Clifford XL1000 Bedienungsanleitung

Owner’sManual

World-ClassAutoSecurity TM

Using Your XL1000 Security System

2-Button/3-Channel Remote Control

The 2-button/3-channel remote control is a miniature radio transmitter with a range

of up to 100 feet. Obstructions, interference or a weak battery will reduce the range.

Your 2-button/3-channel remote control is the key to your security system. It is an

ingenious user-friendly device that transmits three distinct and unique digital codes.

Use it to arm or disarm the system, lock or unlock the doors, activate its panic

feature or control options such as the SmartWindows II accessory and a remote

trunk release.

TO ARM

THE SYSTEM. . . . . . Press button I once. You will hear two chirps and the parking

lights will flash twice. The dashboard LED will flash repeat-

edly and the car doors will automatically lock. Any attempt to

break into the vehicle will immediately disable the starter,

sound the siren and flash the parking lights.

TO DISARM

THE SYSTEM. . . . . . Press button I again. One chirp and one flash of the parking

lights will confirm disarming. In addition, the car doors will

automatically unlock and the interior lights will turn on and

stay on for 30 seconds or until you start the engine.

TO ACTIVATE AN

OPTION . . . . . . . . . . .Press button II to activate a remote controlled option, such as a

remote trunk release (be sure to disarm the XL1000 before re-

motely releasing the trunk latch).

TO SILENTLY

ARM OR DISARM

THE SYSTEM. . . . . .

Simultaneously press buttons I+II (or button III of the optional

4-channel remote). The system will arm or disarm with all the

indications noted above except the chirp acknowledgments.

TO ACTIVATE

THE PANIC

FEATURE. . . . . . . . .

Press button I for 3 seconds. The lights will flash repeatedly

and the siren will blare for 30 seconds or until you press but-

ton I again to turn it off.

TO ACTIVATE

A SECOND

OPTION . . . . . . . . . . .

If you have an optional Clifford 4-button/4-channel remote

control, press button IV to activate another remote controlled

option, such as the Clifford IntelliStart™ remote engine/

heater/defroster/air conditioner starter accessory (refer to the

IntelliStart’s operating instructions).

AutoLock/AutoUnlock

For your safety and that of your passengers, the system automatically locks the doors

when you turn on the ignition switch to start the engine and unlocks them once the

ignition is turned off. If you prefer, you may turn off the AutoLock/AutoUnlock

feature. See the User-Selectable Features section on pages 6-7.

AutoArming™

If you forget to remotely arm, the system will arm itself automatically (“passively”)

30 seconds after the vehicle doors are closed. If you re-open any door(s) within the

30-second countdown, AutoArming will restart from the beginning once all doors

are closed. This ensures you’ll never accidentally leave your vehicle unprotected.

AutoArming Enable/Disable:If you prefer, you may deactivate or reactivate

AutoArming. To do, see User-Selectable Features on pages 6-7.

AutoArm & Lock: To ensure you can’t accidentally lock your keys inside the

car, the system is factory-set not to lock the doors upon AutoArming. To

change this setting, see User-Selectable Features on pages 6-7.

NOTE: To prevent AutoArming of the system when fueling the vehicle, either

enable valet mode or leave one of the doors open (the system AutoArms 30

seconds after all doors are closed).

Protected Valet Mode

Whenever the alarm is put in protected valet mode, all of the alarm functions are

bypassed, preventing AutoArming and accidental activation of the alarm. Use the

valet mode whenever your car is either to be serviced by mechanics, handed over

to car wash personnel or driven by valet attendants. It also comes in handy if you

ever lose your remote control or its battery dies. If you have the AutoArming

feature set on, when fueling your car, either put the alarm in valet mode or leave

the driver’s door open (the system will not AutoArm if a door is open). Be sure to

ask your installer to show you where the valet switch is located.

To turn ON the protected valet mode:

1. Insert your ignition key and turn it to the “ON” position, or start the engine.

2. Flip the valet switch.

3. The LED will glow continuously to indicate that the alarm is in valet mode.

To turn OFF the protected valet mode:

1. Insert your ignition key and turn it to the “ON” position, or start the engine.

2. Flip the valet switch.

3. The LED will turn off to indicate that the alarm is in normal operating mode.

Keyless Entry in Valet Mode: Even if valet mode is on, you will still be able

to remotely control all the convenience features. For instance, simply press but-

ton I as if you were arming or disarming and your car’s doors will lock or un-

lock. You can also use button II to activate an option.

Tampering Warning

Normally, the system immediately sounds its siren at the first inkling of an intru-

sion attempt. However, you may set the system to issue a rapid five-chirp warning

whenever the system detects tampering to the exterior of your vehicle. If there is

any further tampering within the next 30 seconds, or if a door, the hood or trunk is

opened at any time, your system will sound a continuous 125dB siren blast. To

select the mode of your choice, see User-Selectable Features on pages 6-7.

NOTE: Turning on the Tampering Warning feature overrides the FACT fea-

ture, and vice-versa.

FACT™— False Alarm Control and Test

With FACT, you’ll never experience repeated false alarms. If your siren goes off,

DO NOT remotely disarm the system; allow it to run for the full 30-second siren

duration. The system automatically checks for another activated trigger before

sounding the siren a second time. Should the siren sound again, you will know for

sure that someone is tampering with your vehicle.

Automatic Starter Interrupt

The system automatically prevents engine starting while the system is armed. Only

after disarming will the system allow the engine to be started with the ignition key.

Smart AutoTesting™

Each time you remotely arm your vehicle, it will perform a series of tests on all

triggers and sensors. If a trigger malfunction is found, you will be visually and

audibly alerted immediately with 4 chirps and flashes instead of the usual 2. If a

sensor is malfunctioning, you will receive the usual 2 chirps and flashes, then, a

few seconds later, there will be 4 chirps and flashes.

Specific Malfunction Identification: The system not only tells you if the

problem is a trigger or sensor, but it can also indicate the specific trigger or

sensor that is malfunctioning. This feature saves you time and money since

your installer won’t have to spend hours trying to determine where the prob-

lem is. Here’s how it works:

1. You receive the 4-chirp/4-flash signal upon remote disarming.

2. The LED indicator inside the vehicle will be flashing, pause, then repeat.

3. Count the number of blinks in one cycle between pauses (for your conven-

ience, the blink cycle repeats 5 times) and refer to the chart below:

Number of LED blinks between pauses Malfunction

1 blink Vibration/impact sensor or optional sensor

2 blinks Door trigger

3 blinks Trunk or hood trigger

Automatic Malfunction Bypass

To provide the utmost protection even if a system component malfunctions, the

system will automatically bypass the faulty point and arm all other triggers and

sensors until you can have the system serviced by your local Authorized Dealer.

Smart Prior Intrusion Attempt Alert

When you remotely disarm, if you hear 3 chirps instead of the usual one chirp it

means that a trigger or sensor was activated in your absence. When you enter the

vehicle, the LED will blink several times, pause, then repeat the blink cycle 4

more times. Count the number of blinks in one cycle and refer to the chart below:

Number of LED blinks per cycle after disarming Trigger/Sensor Activated

1 blink Vibration/impact sensor or optional sensor

2 blinks Door trigger

3 blinks Trunk or hood trigger

TotalRecall™

The system’s non-volatile memory records the identity of the last activated or

malfunctioning trigger or sensor, which allows your installer to instantly track down a

malfunction and save you servicing costs. To identify the trigger or sensor held in

the system’s non-volatile memory, simply perform the following procedure:

1. With the ignition OFF, flick the valet switch to one side.

2. Press button I to “arm” the system, then again to “disarm.”

3. The LED will blink several times, pause, then repeat the blink cycle 4 times.

4. Count the number of blinks in one cycle and refer to the chart that follows:

Number of LED blinks per cycle Trigger/Sensor that Last Activated or Malfunctioned

1 blink Vibration/impact sensor or optional sensor

2 blinks Door trigger

3 blinks Trunk or hood trigger

LED Status Indicator

The LED on your car’s dashboard or console will inform you of the system status:

LED Condition Meaning

Off System is disarmed

On Protected valet mode

Flashing System is armed

Flashing in cycles Smart AutoDiagnostics/TotalRecall of the last activated trigger or sensor (see pages

3-4) or Smart Prior Intrusion Attempt Alert (see above)

AntiScan

Car thieves use electronic scanners that rapidly transmit one remote control code

after another to defeat ordinary alarms. AntiScan prevents scanners from

disarming your system.

How to Interpret the Chirps and Parking Light Flashes

When you press the remote control buttons, the system will respond with chirps (unless

you have the chirp muting feature turned on) and flashes the parking lights to indicate

the system status. The meaning of these chirp/flash acknowledgments is as follows:

Number of chirps and flashes Meaning

1Disarming of the alarm

2Arming of the alarm

2 and then 4 Armed and there is a sensor malfunction (automatically bypassed)

3Disarmed and there was an intrusion attempt

4Armed and there is a trigger malfunction (automatically bypassed)

Multi-Level Chirp Control

Whenever you wish, you may silence the system’s arm/disarm chirps. The

short-term and one-time chirp muting capabilities are especially valuable when

parking late at night in a quiet residential area. You have several choices:

Extended Chirp Silencing: Lets you completely silence the chirps until you

wish to restore them. See User-Selectable Features on pages 5-6.

Short-Term Chirp Muting: Lets you silence the chirps for a single arm-and-dis-

arm cycle. To enable short-term chirp muting, simply turn the vehicle’s igni-

tion switch rapidly ON then OFF. The next time you arm and later disarm the

system, there will be no chirps. After which, the chirps are restored.

One-Time Remote Chirp Muting: The most simple of all. To remotely arm

or disarm the alarm silently, press buttons I+II on the remote control.

User-Selectable Features

Your XL1000 vehicle security system allows you to set many of its features to

your own personal preferences. We have made the programming procedures very

simple: to make a change, you just flick the valet switch a few times.

The system comes from the factory with all of its features pre-programmed as noted

in the table below and on page 7. To change any of the settings, use the procedure

noted. To restore the feature to its factory setting, just repeat the procedure:

1. Select the feature you wish to program from the table on the following

pages. Note the number of flicks and chirps associated with that feature.

2. Insert your ignition key and turn it to the “ON” position.

3. Immediately flick the valet switch back and forth, counting the number of

chirps you hear. Stop when you reach the appropriate number of chirps

4. If noted, do the “secondary action.”

5. You will hear one or more chirps (as noted in the “program completion con-

firmation” section) to confirm that you have changed the feature setting.

Turn the ignition off.

6. Repeat steps 1-5 for any other features you wish to program.

Programming Table for User-Selectable Features

Feature Factory

setting

# of

flicks &

chirps

Secondary

action

Program

completion

confirmation Result

AutoArming ON 4—1 chirp 3

seconds after

last step

Change state from

ON to OFF or vice-versa

AutoArm

& Lock OFF 5—1 chirp 3

seconds after

last step

Change state from

ON to OFF or vice-versa

Arm/Disarm

Chirp Confir-

mation ON 6—1 chirp 3

seconds after

last step

Change state from

ON to OFF or vice-versa

AutoLock/

AutoUnLock ON 9—1 chirp 3

seconds after

last step

Change state from

ON to OFF or vice-versa

Tampering

Warning OFF 11 —1 chirp 3

seconds after

last step

Change state from

OFF to ON or vice-versa

FACT —

FalseAlarm

Control and

Test ON 12 —1 chirp 3

seconds after

last step

Change state from

OFF to ON or vice-versa

continued . . .

Feature Factory

setting

# of

flicks &

chirps

Secondary

action

Program

completion

confirmation Result

Add a New

Remote to

Channel 1

(arm/disarm) —13 Press remote control button I1 chirp Button I/channel 1 code of

new remote control has

been memorized

Add a New

Remote to

Channel 2

(optional re-

mote

accessory)

—14 Press remote control button II 2 chirps Button II/channel 2 code of

new remote control

has been memorized

Add a New

Remote to

Channel 3 (si-

lent arm/dis-

arm)

—15 Press remote control buttons I+II

(or button III of the optional

4-channel remote control) 3 chirps Button I+II/channel 3 code

of new remote control

has been memorized

Add a New

Remote to

Channel 4

(optional

remote

accessory)

—16 Press remote control button IV

of the optional

4-channel remote control 4 chirps Button IV/channel 4 code

of new remote control

has been memorized

User-Programmable Remote Controls

Eagle will respond to as many as four remote controls regardless of each remote

control’s individual digital coding. Thus, you can buy additional remote controls,

including the super-high-security 4.3-billion-code Premier™ remote controls,

from any Authorized Clifford Dealer. To add a new remote control to the system,

use the procedures noted in the User-Selectable Features section on pages 6-7.

To Erase Unwanted Remote Control Codes

If your remote control is ever lost or stolen, you can erase its digital codes from

the system memory to make sure that the missing remote control can never be

used to disarm your system. Just use the Add a New Remote procedures noted in

the User-Selectable Features section on pages 6-7 for a total of four times (e.g., if

you have one remote control remaining, program it four times; if you have two

remote controls, program each twice).

Inhaltsverzeichnis

Andere Clifford Autoalarmanlage Handbücher

Clifford

Clifford Concept450 Bedienungsanleitung

Clifford

Clifford ACE 7500 Bedienungsanleitung

Clifford

Clifford BlackJax 5 Bedienungsanleitung

Clifford

Clifford AvantGuard 4 Bedienungsanleitung

Clifford

Clifford GP500 Bedienungsanleitung

Clifford

Clifford Cyber 4 Bedienungsanleitung

Clifford

Clifford IntelliGuard 8000 Bedienungsanleitung

Clifford

Clifford Cyber 1 Bedienungsanleitung

Clifford

Clifford G4 System Series Bedienungsanleitung

Clifford

Clifford Sabre Bedienungsanleitung

Clifford

Clifford concept 50 Bedienungsanleitung

Clifford

Clifford 300UK Betriebsanleitung

Clifford

Clifford RS1.1L Bedienungsanleitung

Clifford

Clifford AvantGuard III Bedienungsanleitung

Clifford

Clifford IntellVoice 4 Technisches Handbuch

Clifford

Clifford Matrix RS1.1 Bedienungsanleitung

Clifford

Clifford Tazor 4 Bedienungsanleitung

Clifford

Clifford intellivoice Bedienungsanleitung

Clifford

Clifford Matrix 12 Bedienungsanleitung

Clifford

Clifford intelliguard 700-IQ Bedienungsanleitung

Clifford

Clifford Nova 200LE Bedienungsanleitung

Clifford

Clifford Auto Immobilizer Bedienungsanleitung

Clifford

Clifford BlackJax 4 Bedienungsanleitung

Clifford

Clifford Novell Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung

SECO-LARM

SECO-LARM 300C Bedienungsanleitung

Python

Python 660XP Bedienungsanleitung

Megalarm

Megalarm MEGA 3600 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2011RS Series III Super Rage Bedienungsanleitung