Classic Exhibits Gravitee GOD-1557 Handbuch

Order #XXXXX

Locked layer contains

placeholder marks.

BACK VIEWFRONT VIEW

GOD-1557 Counter

If you would like to tell us about your experience with your setup instructions please email us at [email protected]

SETUP INSTRUCTIONS

Order #XXXXX General Information

Assembly Assembly Cont’d

Side-by-Side Assembly

1) Frames: Place frames side-by-side with one higher than the

other, then slide panel down to lock panels securely together.

2) Corner Connectors: Repeat Step 1 for installing corner

connectors to frames.

Side-by-Side Disassembly

1) Pull pin lock outwards to disengage.

2) Pull frames upward and apart at the same time to detatch.

Push pin lock into hole of connecting frame.

Note: Block on pin lock will secure in groove.

Pin Lock

General Setup Instructions

- Read entire setup instruction manual prior to

unpacking parts and pieces.

- The setup instructions are created specifically

for this configuration.

- Setup instructions are laid out sequentially in

steps, including exploded views with detailed

explanation for assembly.

Cleaning & Packing

- For Cleaning Metal, Plex, & Laminate Parts:

Use a MILD NON-ABRASIVE cleanser and

soft cloth/paper towel to clean all surfaces.

- Keep exhibit components away from heat

and prolonged sun exposure.

Heat and UV exposure will warp and

fade components.

- Retain all provided Packing Materials.

All provided packing materials are for

ease of repacking & component protection.

Disassembly

- For loss prevention, tighten all set screws

and locks during disassembly.

Graphic Removal

SEG Graphic Installation

Corner A

Corner D

Corner B

Corner C

It is important to first insert graphic

into each alternate corner, then to

the sides of the frame.

If this is not done, graphic will not fit

into the frame correctly.

Step 1

Insert corner A.

Turn edge of graphic so silicon welt

is perpendicular to face of graphic.

Insert narrow side of welt with fabric

to outside into the channel.

Repeat for other side of this corner.

Step 2

Repeat Step 1 for opposite corner

C, then insert corner B, followed by

corner D, to complete the

installation of the corners.

Step 3

Once all corners are inserted, press

one silicon edge into channel from

corners and work toward the center.

Make sure welt is fully inserted into

channel. Continue until all sides are

done. Smooth out edges of graphic.

To remove the graphic from

the frame, locate the fabric

pull tab.

Gently pull up on the tab to

remove the fabric.

Step 1 of 2

Order #XXXXX

Locked layer contains

placeholder marks.

BACK VIEWBACK VIEW

Item

2,2A

Qty.

1,1

Description

37.5”h Gravitee Corner Post w/ S10 & Door Hinges

14.125”w x 38”h Gravitee panel

37.5”h Gravitee Corner Post w/ caps

38”w x 38”h Backlit Gravitee Panel

37.5”h Gravitee Corner Post w/ caps

14.125”w x 38”h Gravitee panel

37.5”h Gravitee Corner Post w/ S10 & Door Hinges

37.094”w Z45 Horizontal Extrusion

34.417”h Z45 Vertical Extrusion w/ Door Stopper

Light Panel for Gravitee Panel [4]

Steps:

1) Assemble Gravitee panels & posts together, in numerical

order as shown, making sure Velcro is facing inward.

2) Attach lower horizontal [2] between posts [1] and [7].

3) Attach vertical [3] to horizontal [2].

4) Attach upper horizontal [2A] between posts [1] and [7],

then attach vertical [3] to horizontal [2A].

5) Connect doors to posts [1] and [7]. See Door Connection detail.

6) Connect light panel to back of Gravitee panel [4].

See Light Panel detail.

Top View

Door

Light

anel

FRONT VIEW 1) Connect light strips together & attach

transformers.

2) Run power cords out hole in back of

light panel to power source.

3) Connect light panel to Velcro on back

of Gravitee panel.

Maximum 8 light strips

per transformer.

To Transformer

Light Strip Connector

Cord

Connect light strips

together, as shown.

Light to Light

Attachment

Light to Transformer

Attachment

Transformer

144W / 6 Amp / 24V

Transformers

Light Panel

Door

Hinge

Slide pin into

hinge attached

to vertical.

Slide door

hinge over pin.

Door Connection

Counter Assembly

Step 2 of 2

Order #XXXXX

Locked layer contains

placeholder marks.

Side

SEG

Wrap

Corner

Wrap

Corner

Side

SEG

Item

Qty.

Description

18”h Shelf Supports

Steps:

1) Apply SEG graphics to front and sides of counter assembly.

See General Information sheet for instruction.

2) Connect shelf supports to Velcro on inside of [2] and [6],

then place shelf onto shelf supports.

3) Lock counter top to horizontals [2] and [6].

See Counter Top Lock detail.

Completed Assembly

Counter Top

Shelf

Support

Shelf

Front SEG

Align hole with pin Rotate pin. Spring

will push pin into hole.

Counter Top Lock

Hole

FRONT VIEW

Front ViewBack View

FRONT VIEW

TOP VIEW

Counter Attachments

Andere Classic Exhibits Inneneinrichtung Handbücher

Classic Exhibits

Classic Exhibits Symphony SYK-2038 Handbuch

Classic Exhibits

Classic Exhibits SYMPHONY SYM-406B Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1235 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary designs MOD-1529 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYM-408 Handbuch

Classic Exhibits

Classic Exhibits Visionary Designs MOD-1243 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1137 Bedienungsanleitung

Classic Exhibits

Classic Exhibits GRAVITEE GOD-1559 Handbuch

Classic Exhibits

Classic Exhibits Euro LT Hybrids LTK-1119 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYM-408 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1519 Handbuch

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-1218 Bedienungsanleitung

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1556C Bedienungsanleitung

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1590 Handbuch

Classic Exhibits

Classic Exhibits SYMPHONY SYK-1025 Handbuch

Classic Exhibits

Classic Exhibits Euro LT Hybrids LTK-1108 Bedienungsanleitung

Classic Exhibits

Classic Exhibits LTK-1139 Bedienungsanleitung

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-2959 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1702 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS VK-4022 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-1030 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1109 Handbuch

Classic Exhibits

Classic Exhibits SEGUE DESIGNS MOD-1624 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-1016 Handbuch

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung

Classic Exhibits gravitee GOD-1557 Handbuch

Beliebte Inneneinrichtung Handbücher anderer Marken