Clarke METALWORKER CDP401B Installations- und Betriebshandbuch

GC0110

16mm DRILL PRESS

Model Nos CDP401B & CDP451F

Part No 6505570 & 6505580

OPERATING & MAINTENANCE

INSTRUCTIONS

OPERATING & MAINTENANCE

INSTRUCTIONS

INTRODUCTION

Thank you for purchasing this CLARKE Drill Press.

Before attempting to operate the machine, it is essential that you read this

manual thoroughly and carefully follow all instructions given. In doing so you

will ensure the safety of yourself and that of others around you, and you can

also look forward to the product giving you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of

12 months from the date of purchase. Please keep your receipt as proof of

purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL PROTECTION

Do not dispose of this product with general household waste. All tools,

accessories and packaging should be sorted, taken to a recycling

centre and disposed of according to the laws governing Waste

Electrical and Electronic Equipment.

PARTS & SERVICING

For parts & servicing, please contact your nearest dealer, or

CLARKE International, on one of the following numbers.

PARTS & SERVICE TEL: 020 8988 7400

PARTS & SERVICE FAX: 020 8558 3622

or e-mail as follows:

PARTS: [email protected]

SERVICE: [email protected]

CONTENTS

Introduction ............................................................................................ 2

Guarantee .............................................................................................. 2

Environmental Protection ...................................................................... 2

Parts & Service Contacts ....................................................................... 2

General Safety Rules ............................................................................. 4

Additional Safety Rules for Drill Presses ............................................... 6

Electrical Connections .......................................................................... 7

Machine layout ...................................................................................... 8

Unpacking .............................................................................................. 9

Assembly .............................................................................................. 10

Useful Accessories ............................................................................... 14

Settings & Adjustments ........................................................................ 15

Operation ............................................................................................. 17

Machine Speed Table ......................................................................... 20

Drilling Speeds ..................................................................................... 21

Maintenance ........................................................................................ 22

Troubleshooting .................................................................................... 23

Technical Specification ....................................................................... 25

Parts List and Diagrams ....................................................................... 26

Declaration of Conformity .................................................................. 31

GENERAL SAFETY RULES

GENERAL SAFETY IN THE WORKPLACE

1. ALWAYS ensure that air can circulate around the machine and that the air

vents are unobstructed.

2. ALWAYS keep work area clean & tidy. Cluttered work areas and benches

invite accidents.

3. NEVER over-reach. Keep proper footing and balance at all times.

4. NEVER use or store equipment in a wet/damp environment or expose to

rain.

5. KEEP children and bystanders at a safe distance from work area.

6. NEVER operate a machine when under the influence of alcohol, drugs or

medication.

7. ALWAYS ensure the workplace is well lit. Ensure that lighting is placed so

that you will not be working in your own shadow.

CARE & USE OF THE EQUIPMENT

1. ALWAYS check for any damage or any condition that could affect the

operation of the machine. Any damaged part should be properly

repaired.

2. NEVER remove the cover panel unless the machine is disconnected from

the supply, and never use the machine with cover panels removed.

3. NEVER attempt any electrical or mechanical repair unless you are a

qualified technician. If you have a problem with the machine contact

your local CLARKE dealer.

4. NEVER use this product for any other purpose than that described in this

booklet.

5. NEVER abuse the mains cable by yanking the cable to disconnect it from

the socket. Keep the cable away from sharp edges/hot surfaces.

6. NEVER stand on the machine. Serious injury could occur if the machine

topples over.

7. Avoid accidental starting by making sure the power switch is off before

plugging in the power cable.

8. Never leave the machine running unattended until it has come to a

complete stop.

PROTECTIVE CLOTHING

1. Dress properly. Loose clothing, gloves, neckties, rings, bracelets, or other

jewellery may get caught in moving parts. Non-slip footwear is

recommended. Long hair should be tied back.

2. ALWAYS wear safety glasses. Everyday glasses are not safety glasses.

3. Wear a face mask if drilling into any material which produces dust.

CARE OF POWER TOOLS

1. Know your machine. Read the manual carefully. Learn the machines

applications and limitations, as well as the specific potential hazards

peculiar to it.

2. ALWAYS keep the guards in place and in working order.

3. Remove any adjusting keys or wrenches before starting. Form the habit of

checking to ensure that keys, wrenches and tools are removed from the

machine.

4. Don’t force the machine. It will do the job better and safer, at the rate for

which it was designed.

5. Use the correct tool. Don’t force a tool or attachment to do a job for

which it was not designed.

6. ALWAYS maintain tools in top condition. Keep drills sharp and clean for

best and safest performance. Follow instructions for lubricating and

changing accessories.

7. ALWAYS disconnect the machine from the power supply before carrying

out any servicing or changing of accessories.

8. CHECK for any damage before use. Damage to moving parts or major

components should be inspected by a qualified technician before

operating the machine. Contact your local dealer for advice.

WARNING: AS WITH ALL MACHINERY, THERE ARE CERTAIN HAZARDS

INVOLVED WITH THEIR OPERATION AND USE. EXERCISING RESPECT AND

CAUTION WILL CONSIDERABLY LESSEN THE RISK OF PERSONAL INJURY.

HOWEVER, IF NORMAL SAFETY PRECAUTIONS ARE OVERLOOKED, OR

IGNORED, PERSONAL INJURY TO THE OPERATOR, OR DAMAGE TO

PROPERTY MAY RESULT.

ADDITIONAL SAFETY RULES FOR DRILL PRESSES

1. IMPORTANT: You should not operate this machine unless you are

thoroughly familiar with drilling machines and drilling techniques. If there is

any doubt whatsoever you should consult a qualified person.

2. NEVER operate the machine until it is completely assembled and you

have read and understood this entire manual.

3. ALWAYS use clamps, or a drill vice bolted to the table, to hold the work. It

should never be held in bare hands.

4. ALWAYS shut off the power and remove the drill bit before leaving the

machine,

5. ALWAYS make all adjustments with the power OFF.

6. ALWAYS use the correct drilling speeds for the drill size and the type of

material being drilled (see page 21).

7. NEVER leave the drill unattended whilst it is running. Turn the machine OFF

and do not leave until it has come to a complete stop.

8. ALWAYS remove and store the drill bits when you have finished with the

machine.

9. CAUTION: This machine is designed for use with drill bits and morticing

attachments only. The use of other cutting tools or accessories could be

hazardous.

10. NEVER attempt to drill into a workpiece that does not have a flat surface

unless a suitable support is used.

11. ALWAYS stop the drill before removing workpieces, work supports or swarf

from the table.

12. ALWAYS Make sure you remove the chuck key before turning the machine

on.

13. Adjust the table or depth stop to avoid drilling into the table surface.

14. ALWAYS be sure that the drill bit is securely locked in the chuck.

15. NEVER assemble or set up any work on the table while the drill is running.

16. ALWAYS ensure the table lock is tight before starting the drill.

17. ALWAYS keep hands and fingers away from the drill bit.

WARNING: DUST GENERATED FROM CERTAIN MATERIALS CAN BE

HAZARDOUS TO YOUR HEALTH. ALWAYS OPERATE THE MACHINE IN A

WELL VENTILATED AREA. USE A DUST COLLECTION SYSTEM WHENEVER

POSSIBLE.

ELECTRICAL CONNECTIONS

Connect the mains lead to a standard, 230 Volt (50Hz) electrical supply

through an approved 13 amp BS 1363 plug, or a suitably fused isolator switch.

WARNING! THIS APPLIANCE MUST BE EARTHED

IMPORTANT: The wires in the mains lead are coloured in accordance with the

following code:

Green & Yellow .......... Earth

Blue .......... Neutral

Brown .......... Live

As the colours of the flexible lead of this appliance may not correspond with

the coloured markings identifying terminals in your plug proceed as follows:

• Connect GREEN & YELLOW cord to plug terminal marked with letter

“E” or Earth symbol “ ”, or coloured GREEN or GREEN & YELLOW.

• Connect BROWN cord to plug terminal marked letter “L” or

coloured RED.

• Connect BLUE cord to plug terminal marked letter “N” or coloured

BLACK.

If this appliance is fitted with a plug which is moulded onto the electric cable

(i.e. non-rewirable) please note:

1. The plug must be thrown away if it is cut from the electric cable. There is a

danger of electric shock if it is subsequently inserted into a socket outlet.

2. Never use the plug without the fuse cover fitted.

3. Should you wish to replace a detachable fuse carrier, ensure that the

correct replacement is used (as indicated by marking or colour code).

4. Replacement fuse covers can be obtained from your local dealer or most

electrical stockists.

5. The fuse in the plug must be replaced with one of the same rating (13

amps) and this replacement must be ASTA approved to BS1363.

MACHINE LAYOUT

UNPACKING

When unpacking, check for damage or omissions etc. Any found should be

reported to your CLARKE dealer where the machine was originally

purchased. Do not discard the packaging until the machine is assembled.

To protect the machine parts from moisture, a protective coating has been

applied to the outside surfaces. Remove this coating with a soft cloth,

moistened with kerosene. Do not use acetone, gasolene or thinners for

cleaning. Apply a coat of paste wax to the table to prevent surface

corrosion and column and then wipe all parts with a clean, dry cloth.

The machine is delivered with the following components:

A Table Assembly E Base

B Column assembly with table support F Head Assembly

C Instruction manual (this document) G Box of loose parts

D Bag of loose parts H Chuck Guard Assembly

WARNING: IF ANY PART IS MISSING OR DAMAGED, DO NOT PLUG THE

MACHINE IN UNTIL THE MISSING OR DAMAGED PART IS REPAIRED OR

REPLACED AND ASSEMBLY IS COMPLETE.

TOOLS NEEDED FOR ASSEMBLY

• Adjustable wrench or socket set

• Cross-head screwdriver

• Hammer and block of wood

INSTALLING THE BASE AND COLUMN

NOTE: Ideally, the base should be firmly bolted

to the floor or workbench, prior to assembly of

other components. The mounting surface must

flat, level and capable of supporting the ma-

chines weight. The machine should be securely

fastened through the mounting holes to a stand

or floor with heavy-duty fasteners (not supplied).

This will prevent the machine from tipping over,

sliding, or walking during operation.

1. With the base on a flat level surface, bolt on

the column using the 4 x M10 Hex head bolts

(1) provided and tighten them fully.

Fig 1

ASSEMBLY

ITEMS SUPPLIED LOOSE IN THE BAG OR BOX

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Elektrowerkzeuge Handbücher

Clarke

Clarke Metalworker CDP350V Installations- und Betriebshandbuch

Clarke

Clarke Air CAT147 Installations- und Betriebshandbuch

Clarke

Clarke Air CAT217 Installations- und Betriebshandbuch

Clarke

Clarke CWS200 Bedienungsanleitung

Clarke

Clarke CPSB100B Bedienungsanleitung

Clarke

Clarke CAT22B Installations- und Betriebshandbuch

Clarke

Clarke 6505512 Bedienungsanleitung

Clarke

Clarke CAT209 Installations- und Betriebshandbuch

Clarke

Clarke CAT113 Installationsanleitung

Clarke

Clarke CAT51 Installations- und Betriebshandbuch

Clarke

Clarke CRT 40 Bedienungsanleitung

Clarke

Clarke CAT108 Installations- und Betriebshandbuch

Clarke

Clarke CDP10B Bedienungsanleitung

Clarke

Clarke CONTRACTOR CON800 Installations- und Betriebshandbuch

Clarke

Clarke CONTRACTOR CON1450WC Fehlerbehebungshandbuch

Clarke

Clarke CMFT250 Installations- und Betriebshandbuch

Clarke

Clarke CHT674 Bedienungsanleitung

Clarke

Clarke COEBS1 Bedienungsanleitung

Clarke

Clarke X-Pro CAT199 Installations- und Betriebshandbuch

Clarke

Clarke Woodworker CJS2 Installations- und Betriebshandbuch

Clarke

Clarke CEW1000 Handbuch

Clarke

Clarke Strong-arm AHP 16 Bedienungsanleitung

Clarke

Clarke ECSS-1 Benutzerhandbuch

Clarke

Clarke CHT141 Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

Kemper

Kemper 1740PRO Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch