Clifford Concept 100 Bedienungsanleitung

World-ClassAutoSecurity TM

Standard Features of the ACE 100

✔Lifetime Warranty — For as long as you own the vehicle, Clifford will repair or

replace the control unit and remote controls free of charge (see warranty card for

full details).

✔FACT™—False Alarm Control and Test — One of many patented Clifford

innovations, FACT absolutely, positively ends recurring false alarms.

✔A Pair of 2-Button/3-Channel Remote Controls — Fingertip command from a

typical range of 100 feet.

✔AntiScan™—Blocks the digital code scanners still used by some thieves.

✔Remote Door Lock/Unlock Outputs — No more fumbling with keys in the dark

or bad weather! A press of a button on the remote simultaneously arms ACE 100

and locks your car’s power locks. Another press disarms and unlocks. (Some

vehicles require optional relays.)

✔Built-In Parking Light Flasher — Visually confirms door lock and system status.

✔Remote Controlled Chirp Muting— Silently arm or disarm the system

whenever you wish by pressing both buttons on the remote control.

✔User-Selectable AutoArming™— Automatically arms itself “passively” if you

forget. May qualify you for an insurance discount that could pay for the system

(consult your insurance company).

AutoArming Enable/Disable — You may disable or re-enable AutoArming

with just a few flicks of a switch.

AutoArm & Lock™ — You may set the system to automatically lock the doors

every time the system AutoArms.

✔All Electronic Piezo Sensor— An all-electronic vibration/impact sensor that

delivers the utmost reliability and provides more accurate discrimination between

genuine intrusion attempts and non-threatening conditions (like a large truck

passing by) that cause other sensors to false alarm.

✔Patented AutoTesting™—Automatically tests all system triggers and sensors

every time you remotely arm and warns you if you accidentally arm your ACE

100 system with the hood or trunk open.

Standard Features of the ACE 100 (cont.)

✔High-Output Siren — Loud siren wail for 30 seconds when the alarm detects an

intrusion attempt. The system then automatically resets and rearms.

✔Patented Malfunction AutoBypass™ —In the unlikely event of a trigger or

sensor malfunction, your ACE 100 will automatically bypass the malfunction and

arm all other points to continue relentless protection of your vehicle.

✔Patented Prior Intrusion Attempt Alert — When you return to your vehicle and

remotely disarm your ACE 100, a special chirp and parking light flash sequence

will audibly and visually alert you from a distance if an intrusion attempt was

foiled while you were away.

✔Patented Remote Control Code Learning — Just a few flicks of a switch lets

you match to the system up to 4 different 2-button/3-channel Clifford remote

controls. Just as easily, a lost or stolen remote control can be deleted.

✔Advanced CMOS Microcomputer —Very large scale integration (VLSI)

microprocessor commands and monitors all system functions more than

1,000,000 times per second, yet it draws less power than the vehicle’s clock, so it

won’t deplete your car battery like other alarms.

✔Fault-Proof Starter Interrupt — The system will electronically prevent an

intruder from starting the engine while the system is armed.

✔Hood/Trunk Trigger Input— For full perimeter protection of the engine

compartment and trunk contents (may require optional pin switches).

✔High-Luminescence LED Status Indicator — Adds visual deterrence and

identifies system status.

✔Full-Time Remote Panic — If you feel threatened, you can remotely activate the

siren and flash the parking lights with just a press on your remote control.

✔Valet Mode — Permits vehicle servicing and valet parking without relinquishing

the remote control.

✔Patented SmartPowerUp™ II — When power to the system is disconnected, the

system’s non-volatile memory always remembers the last state (armed, disarmed

or valet mode) and returns to that state when power is restored. So if a thief

disconnects the power and then restores it in an attempt to start the car, the

system will re-arm and instantly sound the siren while immobilizing the vehicle.

Your 2-button/3-channel remote controls

The 2-button/3-channel remote controls are miniature radio transmitters powered by a

12-volt batteries. Range is up to 100 feet (a weak remote control battery will reduce

range). The remote control is the key to your system. You will use it to arm and

disarm the system, lock* and unlock* the doors, activate the panic feature, command

options such as a remote trunk release, power window operation, or other accessory.

TO ARM

THE SYSTEM . . . . . . . Press button I once. You will hear two chirps and the parking

lights will flash twice. The dashboard LED will flash

repeatedly and the car doors will automatically lock.*

TO DISARM

THE SYSTEM . . . . . . . Press button I again. One chirp and one parking light flash

confirm disarming, and the doors will automatically unlock.*

TO SILENTLY

ARM OR DISARM. . . Press both buttons I+II. The system will arm or disarm with

all the indications noted above except the chirp confirmations.

TO ACTIVATE

THE PANIC

FEATURE . . . . . . . . . .

Press button I (channel 1) for 3 seconds. The parking lights

will flash repeatedly and the siren will blare for 30 seconds or

until you press button I again to turn it off.

TO REMOTELY

CONTROL AN OPTION Button II (channel 2) can optionally pop the trunk or activate

another optional accessory.

AutoArming™

If this feature is enabled and you forget to remotely arm, ACE 100 automatically arms

itself 30 seconds after the doors are closed. For your convenience, if you re-open any

door(s) within the 30-second countdown, AutoArming will restart from the beginning

once all doors are closed. ACE 100 has these additional AutoArming features:

AutoArming enable/disable: If you prefer, you may deactivate or reactivate

the AutoArming feature. See User-selectable features on page 6.

AutoArm & Lock: To ensure you can’t accidentally lock your keys inside the

car, the system is factory-set not to lock* the doors upon AutoArming. To

change this setting, see User-selectable features on page 6.

* Some vehicles require optional relays to control the vehicle’s power locks.

Valet mode

Whenever the system is put in valet mode, all of the system’s security features are

switched off. At various times, you will need to turn the system off. For instance,

when having your car serviced, washed or parked by a valet.

NOTE: If you temporarily lose the use of your remote controls, you can disarm

the system by enabling valet mode.

To enable valet mode

1. Turn the ignition switch to its “ON” position or start the engine.

2. Flip the valet switch. The system’s LED will glow continually for on-going

visual confirmation of valet mode.

To exit valet mode

1. Turn the ignition switch to its “ON” position or start the engine.

2. Flip the valet switch. The system’s LED will turn off to confirm that the system

is in its normal operating mode.

How to interpret the chirps and parking light flashes

When you use the remote control, the system responds with chirps and parking light

flashes. These chirp/flash acknowledgments mean:

Piezo Sensor

The Piezo Sensor that detects intrusion-related vibrations and impacts.

AutoTesting™

Each time you remotely arm your ACE 100, it automatically performs an extensive

test of all system triggers and sensors. If the hood or trunk is open when you

remotely arm, the system will immediately alert you of the problem by sounding 4

chirps and 4 parking light flashes instead of the usual 2 and 2 (simply disarm, shut

the hood or trunk and re-arm to reactivate monitoring of that trigger point). If a door

is ajar or if a sensor is malfunctioning, you will receive the usual 2 chirps and 2

flashes, then, 5 seconds later, there will be 4 chirps and 4 flashes. (The door ajar

warning will not work on vehicles that have factory-delayed courtesy lights).

Chirps/flashes Meaning

1Your system is disarmed

2Your system is armed

2 and then 4 Armed but a door is open or the sensor is malfunctioning (see AutoTesting below)

3Disarmed but there was an intrusion attempt (see Prior intrusion attempt alert on page 5)

4Armed but the hood or trunk is ajar (see AutoTesting below)

Automatic malfunction bypass

The system automatically bypasses any faulty point and arms all other triggers and

sensors to provide the utmost protection until you can have the system serviced.

Prior intrusion attempt alert

If you hear three chirps when you remotely disarm, the alarm sounded in your absence.

FACT™— False Alarm Control and Test

With FACT, you’ll never experience repeated false alarms. If the siren goes off, DO

NOT remotely disarm the system; allow it to run for the full 30 seconds. Before

sounding a second time, the system checks for another activated trigger to verify an

intrusion is in progress. If the siren sounds again, you will know for sure that

someone is tampering with your vehicle.

Dual-level tamper warning

You may set the system to issue a rapid five-chirp warning, instead of the full alarm,

whenever the system detects tampering. If there is any further tampering, or if a door,

the hood or the trunk is opened at any time, your system will sound the full alarm.

Fault-Proof starter interrupt

Your ACE 100 will automatically prevent the engine from being started while the

system is armed. Clifford’s Fault-Proof design ensures that you can start the engine

even in the unlikely event of a system malfunction.

High-output siren

Loud siren wail when the system detects an intrusion. Your ACE 100 also has

remote controlled chirp muting that is valuable when parking late at night in a quiet

residential area or any time when you want to arm or disarm silently. To do so,

simply press both buttons I+II on your remote control instead of the usual button I.

SmartPowerUp™ II

If power to the system is ever removed, SmartPowerUp II ensures the system will

automatically restore itself to its previous state when power is restored. So if a thief

disconnects the power and then restores it in an attempt to start the car, the system

will re-arm and instantly sound the siren while immobilizing the vehicle. If your

vehicle is to be serviced by a mechanic, just put the system in valet mode. If the

mechanic needs to interrupt power, your system will automatically return to its valet

mode state when power is restored; there will be no alarm activation and no need to

provide your mechanic with your remote control and instructions on how to use it.

User-selectable features

Your ACE 100 vehicle security system allows you to set many of its features to

your own personal preferences. We have made the programming procedures very

simple: to make a change, you just flick the valet switch a few times. The system

comes from the factory with all of its features pre-programmed as noted in the table

below. To change any of the settings, use the following procedure. To restore the

feature to its factory setting, just repeat the procedure:

1. Select the feature you wish to program from the table below. Note the number of

flicks and chirps.

2. Turn your vehicle’s ignition switch to its “ON” position.

3. Immediately flick the valet switch back and forth, counting the number of chirps you

hear. Stop when you reach the number of chirps associated with the feature you wish

to program.

4. If noted, perform the “Secondary action.”

5. Wait 3 seconds. You will hear 1-5 chirps (as noted in the “Program completion

confirmation” column) and the LED will turn off. Turn the ignition off.

6. Repeat steps 1-5 for any other features you wish to program.

Feature Factory

setting

# of

flicks &

chirps

Secondary

action

Program

completion

confirmation Result

AutoArming ON 4—1 chirp = OFF

2 chirps = ON Change state from

ON to OFF or vice-versa

AutoArm

& Lock OFF 5—1 chirp = OFF

2 chirps = ON Change state from

OFF to ON or vice-versa

Tamper

Warning OFF 11 —1 chirp = OFF

2 chirps = ON Change state from

ON to OFF or vice-versa

FACT ON 12 —1 chirp = OFF

2 chirps = ON Change state from

ON to OFF or vice-versa

Add a new

remote to

channel 1

(arm/disarm) —13 Press remote control button I 1 chirp Button I/channel 1 code

of the new remote control

has been memorized

Add a new

remote to

channel 2

(remote

accessory)

—14 Press remote control button II 2 chirps Button II/channel 2 code

of the new remote control

has been memorized

Add a new

remote to

channel 3

(silent

arm/disarm)

—15 Simultaneously press remote

control buttons I+II 3 chirps Buttons I+II/channel 3 code

of the new remote control

has been memorized

Adding new remote controls

For other drivers in your family, or if you wish to control Clifford systems on your

other cars with the same remote control, you can buy additional Clifford remote

controls from any Clifford Dealer (or call our Customer Service Department at

800-824-3208) and program them into the system yourself. Each ACE 100 will

respond to as many as four remote controls. To add a new remote control to the

system, use the procedures noted in the User-selectable features section on page 6.

How to erase the codes of lost or stolen remote controls

If one of your remote controls is ever lost or stolen, you can erase its digital codes

from the system memory to make sure that the missing remote control can never be

used to disarm your system. Just use the Adding new remote controls procedure

noted above for a total of four times (e.g., if you have one remote control remaining,

program it four times; if you have two remote controls, program each twice).

Example: To change the AutoArming feature from “on” to

“off,” you would do the following:

•Turn the ignition key to the ON position.

•Flick the valet switch back and forth 4 times (you’ll hear a chirp each

time to help you count to the total of 4 chirps).

•Wait 3 seconds. The system will sound one more chirp to confirm

that the AutoArming setting is now off (1 chirp = off, 2 chirps = on).

•Turn the ignition off. That’s all there is to it! To change the

ACE 100 is covered by

one or more of the following Clifford Electronics patents:

4,158,874; 4,233,642; 4,327,444; 4,383,242; 4,430,685; 4,845,464;

4,887,064; 4,890,108; 4,922,224; 4,997,053; 5,081,667; 5,146,215;

5,157,375; 5,467,070; 5,650,774 and other patents pending

Andere Handbücher für Concept 100

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clifford Autoalarmanlage Handbücher

Clifford

Clifford Concept 600 Bedienungsanleitung

Clifford

Clifford 510.4X Bedienungsanleitung

Clifford

Clifford GP500 Bedienungsanleitung

Clifford

Clifford Cyber 5 Bedienungsanleitung

Clifford

Clifford Matrix RS1.1 Bedienungsanleitung

Clifford

Clifford Self-Powered SmartSiren 4 60-589 Bedienungsanleitung

Clifford

Clifford Auto Immobilizer Bedienungsanleitung

Clifford

Clifford 300 Bedienungsanleitung

Clifford

Clifford Polaris II Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Clifford

Clifford concept 50 Bedienungsanleitung

Clifford

Clifford cyber Arrow 3 Bedienungsanleitung

Clifford

Clifford 3706X Bedienungsanleitung

Clifford

Clifford Cyber 1 Bedienungsanleitung

Clifford

Clifford Centurion Bedienungsanleitung

Clifford

Clifford IntelliGuard 8000 Bedienungsanleitung

Clifford

Clifford 4105X Bedienungsanleitung

Clifford

Clifford 4806X Bedienungsanleitung

Clifford

Clifford Model RSX1.2 Bedienungsanleitung

Clifford

Clifford Nova III Bedienungsanleitung

Clifford

Clifford SmartWindows 4 Bedienungsanleitung

Clifford

Clifford Concept 650 Bedienungsanleitung

Clifford

Clifford 3305X Bedienungsanleitung

Clifford

Clifford SuperNova Auto Security SuperNova Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung

SECO-LARM

SECO-LARM 300C Bedienungsanleitung

Python

Python 660XP Bedienungsanleitung

Megalarm

Megalarm MEGA 3600 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2011RS Series III Super Rage Bedienungsanleitung