Classic Exhibits SEGUE DESIGNS MOD-1624 Handbuch

Order #XXXXX

Locked layer contains

placeholder marks.

Plan View 10’

10’

MOD-1624 - 10’ x 10’ Display

If you would like to tell us about your experience with your setup instructions please email us at [email protected]

SETUP INSTRUCTIONS

Order #XXXXX

Locked layer contains

placeholder marks.

= 1 sq foot

Plan View

Order #XXXXX

DO NOT USE POWER TOOLS

ALL CONNECTIONS MUST

BE TIGHTLY SECURED

Part Identification - Numbering

Spline Connection Base Plate & Extrusion Connection

General Setup Instructions

- Read entire setup instruction manual prior to

unpacking parts and pieces.

- The setup instructions are created specifically

for this configuration.

- Setup instructions are laid out sequentially in

steps, including exploded views with detailed

explanation for assembly.

WARNING

Cleaning & Packing

- For Cleaning Metal, Plex, & Laminate Parts:

Use a MILD NON-ABRASIVE cleanser and

soft cloth/paper towel to clean all surfaces.

- Keep exhibit components away from heat

and prolonged sun exposure.

Heat and UV exposure will warp and

fade components.

- Retain all provided Packing Materials.

All provided packing materials are for

ease of repacking & component protection.

Disassembly

- For loss prevention, tighten all set screws

and locks during disassembly.

Hex Tool - Essential for Assembly

Extrusion & Lock Connection Engaged Lock

LADDERS OR LIFTS

MAY BE REQUIRED

General Information

Order #XXXXX

Straight Connection

All knobs must be tightened securely to ensure a proper connection.

Adjust connectors if necessary to

prevent gaps in connection.

Upper Horizontal Extrusion

Lower Horizontal Extrusion

Straight Connector

Corner

Connectors Corner

Connectors

Corner

Connectors Corner

Connectors

COMPLETED ASSEMBLY

3) Tighten all knobs to secure connection.

Slide verticals over

lower connectors.

Then slide upper

connectors into

groove of verticals.

Tighten all knobs.

When assembling frame, first attach all straight

connectors, then attach corner connectors.

1) Place extrusions end-to-end.

2) Loosen all knobs, then slide straight

connectors across the seam of extrusions.

Disassembly

1) Loosen all knobs.

2) Slide connectors off of one extrusion.

3) Tighten knobs to prevent loss during

packing & shipping.

CEI110 Profile

Slide both connectors across seam of extrusions.

Tighten all knobs.

Corner Connection

3) Tighten all knobs to secure connection.

Disassembly

1) Loosen knobs on vertical extrusions.

2) Slide the vertical extrusions off of

corner connectors on lower and upper

horizontal extrusions.

1) Loosen knobs, then slide vertical extrusions onto

corner connectors of lower horizontal extrusion.

2) Slide corner connectors of upper horizontal

extrusion into grooves of vertical extrusions.

Keep straight connectors in groove of

extrusion. Do not remove connectors

during disassembly.

CEI110 Frame Assembly

Order #XXXXX

Graphic Removal

To remove the graphic

the frame, locate the fabric

pull tab.Gently pull up on the

tab to remove the fabric.

Step 1

Insert corner A. Turn edge of

graphic so silicon welt is

perpendicular to face of

graphic. Insert narrow side

of welt with fabric to outside

into the channel. Repeat for

other side of this corner.

Step 2

Repeat Step 1 for opposite

corner C, then insert corner

B, followed by corner D, to

complete the installation of

the corners.

Step 3

Once all corners are inserted,

press one silicon edge into

channel from corners and

work toward the center.

Make sure welt is fully inserted

into channel. Continue until

all sides are done. Smooth

out edges of graphic.

It is important to first insert

graphic into each alternate

corner then to the sides of

the frame. If this is not done,

graphic will not fit into the

frame correctly.

Corner A

Corner D

Corner B

Corner C

from

SEG Installation

Crate 1 of 1

Order #XXXXX

Locked layer contains

placeholder marks.

CRATE PACKING

Crate Packing

Step 1 of 8

Order #XXXXX

Locked layer contains

placeholder marks.

Lig

Panel

Lig

Panel

Lig

Panel

When assembled

FRONT VIEW

Bracket

bolts

Attach bracket to

CEI110 horizontals,

using bolts &

V4 Connectors.

Bracket Connection

Set

Screw

Bolt

V4 Connector

Item

Qty.

Description

95.252”h TSP2 Vertical Extrusion

92.353”h GS310 Vertical Extrusion

2.964”w Z140 Horizontal Extrusion

2.964”w Z45 Horizontal Extrusion

2.964”w Z140 Horizontal Extrusion

Custom Bracket

96”h CEI110 Vertical Extrusion

24”w CEI110 Horizontal Extrusion

48”w CEI110 Horizontal Extrusion

17.868”w x 92.353”h Light Panel

38.882”w x 92.353”h Light Panel

Steps:

1) Assemble Corner brackets & extrusions [1] through [8] as shown in Corner Assembly detail.

2) Connect vertical [1] to horizontals [3,4] using corner connectors. Repeat step,

attaching vertial [2] to horizontals [5,6]. Refer to the CEI110 Frame Assembly

general information page.

3) Insert side Light Panels between horizontals [3,4] & [5,6].

4) Attach lower horizontals [3,7] & [5,7] to lower brackets of Corner Assemblies.

See Bracket Connection detail.

5) Insert front Light Panel between horizontals [7,8]

6) Connect upper horizontals [4,8] & [6,8] to upper brackets of Corner Assemblies.

See Bracket Connection detail.

Corner Assembly

Keep extrusions & brackets

assembled for shipment.

DO NOT DISASSEMBLE.

1) Attach horizontals [3,4,5,6]

between verticals [1,2] as shown.

2) Connect bottom bracket [7] to

horizontal [3] using bolts.

3) Connect top bracket [8] to

horizontal [6] using bolts.

Corner Assembly

bolts

TOP VIEW

TSP2

GS310

Z140

Bracket

Qty. 2

1) Connect light strips

together & attach

transformers.

2) Run power cords out

hole in back of light

panel to power source.

Maximum 8 light strips

per transformer.

Light Panel Connection

To Transformer

Light Strip Connector

Cord

Connect Light Strips

together as shown.

Light to Light

Attachment

Light to Transformer

Attachment

Transformer

144W / 6 Amp / 24V

Transformers

Bump-Out Assembly

Step 2 of 8

Order #XXXXX

Locked layer contains

placeholder marks.

Assemble frame flat on ground.

Steps:

Refer to the CEI110 Frame Assembly general information page.

1) Assemble horizontals [11-12] & [13-14] together using

straight connectors.

2) Attach verticals [9,10] between horizontal assemblies using

corner connectors.

3) Connect vertical [15] between horizontal assemblies.

4) Attach Base Plate [17] to bottom-right corner of assembled

frame. See Corner Base Plate Attachment detail.

Item

Qty.

Description

96”h CEI110 Vertical Extrusion

32.5”w CEI110 Horizontal Extrusion

92.353”h Z45 Vertical Extrusion

Corner Base Plate

FRONT VIEW

bolt

wing

nut

bolt

key hole

Corner Base Plate Attachment

*Place key hole over bolt

on vertical extrusion and

slide down; secure with

bolts & wing nuts.

When assembled

Lightbox Assembly

Step 3 of 8

Order #XXXXX

Locked layer contains

placeholder marks.

FRONT ELEVATION VIEW

Power

Female

Transformer

144W / 6 Amp / 24V

Lights Male

Light to Light Attachment

Maximum of 7 lights per chain / 12 lights per Transformer

Light to Transformer Attachment

Steps:

1) Connect power cords to Supernova lights as shown.

Power

Break

Transformer Transformer

Power

Break

Lightbox Wiring

Step 4 of 8

Order #XXXXX

Locked layer contains

placeholder marks.

FRONT VIEW

Steps:

1) Connect bump-out assembly vertical [2] & lightbox vertical [9]

to Post [A], using Bolt to T-Nut Connection as shown.

Item

Qty.

Description

4.5” x 4.5” x 96”h Corner Post

*Bolt to T-Nut

Connection

T-nutt

bolt

When assembled

Connection to Post

Inhaltsverzeichnis

Andere Classic Exhibits Inneneinrichtung Handbücher

Classic Exhibits

Classic Exhibits visionary DESIGNS LTK-1152 Handbuch

Classic Exhibits

Classic Exhibits gravitee GK-1012 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1702 Bedienungsanleitung

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-1201 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Euro LT Hybrids LTK-1012 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1109 Handbuch

Classic Exhibits

Classic Exhibits SEGUE DESIGNS VK-1960 Supernova Bedienungsanleitung

Classic Exhibits

Classic Exhibits SEGUE DESIGNS VK-1852 Bedienungsanleitung

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1590 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-2005 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYM-408 Handbuch

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-1218 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Perfect 10 Helio Bedienungsanleitung

Classic Exhibits

Classic Exhibits Euro LT Hybrids VK-1049 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-1030 Handbuch

Classic Exhibits

Classic Exhibits gravitee GK-2008 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS VK-1131 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1722 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1181 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Curved Counter Handbuch

Classic Exhibits

Classic Exhibits LT-116 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Visionary Designs MOD-1243 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SYK-1029 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYM-412 Handbuch

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung