Code Alarm CATX130 Betriebsanleitung

Model CATX130

Programming Guide

The keychain transmitters included with the system have been pre-programmed at the factory,

with each button pre-assigned to control a specific function of the system.

The system will store codes from up to 8 different transmitters. If a 9th transmitter is

programmed to the system, then the first transmitter programmed to the system will be

erased from the system’s memory.

To program new or additional transmitters, the alarm must be disarmed and out of valet mode:

1. Open the drivers door (verify that the vehicle’s interior light turns on.

2. Turn the ignition key to the ON or RUN position.

3. Press and hold the emergency override button

3a. After 10 seconds the horn will honk three (3) times. This indicates

that the system has entered transmitter programming mode.

4. Release the emergency override button.

5. Press the LOCK icon button on the remote transmitter to be programmed.

5a. The horn/siren will sound 1 time, indicating that the system has

“learned” that remote transmitter.

6. Repeat step 5 for any additional remote transmitters.

Deleting Lost or Stolen Remote Controls from Your System

If one of your remote controls is lost or stolen, follow these instructions IMMEDIATELY to

remove the control code from your system.

1. Have all remaining remote controls available.

2. Enter the control programming mode by following steps 1 - 5 of Adding Remote Controls

to Your System.

3a. If you have only one remaining remote control, press the

LOCK button on that remote control eight (8) times, pausing

at least 1 second in between each press. The horn must

“honk” each time you press the LOCK button.

3b. If you have two remaining remote controls, press the LOCK

button on each remote control four (4) times, pausing at least

1 second in between each press. The horn must “honk” each

time you press the LOCK button.

3c. If you have three remaining remote controls, press the

LOCK button on two of the remote controls three (3) times, then press the

LOCK button on the remaining remote control twice. Pause at

least 1 second in between each press. The horn must “honk”

each time you press the LOCK button.

4. Turn the vehicle ignition off to exit the programming mode. When you are finished, the lost

or stolen remote control will no longer operate your system.

Changing the Remote Control Battery

The 12-volt alkaline battery supplied in your remote

transmitter should last approximately one year, depending on

usage. When the battery begins to weaken, you will notice a

decrease in range, or the distance from your vehicle that

your remote transmitter will operate. Follow the instructions

below to change the remote transmitter battery.

For Customer Service and Product information Call

1-800-421-3209

1. Insert the edge of a coin into the slot at the side of the

remote control. Twist the coin to pry the remote control

halves apart.

2. Remove the old battery and replace with a new one.

Be sure to observe the (+) and (-) signs in the battery

compartment.

3. Carefully snap the case halves back together, then test

the remote control.

Model CATX130

Programming Guide

Inhaltsverzeichnis

Andere Code Alarm Autoalarmanlage Handbücher

Code Alarm

Code Alarm Professional caSECRS Bedienungsanleitung

Code Alarm

Code Alarm CSI-300 Bedienungsanleitung

Code Alarm

Code Alarm Professional Series CA 1550 Bedienungsanleitung

Code Alarm

Code Alarm CA-125 Bedienungsanleitung

Code Alarm

Code Alarm Power Elite PC 4100 Bedienungsanleitung

Code Alarm

Code Alarm CATX630 Betriebsanleitung

Code Alarm

Code Alarm ca 5152 Bedienungsanleitung

Code Alarm

Code Alarm 420A Bedienungsanleitung

Code Alarm

Code Alarm ca6355E Bedienungsanleitung

Code Alarm

Code Alarm CA 170 Bedienungsanleitung

Code Alarm

Code Alarm CATX110 Betriebsanleitung

Code Alarm

Code Alarm Ca 1053 Bedienungsanleitung

Code Alarm

Code Alarm CA-120 Bedienungsanleitung

Code Alarm

Code Alarm CA 6551 SST Bedienungsanleitung

Code Alarm

Code Alarm CA-330 Bedienungsanleitung

Code Alarm

Code Alarm Procomp Bedienungsanleitung

Code Alarm

Code Alarm CA 210 Bedienungsanleitung

Code Alarm

Code Alarm CA-160 Bedienungsanleitung

Code Alarm

Code Alarm ca1554 Bedienungsanleitung

Code Alarm

Code Alarm CSI-200 Bedienungsanleitung

Code Alarm

Code Alarm ca 1151 Bedienungsanleitung

Code Alarm

Code Alarm ca 2051 Bedienungsanleitung

Code Alarm

Code Alarm CA 420A Bedienungsanleitung

Code Alarm

Code Alarm CA-500 Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Ultra Start

Ultra Start 450 SERIES Bedienungsanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Excalibur

Excalibur AL-1860-EDPB Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung