Clifford Cyber 4 Bedienungsanleitung

Toll-Free Technical Support Helpline:

1-800-444-4667

For the latest vehicle wiring information and for

wiring diagrams and servicing information on

older Clifford products:

24-hour AutoFax: 1-800-444-4667

24-hour dealer website: www.clifforddealer.com

Clifford Electronics, Inc.n 20750 Lassen Street n Chatsworth, CA 91311

1-800-824-3208 or 1-818-709-7551 n fax 1-818-407-1743

Table of Contents

Important Information ...........................2

Required Installation Tools ........................2

Standard Features.............................3

System Components............................3

Wiring Diagram ..............................4

Wiring Description for 2-Pin Connector..................5

Wiring Description for 24-Pin Connector.................5

Passenger Compartment Connections...................5

Control Unit and Antenna............................5

Door Trigger/Interior Light Supply........................5

Central Door Locking System...........................6

Door Locks....................................6

Door Lock Diagrams...............................7

LED Status Indicator...............................8

PlainView 2 Coded Valet Switch.........................8

Dual-Zone Piezo Sensor.............................8

Trunk Trigger...................................8

Parking Lights...................................9

Auxiliary A with Selectable Output Type ....................10

Auxiliary B with Selectable Output Type and AutoActivation.........10

Window Control ...............................10

Stator or Ignition Immobilization Circuit....................11

Engine Compartment Connections ....................11

High Output Siren................................11

Hood Trigger.................................. 11

Final Wiring Connections.........................12

SmartPowerUp 2 .............................12

Delayed Courtesy Lights.........................12

Remote Control Button Assignments ...................12

FACT—False Alarm Control and Test...................13

Eight-Event TotalRecall..........................13

Programmable Features.........................14

Using the CliffNet Wizard PRO .........................14

Programming the User-Selectable Features ..................14

User-Programmable Features Table...................... 15

Installer-Programmable Features........................16

Installer-Programmable Features Table ....................16

System Checklist & Troubleshooting.......................17

Important Information

1.DONOTdisconnectthebatterycables!Makebatteryconnectionsbyremovingthelug

nuts from the batteryclampswithoutdetachingtheclampitself.

2.Turn off the interiorlightsorremovethedomelightfusebeforestartingtheinstallation ;

otherwise,leavingthedoor(s)openduringinstallationwilldrainthebattery.

3. Use a voltmeter.DONOTUSEATESTLIGHT!Testlightshaveacurrentdrainthat

willdamagethevehicle’sonboardcomputer,andifyouprobethewrongwire,could

deploy the vehicle’s air bag(s).

4. Make all connections with solder and tape or crimp connectors. DO NOT use bite-type

connectors.

5.Routethesystem’sgroundandpowerwiresdirectlytothevehiclebattery.

6.Keepextensionasshortaspossible.Usesame-gaugewireforshortextensions,largergauge

for longer extensions. DO NOT USE SPEAKER WIRE!

7.Discuss placementoftheLED,valetswitch,windowdecals,etc.withthevehicleowner

prior to installation.

8. DO NOT mount components nor route wires near hot or moving vehicleparts.Clifford

componentsmustnotimpedevehicleservicingoroperation.

9.DO NOT mount any Clifford sensor in the engine compartment.

10.Follow the system’s Sequence of Installationtoensureproperinstallationandtesting.

11.Place the owner’s manual in the glove box.

Note: Clifford Electronics’ web site for Authorized Clifford Dealers has

detailed descriptions of wire colors and locations for most foreign and

domestic vehicles. Installation diagrams and programming procedures for

olderCliffordproductsarealsoavailable.Justvisitwww.clifforddealer.com

for assistance 24-hours per day.

Required Installation Tools

Voltmeter (set to “DC Volt”)

Wire crimper

Wire stripper

Electric drill and bits

Phillips screwdriver

Crescentwrench

Vinyl tubing

Rubbergrommet

Convoluted tubing

Shrinktubing

Solder gun and solder

Heat gun

Standard Features of the Cyber 4

System Components

The Cyber 4 installation kit contains the following components:

One Prewired 24-pin connector harness One Antenna

One Prewired 2-pin connector harness One High Output Siren

One Cyber 4 Control Unit One PlainView 2 Coded Valet Switch

One Hardware Kit One Prewired LED

One Dual Zone Piezo Sensor One User’s Manual

Two Remote Transmitters Two Clifford Window Decals

nLifetime Warranty

nTwo ACG™ 2 Remote Controls

nAudible Low Remote Battery Warning

nBuilt-In Starter or Ignition Immobilizer

nFACT—False Alarm Control & Test

nRemote Siren Silencing

nDual Zone Piezo Sensor™

nDual-Mode “Chirp” Silencing

nPatented UltraSecure Coded Valet

Mode™

nOptional DataPort™ Interface to Your

Own PC

nPoint-and-Click Feature Programming

nComplete System Diagnostics

At-A-Glance

nHigh-Output Siren

nRemote Door Locking/Unlocking with

built-in relays

nRemote Panic with Smart

Locking/Unlocking

nBuilt-In Dual Parking Light Flasher

with Onboard Relay

nRemote Courtesy Lighting

nRemote Keyless Entry and Accessory

Activation Even in Valet

nPatented Smart AutoTesting™

nSmart Remote Trunk Release

nUser-Selectable AutoArming

nUser-Selectable AutoArm & Lock

nInstant AutoArm Bypass

nPatented Malfunction AutoBypass™

nPatented SmartPowerUp™ 2

nMultiVehicle Control with One Remote

nEight-Event TotalRecall™

nSmart Prior Intrusion Attempt Alert

nPatented Remote Control Code

Learning and MultiRemote Recognition

nClear All Remotes

nLED Status Indicator with Automatic

Battery-Saving Mode

nSecureAccess™ Programming

nPre-Loomed Wiring

n2 Accessory Outputs with Selectable

Output Type, One with Selectable

AutoActivation for All-Close Windows

nIntegrated Electronic Timer for Remote

Headlight Activation or Timed Turbo

Cooldown

nInstaller-Selectable Door Ajar/Delayed

Courtesy Lights

nPrewired LED, Sensor and PlainView 2

Switch Connectors

Wiring Description for 2-Pin Connector

Pin Wire ColorConnects to

1White/Red Starter or Ignition Interrupt

2White/Red Starter or Ignition Interrupt

Wiring Description for 24-Pin Connector

Pin Wire ColorConnects to

1VioletLED output (+)

2Green Armed output (-)

3Blue Sensor input warning zone (-)

4White Valet Switch input (-)

5Gray/Blue Auxiliary B output (-)

6Gray/VioletAuxiliary A output (-)

7White/Brown Ignition Input

8OrangeOptional Sensor (-)

9Gray Door trigger input (+) or (-)

10 Gray/Yellow Trunk and hood trigger input (-)

11 OrangeDual-Zone Piezo Sensor input trigger zone (-)

12 Yellow Siren output (-)

13 Black Battery Negative (ground for the Dual-Zone Piezo Sensor, optional

sensor and LED connectors, Valet Switch)

14 Red Battery positive with 5 Amp fuse

15 Brown/Red Interior light supply

16 Red/WhiteBattery positive with 20 Amp fuse

17 Brown Parking light output (+)

18 BrownParking light output (+)

19 Gray/Orange Door unlock normally closed

20 Gray/Green Door lock normally closed

21 White/Orange Door unlock comm.

22 Red/Green Door lock normally open

23 Red/OrangeDoor unlock normally open

24 White/Green Door lock comm.

Passenger Compartment Connections

Control Unit and Antenna

The Cyber 4 control unit must be installed inside the vehicle. Under no

circumstances should the unit be installed underthe hood orothersimilarly

hostile environment.

1.Select an area behind the dash to mount the control unit using wire ties, but do not

permanently affix it until all wiring and testing is complete.

2.Run the antenna either up the window pillar or under the dash, away from metal. Do not

fold the excess cable or antenna wire. Do not make hard, sharp bends.

Door Trigger/Interior Light Supply

The Cyber 4 has self-programming door trigger polarity. Door triggers on most autos are

negative (except most Rolls-Royce and Ford autos). To determine door trigger polarity, use

thefollowing procedure:

1.Find the wire coming off the rear of the vehicle door switch.

2. Connect the negative voltmeter lead to ground.

3.Find the one wire that shows +12 volts when the switch is pressed in and 0 volts when

released. This is a negative trigger door wire.

4.If you don’t get the indications noted in step 3, find the one wire that shows 0 volts when

the switch is pressed in and +12 volts when released. This is a positive trigger door wire.

Passenger Compartment Connections (Continued)

Door Trigger/Interior Light Supply (Continued)

5. Connect the system’s thin GRAY wire to the door wire.

6.If the trigger wire is negative, connect the system’s BROWN/RED interior light supply

wire to ground. If the trigger wire is positive, connect the system’s BROWN/RED interior

light supply wire to the RED/WHITE wire.

NOTE: Clifford Electronics’ web site for Authorized Clifford Dealers has

detailed descriptions of wire colors and locations for most foreign and

domestic vehicles. Installation diagrams and programming procedures for

olderCliffordproductsarealsoavailable.Justvisitwww.clifforddealer.com

for assistance 24-hours per day.

Central Door Locking System

Pleaserefer to the Door Locks section below for information on circuit types and connections.

When adding an IntelliStart 4 to the Cyber 4, it is recommended that RPM-depending door

locking be selected. The RPM-dependent door locking feature is only available with the

addition of the IntelliStart 4.

Door Locks

WARNING:Ifthepowerdoorlocksdonotoperateproperlywhenthesystem

isarmedand dis armed,DONOTUSETHE VE HICLE’SDOORLOCKSWITCH! If

the control unit’s door lock wires are miswired, permanent damage to the

controlunitortothecar’selectricalsystemanddoorlockservoswillresult.If

yourequireassistance,calltheCliffordTechnicalSupportHelplinePRIORto

wiring the door locks.

Cyber 4 systems provide power door lock interface capabilities and are able to interface with

any power door lock configuration including some Mercedes Benz and Audi vehicles that

require a 3-second lock pulse (pulse duration is installer-programmable) and with any car

’Volkswagens and Nissans, for example) that require double unlock pulse. If the vehicleisnot

equipped with power door locks, you may optionally add up to four #60-516DoorLock

Servos.

Determining the Door Lock System Type

1.Remove the door lock switch on the driver’s side of the vehicle to reveal the switch wires.

a.If there are four or more wires, make the connections shown in Diagram 4 for

reverse polarity.

b.If there are three wires, proceed to step 2.

c. If the vehicle is a Nissan and it does not have a door lock switch, find the single

wire in the driver’s kick panel that shows ground when the locks are unlocked and

“open” when the locks are locked. Cut this wire and make the connections shown

in Door Lock/Unlock Diagram 3.

2.Connect the negative voltmeter lead to ground and probe each wire while

locking/unlocking. If the voltmeter show +12v while activating the switch, make the

connections shown in Door Lock/Unlock Diagram 1 for positive trigger. Otherwise, go to

step 3.

3. Repeat step 2 with the negative voltmeter lead connected to +12v. If the voltmeter shows

+12v while activating the switch, make the connections shown in Door Lock/Unlock

Diagram 2 for negative trigger.

4. Locks controlled from the driver’s door key require installation of just one #60-516 servo

in the driver’s door. Vehicles without factory power locks require a servo in each door.

Mount the servo(s) and make the connections shown in Door Lock/Unlock Diagram 5.

Passenger Compartment Connections (Continued)

5.On a vacuum-pump-type Mercedes Benz or Audi, make the connections shown in Door

Lock/Unlock Diagram 6, then (if 1989 or older) program the system for a 3-second lock pulse.

6.The Cyber 4 can also provide double lock and unlock pulses (+ or -) required by some

vehicles (such as some Nissans’ Volkswagens and Audis). Wire the door locks following

the steps above and select the 2x lock or unlock feature in installer-programming.

Passenger Compartment Connections (Continued)

LED Status Indicator

Select a prominent location on the dash or console visible through all windows. Discuss

placement with the owner.

1. Verify there is adequate space to accommodate the LED, then drill a 5/16” (8mm) hole

and route the wires through it.

2.Mate the LED connectors to the VIOLET and BLACK wire connectors as shown in the

diagram on page 4.

3. Press the LED into place.

PlainView 2 Coded Valet Switch

1. Discuss placement of the switch with the vehicle owner and avoid placing the switch

where it can be pressed accidentally.

2.Verify there is adequate space behind the selected location to accommodate the switch.

3. Drill a 5/16” (8mm) mounting hole, then insert the wires through the hole and mount the

switch.

4.Mate the switch’s locking connectors to the WHITE and BLACK locking connector.

5. Remove the adhesive backing and press into place.

Dual-Zone Piezo Sensor

Mount the Dual-Zone Piezo Sensor in the passenger compartment, not in the engine

compartment.

1.Firmly mount the sensor near the base of the steering column (if the steering column has a

rotating sleeve, firmly screw the sensor to the interior firewall, kick panel or trunk wall).

Make certain that the adjustment screw is accessible.

2.Mate the sensor to the connector on the wireloom from the control unit with the BLACK,

RED, ORANGE and BLUE wires.

Trunk Trigger

Vehicles with a ground-switching trunk light will interface directly with the Cyber 4 (on positive

switchingRolls-Royce vehicles, use a relay to invert polarity). The switch may be located in or

near the trunk latch or at the trunk light. If a switch cannot be located, you must add a pin

switch in a location away from water channels.

NOTE:Ifthevehiclehasadashboardtrunkajarindicator,installa1Adiode

between the light and switch with the diode band pointing toward the

switch.

1.Connect the GRAY/YELLOW wire to the trunk switch (between the diode and switch if

you added a diode).

Andere Handbücher für Cyber 4

Inhaltsverzeichnis

Andere Clifford Autoalarmanlage Handbücher

Clifford

Clifford SE 3030 Bedienungsanleitung

Clifford

Clifford Polaris II Bedienungsanleitung

Clifford

Clifford Model RSX3.5 Bedienungsanleitung

Clifford

Clifford Polaris 4 Bedienungsanleitung

Clifford

Clifford Intelliguard Millenia Bedienungsanleitung

Clifford

Clifford 4806X Bedienungsanleitung

Clifford

Clifford Eagle II Bedienungsanleitung

Clifford

Clifford 30 Bedienungsanleitung

Clifford

Clifford Level Four Bedienungsanleitung

Clifford

Clifford 5706X Bedienungsanleitung

Clifford

Clifford Ultramax XL3500 Bedienungsanleitung

Clifford

Clifford Concept 100 Bedienungsanleitung

Clifford

Clifford 300 Bedienungsanleitung

Clifford

Clifford Bullet 2 Bedienungsanleitung

Clifford

Clifford 5906V Bedienungsanleitung

Clifford

Clifford AvantGuard 2 Bedienungsanleitung

Clifford

Clifford Arrow 5.1 Bedienungsanleitung

Clifford

Clifford CONCEPT 470 Bedienungsanleitung

Clifford

Clifford Prime Level Three Security Upgrade Package Bedienungsanleitung

Clifford

Clifford Concept 600 Bedienungsanleitung

Clifford

Clifford Responder LE 5806X Bedienungsanleitung

Clifford

Clifford Matrix RS2 Bedienungsanleitung

Clifford

Clifford IntellVoice 4 Technisches Handbuch

Clifford

Clifford Polaris 4 Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Ultra Start

Ultra Start 450 SERIES Bedienungsanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Excalibur

Excalibur AL-1860-EDPB Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung

SECO-LARM

SECO-LARM 300C Bedienungsanleitung

Python

Python 660XP Bedienungsanleitung