerators. There

is an increased risk of electric

shock if your body is earthed

or grounded.

2. Do not expose power tools to

rain or wet conditions. Water

entering a power tool will

increase the risk of electric

shock.

PERSONAL SAFETY

1. Stay alert, watch what you are

doing and use common sense

when operating a power tool.

Do not use a power tool while

you are tired or under the

influence of drugs, alcohol or

medication. A moment of

inattention while operating

power tools may result in

serious personal injury.

2. Use safety equipment. Always

wear eye protection. Safety

equipment such as dust mask,

non-skid safety shoes, hard hat,

or hearing protection used for

appropriate conditions will

reduce personal injuries.

3. Remove any adjusting key or

wrench before turning the

power tool on. A wrench or a

key left attached to a rotating

part of the power tool may

result in personal injury.

4. Do not overreach. Keep proper

footing and balance at all

times. This enables better

control of the power tool in

unexpected situations.

5. Dress properly. Do not wear

loose clothing or jewellery.

Keep your hair, clothing and

gloves away from moving

parts. Loose clothes, jewellery

or long hair can be caught in

moving parts.

POWER TOOL USE AND CARE

1. Do not force the power tool.

Use the correct power tool for

your application. The correct

power tool will do the job

better and safer at the rate for

which it was designed.

2. Do not use the power tool if the

switch does not turn it on and

off. Any power tool that cannot

be controlled with the switch is

dangerous and must be

repaired.

3. Store idle power tools out of the

reach of children. Power tools

are dangerous in the hands of

untrained users.

PARTS IDENTIFICATION

No Description

1Double ended cutter

2Cutter guide (2 Fitted + 1 Spare)

3Wrench

4Plastic Handle

5Double Headed Metal Nibbler

BEFORE USE

FITTING THE HANDLE TO THE METAL NIBBLER

Fig. 1

Screw the handle over one

of the cutter guides as

shown

FITTING THE METAL NIBBLER TO THE DRILL

Fig. 2

Slide the nibbler drive

spindle into the drill.

• The drill should have a

speed rating of 1500-

3000 rpm.

2. Tighten the drill chuck.

LOCKING/LOOSENING THE CUTTER GUIDE

Turn the cutter guide locking

bolt clockwise to lock the

cutter guide into position

and anticlockwise to allow

the cutter guide to rotate

freely.

• For straight cuts, lock

the cutter guide into

position.

• For curved cuts allow the cutter guide to rotate freely.

Only loosen the cutter guide locking bolt enough to allow the cutter

guide to rotate freely, if you loosen it too much the cutter guide will fall

off.

Fig. 3

OPERATION

• Apply the metal nibbler to the workpiece only when

running at full speed.

• Always hold the

metal nibbler

vertical to the

surface of the steel

sheet and without

tilting. The cut takes

place during the

upward motion of

the metal nibbler.

• Guide the metal nibbler evenly and with moderate

feed pressure in the cutting direction.

• Do not exert force, otherwise the metal nibbler and

cutter guide will become damaged.

USING THE METAL NIBBLER

• Straight cuts are carried out best when the metal

nibbler is guided alongside a ruler/straight edge.

• Contours can be cut by guiding the metal nibbler along

a curved template.

• For inside cuts, you will need to pre-drill a 10 mm hole.

CHANGING THE CUTTER GUIDE

Fig. 5

Remove cutter guide fixing

screws using the hex key.

2. Pull the cutter guide away

from the main body.

3. Replace the cutter guide

with a new one and tighten

the fixing screw to secure.

Fig. 4

CHANGING THE CUTTER

1. Loosen the cutter guide fixing screws using the hex key.

2. Lift out the coil spring and cover shown in the picture and

loosen the fixing screw and nut.

3. Slide out the cutter.

Fig. 6

4. Replace with a new cutter and retighten the fixing screw and

nut using the hex key supplied.

• The fixing nut locks into the indentation on the cutter.

5. Replace the cover and coil spring

6. Refit the cutter guide.

Fig. 7

Inhaltsverzeichnis

Andere Clarke Elektrowerkzeuge Handbücher

Clarke

Clarke CAT113 Installationsanleitung

Clarke

Clarke Strong-Arm CSA15F Installations- und Betriebshandbuch

Clarke

Clarke Air CAT149 Installations- und Betriebshandbuch

Clarke

Clarke Air 25C Installations- und Betriebshandbuch

Clarke

Clarke CIR450B Installations- und Betriebshandbuch

Clarke

Clarke CIR18LiC Installations- und Betriebshandbuch

Clarke

Clarke CAT22B Installations- und Betriebshandbuch

Clarke

Clarke METALWORKER CMPS1 Bedienungsanleitung

Clarke

Clarke ZX-R Pro Series Bedienungsanleitung

Clarke

Clarke CAT210 Installations- und Betriebshandbuch

Clarke

Clarke CPR2 Installations- und Betriebshandbuch

Clarke

Clarke Woodworker CBM1-C Installations- und Betriebshandbuch

Clarke

Clarke STRONG-ARM CSA12F Bedienungsanleitung

Clarke

Clarke CIR450C Installations- und Betriebshandbuch

Clarke

Clarke CMFT250 Installations- und Betriebshandbuch

Clarke

Clarke Woodworker CJS2 Installations- und Betriebshandbuch

Clarke

Clarke CAT21B Installations- und Betriebshandbuch

Clarke

Clarke Strong-Arm CSA20F Bedienungsanleitung

Clarke

Clarke X-PRO CAT140 Installations- und Betriebshandbuch

Clarke

Clarke CPT1000 Bedienungsanleitung

Clarke

Clarke Air 25CN Installations- und Betriebshandbuch

Clarke

Clarke CTILG 5060287 Montageanleitung

Clarke

Clarke CDP10B Bedienungsanleitung

Clarke

Clarke Strong-Arm AHP 26 Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

Kemper

Kemper 1740PRO Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch