Classic Exhibits VISIONARY DESIGNS VK-1214 Bedienungsanleitung

www.classicexhibits.com

Step 1

Page 1 of 4

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #xxxxx - Sacagawea - VK-1214 - General Layout

10’

Plan View

www.classicexhibits.com

Step 2

Page 2 of 4

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #xxxxx - Sacagawea - General Information

The Tool Typical Connection

Horizontal Inline Connection (remove only one setscrew)

Base Plate Connection Vertical Connection

(remove only two setscrews)

Most Visionary Designs exhibits can be

assembled with the supplied Hex Key Tool.

Occasionally, a flat head screwdriver may

be required.

Most horizontal extrusion connections have a patented expandable lock. This lock inserts into

the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock

and creates a strong positive connection.

Remove only (1) setscrew when disassembling. Replace setscrew in

extrusion after assembling it. Before packing, replace setscrew in

extrusion to avoid losing it.

Attach base plate to round or square

vertical extrusion using the bolt provided.

Be careful not to strip the threads.

When vertical extrusions are packed in

portable cases rather than crates or

tubs, they must broken down into

smaller sections which then require

assembly.

Remove only (2) setscrews when

disassembling. Replace setscrews in

extrusion after assembling it. Before

packing, replace setscrews in extrusion

to avoid losing them.

Using Your Setup Instructions

The Visionary Designs Setup Instructions are created specifically for your

configuration. They are laid out sequentially, including an exploded view of

the entire display, and then a logical series of detailed steps to assemble the

main structure and components. We encourage you to study the instructions

before attempting to assemble your exhibit.

Each page reminds you to tighten the setscrews after disassembling your

exhibit to prevent loss of the locks and setscrews (see below in RED).

This is VERY IMPORTANT.

Cleaning and Packing Your Display

1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only

non-abrasive cleaners.

2) When cleaning laminate inserts or countertops, use mild cleansers and a

soft material such as cotton.

3) Keep all display components away from extreme heat and long exposure

to sunlight to avoid warping and fading.

4) Retain all packing material. It will make re-packing much easier and will

reduce the likelihood of shipping damage.

Typical Connection (cont’d)

Numbered Label

Each extrusion contains a numbered label which

corresponds with setup instructions.

The label is located within a groove of the extrusion

(when possible). With Visionary Designs the labels

contain Black numbers unless otherwise specified.

Detail C EliateDDliateDDetail B

Detail A

Setscrews

www.classicexhibits.com

Step 1

Page 1 of 4

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #xxxxx - Sacagawea - Backwall Assembly

Set upper horizontal bars

[51/5b] to be flush with

top of vertical extrusions.

Horizontal Placement

Connection

Bar

Slide Connection Bar

between Extrusions

and tighten Knobs

to secure.

Connection

Bar

Graphic Attachment

Apply graphic to back

of assembled backwall.

Connection

Bar

Connection

Bar b

A10 clamps attached to vertical extrusions fo Wing Attachment

Item

4a/4b

5a/5b

Description

Base Plate

42”h Lower Square Vertical Extrusion

42”h Upper Square Vertical Extrusion

42”h Lower Square Vertical Extrusion w/ A10 Clamps Attached

42”h Upper Square Vertical Extrusion w/ A10 Clamps Attached

45”w Horizontal Extrusion

Qty.

1/1

Steps:

1) Attach vertical extrusions [2] to base plates [1].

2) Attach upper vertical extrusions [3a and 3] to lower extrusions [2a and 2]

using connection bar [a].

3) Connect horizontal extrusions [4a to 4b and 5a to 5b] together using connection bar [b].

4) Attach horizontal assemblies [4a/4b and 5a/5b] between vertical assemblies as shown.

5) Apply graphic to back of assembled backwall.

6) Attach light to top of assembled backwall.

Turn Knob Clockwise

to Tighten Lock

STAR indicates location of

knobs on BACKSIDE of unit.

**Do not over tighten Knobs.**

Knob

Light Connection

Attach Lights to

Backwall where

desired and tighten

in place.

GREEN STAR indicates

location of connection

lock with knob.

www.classicexhibits.com

Step 2

Page 2 of 4

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #xxxxx - Sacagawea -

*Note: Curved extrusion

[10] and horizontal [11]

must stay assembled

when shipping.

Item

11a

Description

30.2” Curved Extrusion

12.184”w Horizontal Extrusion

Flange Plate

Qty.

Steps:

1) Connect horizontal extrusion [11] to curved extrusion [10].

2) attach assembled counter support [10/11] to vertical where indicated.

3) Attach flange plate [11a] to top of curved extrusion [10] as shown.

4) Attach counter atop support, see counter top attachment detail.

5) Attach wing panels to A10 clips.

6) Attach monitor mount to backwall where indicated.

Counter Top Attachment

Insert screws located on underside

of counter into holes on flange plate

and secure with wing nuts.

Wing Nut

Screw

11a

Monitor Mount Attachment

Connectors

Attach monitor mount back plate

to connectors using screws provided.

Slide A10 Clamp

into groove

of square extrusion.

When desired location

is found, tighten

set screw to secure.

Set-

Screw

A10

Tighten black plastic

set screw to secure

Wing in place.

Black Plastic

Set-screw

Wing Attachment

*Note: A10 clamps must

stay attached with verticals

Counter and Wing Attachment

www.classicexhibits.com

Step 3

Page 3 of 4

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #xxxxx - Sacagawea - Canopy Assembly

Connections are made by holding the button

down and sliding the red tube into opposing

tube until the connection is made. To disassemble

push button and pull or twist extrusions apart.

Push-Button

Numbered Label

Using Your Setup Instructions

The Aero Overhead Sign Setup Instructions are created speciﬁcally for your conﬁguration. They include an

exploded view of the frame which is sequentially numbered. We encourage you to study the instructions

before attempting to assemble your exhibit.

Connections are kept very simple: no tools. Everything assembles with push-button

connectors and pre-connected horizontal sections.

Cleaning and Packing Your Display

1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.

2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood

of shipping damage.

Steps:

1) Connect canopy pieces together as shown.

2) Apply pillow case graphic to assembled canopy

Push-Button

Push button then rotate

for packing purposes

www.classicexhibits.com

Step 4

Page 4 of 4

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #xxxxx - Sacagawea - MOD-1243 - Pedestal Assembly

Part Number

13/13a

Qty

2/2

Description

38”h Vertical Extrusion

12”w Horizontal Extrusion

25”w Horizontal Extrusion

Steps

Attach horizontal extrusions [13 and 13a] between vertical

extrusions [12], placing inserts between horizontals.

2) Attach curved horizontal extrusions [14] between

vertical extrusions [12], placing insert between

curved horizontals.

Sintra Insert

Top View

Shelf

Steps (Cont’d):

3) Place shelf atop lip of extrusions.

4) Set counter top atop assembled base.

Counter

Extrusions 13a

have a lip for the

floor to rest

upon.

Lip for Shelf

Placement

Lip

Extrusion Details:

13a

12 12

13a

12 12

*Note: Pedestal sides

must stay assembled

when shipping

www.classicexhibits.com

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #xxxxx - Case Packing Instruction - Case 1 of 2

Canopy Pieces

(1) Backwall Components

Extrusions #3&3a

Extrusions #2&2a

Horizontal extrusions #4a&4b abd 5a&5b

Connection Bars A

Connection Bars B

Counter

Top

Base Plates

Backwall Counter

Support

Level 1 Level 2 Level 3 Level 4

Wing Panels

Level 5

Setup Hardware

and Lights

Graphics

www.classicexhibits.com

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #xxxxx - Case Packing Instruction - Case 2 of 2

(2) Pedestal Components

Level 1 Level 2 Level 3 Level 4

Counter Top

Curved Extrusions # 14

Assembled

Pedestal

Side

Assembled

Pedestal

Side

Front Insert

Internal Shelf

Andere Classic Exhibits Inneneinrichtung Handbücher

Classic Exhibits

Classic Exhibits Symphony SYK-1005 Handbuch

Classic Exhibits

Classic Exhibits visionary designs VK-2084 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYM-408 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1722 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS VK-1341 Handbuch

Classic Exhibits

Classic Exhibits gravitee GOD-1557 Handbuch

Classic Exhibits

Classic Exhibits SYMPHONY SYK-2021 Handbuch

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-2113 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SEGUE DESIGNS VK-1852 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-2101 Bedienungsanleitung

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1711 Handbuch

Classic Exhibits

Classic Exhibits Magellan Designs VK-1063 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Euro LT Hybrids MOD-1121 Handbuch

Classic Exhibits

Classic Exhibits euro lt HYBRIDS Mod-1122 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS 38907 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-1201 Bedienungsanleitung

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-3006 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1181 Bedienungsanleitung

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1556C Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYK-2037 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1549 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1235 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYK-1030 Handbuch

Classic Exhibits

Classic Exhibits Perfect 10 Helio Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung