Classic Exhibits VISIONARY DESIGNS VK-2959 Handbuch

www.classicexhibits.com

Step 1

Page 1 of 8

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - VK-2959 - General Layout

Perspective View

10’

Plan View 20’

www.classicexhibits.com

Step 2

Page 2 of 8

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - General Information

The Tool Typical Connection

Horizontal Inline Connection (remove only one setscrew)

Base Plate Connection Vertical Connection

(remove only two setscrews)

Most Visionary Designs exhibits can be

assembled with the supplied Hex Key Tool.

Occasionally, a flat head screwdriver may

be required.

Most horizontal extrusion connections have a patented expandable lock. This lock inserts into

the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock

and creates a strong positive connection.

Remove only (1) setscrew when disassembling. Replace setscrew in

extrusion after assembling it. Before packing, replace setscrew in

extrusion to avoid losing it.

Attach base plate to round or square

vertical extrusion using the bolt provided.

Be careful not to strip the threads.

When vertical extrusions are packed in

portable cases rather than crates or

tubs, they must broken down into

smaller sections which then require

assembly.

Remove only (2) setscrews when

disassembling. Replace setscrews in

extrusion after assembling it. Before

packing, replace setscrews in extrusion

to avoid losing them.

Using Your Setup Instructions

The Visionary Designs Setup Instructions are created specifically for your

configuration. They are laid out sequentially, including an exploded view of

the entire display, and then a logical series of detailed steps to assemble the

main structure and components. We encourage you to study the instructions

before attempting to assemble your exhibit.

Each page reminds you to tighten the setscrews after disassembling your

exhibit to prevent loss of the locks and setscrews (see below in RED).

This is VERY IMPORTANT.

Cleaning and Packing Your Display

1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only

non-abrasive cleaners.

2) When cleaning laminate inserts or countertops, use mild cleansers and a

soft material such as cotton.

3) Keep all display components away from extreme heat and long exposure

to sunlight to avoid warping and fading.

4) Retain all packing material. It will make re-packing much easier and will

reduce the likelihood of shipping damage.

Typical Connection (cont’d)

Numbered Label

Each extrusion contains a numbered label which

corresponds with setup instructions.

The label is located within a groove of the extrusion

(when possible). With Visionary Designs the labels

contain Black numbers unless otherwise specified.

Detail C EliateDDliateDDetail B

Detail A

Setscrews

www.classicexhibits.com

Step 1

Page 1 of 8

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX -

Transformer

Power

When assembled

Item

1-2

3-4

5-6

7-8

Qty.

1ea.

Description

84”h TSP50 Vertical Extrusion

22”w TSP50 Horizontal Extrusion

83.75”h TSP50 Vertical Extrusion

60”w TSP50 Horizontal Extrusion

Steps:

1) Assemble TSP50 frames together as shown.

Refer to TSP50 w/ A1 L Bracket Attachment detail.

TSP50 Extrusion Profile

Back

Front

Lights

Supernova Lights

**** See attached SEG graphic

installation for graphic attachment

Transformer

Power

**Slide A1 L Bracket into TSP50

extrusion and secure with set screws.

TSP50 w/ A1 L Bracket Attachment

Tighten set

screw to secure

Tighten set

screw to secure

Backwall Assembly - TSP Frames A & B

www.classicexhibits.com

Step 2

Page 2 of 8

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - Backwall Assembly - TSP Frames C & D

When assembled

Item

1-2

3-4

5-6

7-8

Qty.

1ea.

Description

83.75”h TSP50 Vertical Extrusion

34”w TSP50 Horizontal Extrusion

83.75”h TSP50 Vertical Extrusion

84”w TSP50 Horizontal Extrusion

Steps:

1) Assemble TSP50 frames together as shown.

Refer to TSP50 w/ A1 L Bracket Attachment detail.

TSP50 Extrusion Profile

Back

Front

Lights

Transformer

Power

Supernova Lights

**** See attached SEG graphic

installation for graphic attachment

Transformer

Power

**Slide A1 L Bracket into TSP50

extrusion and secure with set screws.

TSP50 w/ A1 L Bracket Attachment

Tighten set

screw to secure

Tighten set

screw to secure

www.classicexhibits.com

Step 3

Page 3 of 8

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - Backwall Sections Assembly

Steps:

1) Attach base plates [11a] to verticals [11] and [12] with bolt as shown.

2) Attach assembled TSP frames [A,B,C,D] between verticals.

Refer to custom cam lock detail.

Item

11a

Qty.

Description

84”h Vertical Extrusion

83.75”h Vertical Extrusion

Oval Base Plate

83.75”h Vertical Extrusion

Top View

Cam Lock

Tighten screw to

clamp cam lock

into groove of

vertical extrusion.

Custom Cam Lock

*** * ***

* *

www.classicexhibits.com

Step 4

Page 4 of 8

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - Backwall Counter Assembly

Item

15/15A

Qty.

2/2

Description

38”h Vertical Extrusion

Curved Horizontal Extrusion

8”w Horizontal Extrusion

Steps:

1) Attach lower horizontals [14,15] between verticals [12,13] and backwall as shown.

2) Attach upper horizontals [14,15A] between verticals [12,13] and backwall as shown.

3) Attach door to vertical [13]. Refer to Door Attachment detail.

4) Attach shelf supports with velcro to inside of assembled base.

5) Place counter atop assembled base as shown.

Shelf

Shelf Supports

(Attach with velcro to inside of assembled base)

Counter

15A

Door

HingeHinge

Door

Hinge

Door Attachment

Slide pin into

hinge attached

to vertical.

Slide door

hinge atop pin.

Infill

HingeHinge

www.classicexhibits.com

Step 5

Page 5 of 8

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - Attachments

ABC

16b

16a

17a

18a

17b

18b

Connect 3 piece Canopy

together by using bolts and

wing nuts provided.

Bolts

Connecting

Canopy Pieces

Together

Example of Canopy Connection

Steps:

1) Connect canopy pieces together using

bolts & wing nuts. Refer to

Example of

Canopy Connection

detail.

2) Assemble arched header pieces together.

3) Attach assembled header to assembled canopy.

Refer to Header Attachment detail.

4) Attach assembled canopy & header atop

assembled backwall.

5) Attach wings using A10 clamps. Refer to

Example of A10 Clamp Attachment detail.

Item

16a/16b

17a/17b

18a/18b

Item

16a/16b

17a/17b

18a/18b

Qty.

1/1

Description

5.862” Vertical Extrusion

40.319” Curved Extru.

39” Horizontal Extrusion

Attaching Graphics

Attach Header Graphic to Back of

assembled header frame.

Bolt

Wing Nut

Header Attachment

16b

16a

17a

18a

17b

18b

When desired location

is found, tighten

set screw to secure.

Tighten knob to

secure shelf in place.

Slide connector on back

of A10 clamp into groove

of extrusion.

A10 Clamp Example

www.classicexhibits.com

Step 6

Page 6 of 8

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - Attachments Cont’d

Attach connector piece to

backside of Lit. Rack as

shown; connect assembly

to vertical extrusion.

Literature Rack Attachment

Tighten Lock

to Secure

Steps:

1) Attach graphic using standoff barrels and caps.

See Graphic Attachment detail.

2) Attach literature rack to backwall as shown.

See Literature Rack Attachment detail.

3) Attach iPad clamshell atop counter as shown.

See iPad Attachment detail.

4) Attach Monitor Mount.

See Monitor Mount Attachment detail.

Graphic

Bolt

Monitor Mount Attachment

Attach monitor mount to horizontal

extrusion using bolts and wing nuts.

Wing

Nut

Graphic

Cap

Standoff

Barrel

Slide connector on back of standoff

barrels into groove of extrusion

and twist to secure in place. Secure graphic

to standoffs using screw caps.

Graphic Attachment

Swivel

Mounting

Plate

iPad Mount Attachment

Hex

Nuts

Swivel

Mounting Plate

Bolt iPad clamshell to

mounting plate with hex nuts.

Attach connector to backside

of iPad Clamshell; connect

assembly to vertical extrusion

Tighten Lock

to Secure

Clam Shell rotates between

portrait and landscape

viewing modes.

Wire Access

iPad

Lock Lock

Graphic

www.classicexhibits.com

Step 7

Page 7 of 8

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - MOD-1267 Pedestal Assembly

Item

21A

22A

23/23A

24/24A

25/25A

Qty.

1/1

Description

38”h Vertical Extrusion w/ Door Hinges

38”h Vertical Extrusion w/ Door Stop

38”h Vertical Extrusion

34.417”h Vertical Extrusion

38”h Vertical Extrusion

34.417”h Vertical Extrusion

22.0197”w Horizontal Extrusion

12.5”w Horizontal Extrusion

26.639”w Curved Horizontal Extrusion

Steps

1) Attach lower horizontal extrusions [23,24,25] between

vertical extrusions [19,20,21,22] as shown.

2) Hang assembled door on hinges on vertical [19] as shown. Refer to detail.

3) Place side and front inserts between verticals as shown.

4) Attach upper horizontal extrusions [23A,24A,25A] between

vertical extrusions [19,20,21,22] and on top of infills as shown.

5) Attach shelf supports to inside of pedestal; set internal

shelf on top of supports.

6) Place counter top on assembled pedestal.

Door

Hinge

Door Attachment

Slide pin into

hinge attached

to vertical.

Slide door

hinge atop pin.

Door

Insert

22A 21

21A

23A

25A

24A

Counter Top

Internal Shelf

Extrusion

w/Door

Hinges

Shelf

Supports

www.classicexhibits.com

Step 8

Page 8 of 8

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - MOD-1267 Pedestal Assembly

Item

21A

22A

23/23A

24/24A

25/25A

Qty.

1/1

Description

38”h Vertical Extrusion w/ Door Hinges

38”h Vertical Extrusion w/ Door Stop

38”h Vertical Extrusion

34.417”h Vertical Extrusion

38”h Vertical Extrusion

34.417”h Vertical Extrusion

22.0197”w Horizontal Extrusion

12.5”w Horizontal Extrusion

26.639”w Curved Horizontal Extrusion

Door

Hinge

Door Attachment

Slide pin into

hinge attached

to vertical.

Slide door

hinge atop pin.

Door

Insert

22A 21

21A

23A

25A

24A

Counter Top

Internal Shelf

Extrusion

w/Door

Hinges

Shelf

Supports

Steps

1) Attach lower horizontal extrusions [23,24,25] between

vertical extrusions [19,20,21,22] as shown.

2) Hang assembled door on hinges on vertical [19] as shown. Refer to detail.

3) Place side and front inserts between verticals as shown.

4) Attach upper horizontal extrusions [23A,24A,25A] between

vertical extrusions [19,20,21,22] and on top of infills as shown.

5) Attach shelf supports to inside of pedestal; set internal

shelf on top of supports.

6) Place counter top on assembled pedestal.

Andere Classic Exhibits Inneneinrichtung Handbücher

Classic Exhibits

Classic Exhibits visionary DESIGNS VK-1950 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Euro LT Hybrids LTK-1012 Handbuch

Classic Exhibits

Classic Exhibits Perfect 10 Bella Bedienungsanleitung

Classic Exhibits

Classic Exhibits SYMPHONY SYK-1022 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1180 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary designs VK-1359 Handbuch

Classic Exhibits

Classic Exhibits Euro LT Hybrids MOD-1121 Handbuch

Classic Exhibits

Classic Exhibits Euro LT Hybrids LTK-1011 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SEGUE DESIGNS VK-1852 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYK-2009 Handbuch

Classic Exhibits

Classic Exhibits eco systems ECO-2056 Bedienungsanleitung

Classic Exhibits

Classic Exhibits LT-116 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-1218 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYK-1005 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1549 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS VK-1131 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1235 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYM-408 Handbuch

Classic Exhibits

Classic Exhibits visionary design MOD-1524 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Magellan Designs VK-1063 Bedienungsanleitung

Classic Exhibits

Classic Exhibits gravitee GK-1008 Handbuch

Classic Exhibits

Classic Exhibits Visionary Designs MOD-1243 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-1222 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-1201 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung