Classic Exhibits Perfect 10 Helio Bedienungsanleitung

www.classicexhibits.com

866.652.2100

WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING

Order #xxxxx - p10 -

Page 1 of 6

Step 1

Helio - General Layout

Plan View

10’

www.classicexhibits.com

866.652.2100

WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING

Order #xxxxx - p10 -

Page 1 of 6

Step 1

Helio - Backwall Assembly

Part Number

Step 1:

NOTE: Can be assembled either face down on floor then lifted

upright or upright as shown in drawings.

A) Connect vertical leg assemblies [1 and 2] together by connecting horizontal extrusions

[4] between assemblies tightening BLACK knobs on backside of extrusion making sure Velcro

faces toward BACK and placing it about one inch up from bottom and tightening.

B) Connect vertical extrusions [3 and 3A] to leg assemblies [1 and 2] using vertical connection

bar as shown.

C) Connect upper horizontal extrusion [4] between verticals [3 and 3A] placing it about one

inch down from top.

NOTE: Make sure the lock is flush with extrusion before tightening. If lock will not fully

engage, gently rock lock and extrusion while turning knob until lock fully opens.

Description

Left Leg Assembly w/ A10 Clamps Attached

Middle Leg Assembly

Upper Curved Vertical w/ A10 Clamps Attached

Upper Curved Vertical

23”w Horizontal

3A 3

Black

Knob

Turn Knob Clockwise

to Tighten Lock

STAR indicates location of

knobs on BACKSIDE of unit.

Vertical

Connection Bar

NOTE:When assembling horizontals they should

be placed approximately one inch from TOP and BOTTOM.

Slide

horizontal into groove

Assure

that a good

connection is made

and tighten to secure.

Slide Connection Bar into lower

leg assembly. Slide upper vertical

over bar and secure both.

Rear View of Display

Step 1

Step stool may be required

for assembly.

www.classicexhibits.com

866.652.2100

WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING

Order #xxxxx - p10 -

Page 2 of 6

Step 2

Helio - Backwall Assembly

Step 2:

NOTE: Can be assembled either face down on floor then lifted

upright or upright as shown in drawings.

A) Connect vertical extrusion [6] to leg assembly [5] using vertical connection bar as shown.

B) Connect horizontal extrusions [7 and 8] between vertical assemblies by tightening

BLACK knobs on backside of extrusion making sure Velcro faces toward BACK.

NOTE: Make sure the lock is flush with extrusion before tightening. If lock will not fully

engage, gently rock lock and extrusion while turning knob until lock fully opens.

3A 3

Black

Knob

Turn Knob Clockwise

to Tighten Lock

STAR indicates location of

knobs on BACKSIDE of unit.

Hinge Extrusion

Top Horizontal Hinge faces down.

Bottom Horizontal Hinge faces up.

NOTE:When assembling horizontals they should

be placed approximately one inch from TOP and BOTTOM.

Slide

horizontal into groove

Assure

that a good

connection is made

and tighten to secure.

Slide Connection Bar into lower

leg assembly. Slide upper vertical

over bar and secure both.

Rear View of Display

Step 2

Part Number

Description

Right Leg Assembly w/ A10 Clamps Attached

Upper Curved Vertical

69”w Horizontal w/ Hinge Facing UP

69”w Horizontal w/ Hinge Facing DOWN

www.classicexhibits.com

866.652.2100

WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING

Order #xxxxx - p10 -

Page 3 of 6

Step 3

Helio - Wing and Blade Assembly

Slide A10 Clamp into groove

of square extrusion.

When desired location is

found, tighten set screw

to secure.

Set-

Screw

A10

Tighten black plastic set screw

to secure Wing in place.

Black Plastic

Set-screw

Decorative Blade Attachment

(if accidently removed)

Attach decorative wing and

blades to A10’s attached to

Backwall as shown. 9

Hex Key Tool Flathead

Screwdriver

(if necessary)

www.classicexhibits.com

866.652.2100

WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING

Order #xxxxx - p10 -

Page 4 of 6

Step 4

Helio - Header, Cubby and Shelf Placement

Light Connection

Attach Lights to

Backwall where

desired and tighten

in place.

Shelf attaches to section

5 by setting atop pins

located on right side

and securing into place

with thumbscrew on left.

Cubby Attachment

Slide onto back pin first.

When attaching counter you will need to first

slide shelf onto back pin then set down on front

pin.

Accessary Attachment

Attach Header support to Backwall

then attach header to support by Velcroing it.

Header

Pins

Thumbscrew

Shelf attaches to back of

sections 1 and 2 by setting

atop pins located on back left

side.

www.classicexhibits.com

866.652.2100

WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING

Order #xxxxx - p10 - Case Packing - Case 1 of 2

Level 1

Level 2

Level 3

Level 4

Level 5

Top View of each Level

Case #1 - Backwall Components

Leg Assembly

Wing Attachment

Blade Wing

Header

Vertical Connection Bar

Horizontal Extrusions #6

Horizontal Extrusion 5

A10’s

Attached

Cutout

for A10 Clamp

A10’s

Attached

Header Support

Header Supports

Header

www.classicexhibits.com

866.652.2100

WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING

Order #xxxxx - p10 -

Level 1

Level 2

Top View of each Level

Case #2 - Backwall Components

Backside

Shelf

Cubby

Wings

Case Packing - Case 2 of 2

Dieses Handbuch passt für folgende Modelle

Andere Classic Exhibits Inneneinrichtung Handbücher

Classic Exhibits

Classic Exhibits visionary MOD-1294 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SYMPHONY SYM-408B Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS VK-1131 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-1019 Handbuch

Classic Exhibits

Classic Exhibits gravitee GK-1008 Handbuch

Classic Exhibits

Classic Exhibits RE-2015 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Perfect 10 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SYMPHONY SYK-1022 Handbuch

Classic Exhibits

Classic Exhibits visionary designs MOD-1529 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-3006 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-1046 Handbuch

Classic Exhibits

Classic Exhibits SYMPHONY SYM-406B Handbuch

Classic Exhibits

Classic Exhibits visionary designs VK-2084 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-1226 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-2108 Bedienungsanleitung

Classic Exhibits

Classic Exhibits eco systems ECO-4100 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-1214 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS LTK-1152 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-2009 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYM-412 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1549 Handbuch

Classic Exhibits

Classic Exhibits SYK-1029 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYM-408 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-1030 Handbuch

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung