Classic Exhibits Symphony SYK-2005 Handbuch

Order #XXXXX

Locked layer contains

placeholder marks.

Plan View

10’

20’

Perspective View

SYK-2005 - 10’ x 20’ Portable Display

If you would like to tell us about your experience with your setup instructions please email us at [email protected]

SETUP INSTRUCTIONS

REV 7/2022

Order #XXXXX

Locked layer contains

placeholder marks.

= 1 sq ft

Plan View

Order #XXXXX

General Setup Instructions

- Read entire setup instruction manual prior to

unpacking parts and pieces.

- The setup instructions are created specifically

for this configuration.

- Setup instructions are laid out sequentially in

steps, including exploded views with detailed

explanation for assembly.

Cleaning & Packing

- For Cleaning Metal, Plex, & Laminate Parts:

Use a MILD NON-ABRASIVE cleanser and

soft cloth/paper towel to clean all surfaces.

- Keep exhibit components away from heat

and prolonged sun exposure.

Heat and UV exposure will warp and

fade components.

- Retain all provided Packing Materials.

All provided packing materials are for

ease of repacking & component protection.

Disassembly

- For loss prevention, keep all

knobs & connectors attached to

extrusions during disassembly.

Part Identification - Numbering

Engaged Lock

DO NOT USE POWER TOOLS

ALL CONNECTIONS MUST

BE TIGHTLY SECURED

WARNING

General Information

Order #XXXXX

TSP49 Profile

All knobs must be tightened securely to ensure a proper connection.

Adjust connectors if necessary to

prevent gaps in connection.

Upper Horizontal Extrusion

Lower Horizontal Extrusion

Corner

Connector Corner

Connector

Corner

Connector

Corner

Connector

COMPLETED ASSEMBLY

Slide verticals over

lower connectors.

Then slide upper

connectors into

groove of verticals.

Tighten all knobs.

Corner Connection

3) Tighten all knobs to secure connection.

Disassembly

1) Loosen knobs on vertical extrusions.

2) Slide the vertical extrusions off of

corner connectors on lower and upper

horizontal extrusions.

1) Loosen knobs, then slide vertical extrusions onto

corner connectors of lower horizontal extrusion.

2) Slide corner connectors of upper horizontal

extrusion into grooves of vertical extrusions.

Disassembly

1) Loosen all knobs.

2) Slide connectors off of one extrusion.

3) Tighten knobs to prevent loss during

packing & shipping.

Keep straight connectors in groove of

extrusion. Do not remove connectors

during disassembly.

Straight Connection

3) Tighten all knobs to secure connection.

When assembling frame, first attach all straight

connectors, then attach corner connectors.

1) Place extrusions end-to-end.

Slide connector across seam of extrusions.

Tighten all knobs.

All knobs must be tightened securely to ensure a proper connection.

Straight Connector

2) Loosen all knobs, then slide straight

connector across the seam of extrusions.

Tool-less Frame Assembly

Case 1 of 2

Order #XXXXX

Locked layer contains

placeholder marks.

Top View of Each Level

Level 1

(Bottom level)

Level 2 Level 3 Level 4 Level 5

Lights

Setup Hardware

Counter

Top

Counter

Legs

Graphics

8910 6

11 12

2,4

1 3

5,7

Case Packing

Case 2 of 2

Order #XXXXX

Locked layer contains

placeholder marks.

Top View of Each Level

Graphics

Lights

Graphics

Level 1

(Bottom level)

Level 2 Level 3 Level 4 Level 5 Level 6

1 3

5,6

2 4

7,8

1 3

5,6

2 4

7,8

Case Packing

Step 1 of 6

Order #XXXXX

Locked layer contains

placeholder marks.

When assembled

Connection Lock

w/ Knob

BACK VIEW

Knobs face back of assembly.

Tool-less Spline Connector

1. Place extrusions end-to-end.

2. Slide tool-less connectors

across seam of extrusions.

3. Tighten all knobs to secure connection.

Tool-less Corner Connector

1. Slide extrusion onto

Corner Connector.

2. Tighten all knobs to

secure connection.

Keep corner connectors attached to horizontal extrusions.

Assemble frame flat on ground. *

FRONT VIEW

Item

Qty.

Description

45”h TSP49 Vertical Extrusion

31.305”h TSP49 Vertical Extrusion

45”h TSP49 Vertical Extrusion

31.305”h TSP49 Vertical Extrusion

36.467”w TSP49 Horizontal Extrusion

38.019”w TSP49 curved Horizontal Extrusion

45.209”h Z45 Vertical Extrusion

41.209”h Z45 Vertical Extrusion

6” x 22” Base Plate w/ flange (left)

6” x 22” Base Plate w/ flange (right)

Steps:

Refer to the Tool-less Frame Assembly general information page.

1) Assemble vertical extrusions [1-2], [3-4], [11-12] & horizontals [5-6-7], [8-9-10]

together, using Tool-less Spline connectors labeled [X] & [Y].

2) Connect vertical assemblies [1/2], [3/4] between horizontal

assemblies [5/6/7], [8/9/10], using Tool-less Corner Connectors labeled [A] & [B].

3) Install Base Plates [13] & [14] to bottom corners of frame assembly

as shown. See Base Plate Attachment detail.

4) Lift frame to upright position, then connect vertical assembly [11/12] between

horizontal assemblies [5/6/7], [8/9/10] using Connection Lock w/ Knob.

Base Plate Attachment

bolt

knob

Front

key hole

1) Place key hole over bolt

on panel & slide down.

2) Twist knob to secure

connection.

threaded

hole

Base Plate

TOP VIEW

Left Base Plate

TOP VIEW

Right Base Plate

Curved

connector

Arch corner

connector

Arch corner

connector

Curved

connector

Middle Backwall Frame Assembly

Step 2 of 6

Order #XXXXX

Locked layer contains

placeholder marks.

Item

Qty.

Description

45”h TSP49 Vertical Extrusion

27.35”w TSP49 Horizontal Extrusion

6” x 22” End Base Plate w/ foot

When assembled

Tool-less Spline Connector

1. Place extrusions end-to-end.

2. Slide tool-less connectors

across seam of extrusions.

3. Tighten all knobs to secure connection.

Tool-less Corner Connector

1. Slide extrusion onto

Corner Connector.

2. Tighten all knobs to

secure connection.

Keep corner connectors attached to horizontal extrusions.

Assemble frame flat on ground.

Steps:

Refer to the Tool-less Frame Assembly general information page.

1) Assemble vertical extrusions [1-2], [3-4] & horizontal extrusions [5-6], [7-8]

together, using Tool-less Spline connectors labeled [X].

2) Connect vertical assemblies [1/2], [3/4] between horizontal

assemblies [5/6], [7/8], using Tool-less Corner Connectors labeled [A].

3) Install Base Plate [9] to bottom corners of frame assembly

as shown. See Base Plate Attachment detail.

1) Place key hole over bolt on panel

& slide down.

2) Twist knob to secure connection.

Base Plate Attachment

bolt

knob

Base Plate

threaded

hole

key hole

FRONT VIEW

Left Backwall Frame Assembly

Step 3 of 6

Order #XXXXX

Locked layer contains

placeholder marks.

Item

Qty.

Description

45”h TSP49 Vertical Extrusion

27.35”w TSP49 Horizontal Extrusion

6” x 22” End Base Plate w/ foot

When assembled

Tool-less Spline Connector

1. Place extrusions end-to-end.

2. Slide tool-less connectors

across seam of extrusions.

3. Tighten all knobs to secure connection.

Tool-less Corner Connector

1. Slide extrusion onto

Corner Connector.

2. Tighten all knobs to

secure connection.

Keep corner connectors attached to horizontal extrusions.

Assemble frame flat on ground.

FRONT VIEW *

Steps:

Refer to the Tool-less Frame Assembly general information page.

1) Assemble vertical extrusions [1-2], [3-4] & horizontal extrusions [5-6], [7-8]

together, using Tool-less Spline connectors labeled [X].

2) Connect vertical assemblies [1/2], [3/4] between horizontal

assemblies [5/6], [7/8], using Tool-less Corner Connectors labeled [A].

3) Install Base Plate [9] to bottom corners of frame assembly

as shown. See Base Plate Attachment detail.

1) Place key hole over bolt on panel

& slide down.

2) Twist knob to secure connection.

Base Plate Attachment

bolt

knob

Base Plate

threaded

hole

key hole

Right Backwall Frame Assembly

Step 4 of 6

Order #XXXXX

Locked layer contains

placeholder marks.

Left Frame

Right Frame

Steps:

1) Connect vertical of Left Frame Assembly to

Base Plate of Middle Frame Assembly.

See Base Plate Attachment detail.

2) Attach vertical of Right Frame Assembly to

Base Plate of Middle Frame Assembly.

See Base Plate Connection detail.

When assembled

FRONT VIEW

TOP VIEW

Left Base Plate

TOP VIEW

Right Base Plate

Base Plate Attachment

Place key hole over bolt on panel & slide down.

Twist knob to secure connection.

Front

Base Plate

key hole

bolt

Backwall Frames Connection

Inhaltsverzeichnis

Andere Classic Exhibits Inneneinrichtung Handbücher

Classic Exhibits

Classic Exhibits visionary MOD-1294 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SYMPHONY SYM-408B Handbuch

Classic Exhibits

Classic Exhibits Magellan Designs VK-1091 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS VK-4022 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYM-408 Handbuch

Classic Exhibits

Classic Exhibits visionary design MOD-1524 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYK-2009 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-1030 Handbuch

Classic Exhibits

Classic Exhibits GRAVITEE GOD-1559 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1109 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-2037 Handbuch

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-1218 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Euro LT Hybrids LTK-1114 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary Magellan Miracle VK-2094 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Perfect 10 Bella Bedienungsanleitung

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1711 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYM-412 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-1214 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary VK-2098 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYK-1019 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1519 Handbuch

Classic Exhibits

Classic Exhibits RE-2015 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Perfect 10 Helio Bedienungsanleitung

Classic Exhibits

Classic Exhibits LT-116 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung