Code Alarm Ca 1552 Professional Series Bedienungsanleitung

1ca1552.2011AudiovoxElectronicsCorporation.Allrightsreserved.

PROFESSIONAL

SERIES

ca 1552

Owner’s Guide

IMPORTANT NOTE: The operation ofthe Securityand Convenience System asdescribed inthis manual is

applicableto most vehicles.However, due tothe configuration ofsome vehicles, somefunctionsAND/OR

SAFETYPRECAUTIONS maynot apply.Please seeyour installingdealer formore information.

Deluxe Vehicle Security and

Keyless Entry System with 2 Way

Confirming LCD Remote Control

2 ca1552.2011AudiovoxElectronicsCorporation.Allrightsreserved.

Table of Contents

Using Your Remote Control ...............................................................3

Arming the Security System ............................................................3

Passive Arming Bypass ...................................................................3

Bypassing the Shock Sensor ..........................................................3

HiddenAlarm Function......................................................................3

Disarming the Security System........................................................3

Two Stage Door Unlock (optional) ...................................................4

Activating Trunk Release (optional) ................................................4

Activating Optional AUX 1 (optional) ...............................................4

Entering AUX Mode and Activating Additional AUX Outputs ..........4

Using the Progressive Car Finder Feature......................................5

Using the Personal Protection Alarm ...............................................5

Programmed Transmitter Notification ..............................................5

Valet Mode ........................................................................................5

EliminatingArm / Disarm Notification Chirps ....................................5

Manually Overriding the Security System .......................................6

Car Jack Mode ..................................................................................6

LED and Siren/Horn Indications ......................................................... 7

Additional 2-Way LCD Remote Control Functions ........................ 8

LCD Remote Control ICON’s ............................................................10

Transmitter Button Functions ......................................................... 11

Replacing Remote Control Batteries.............................................13

Warranty Information.........................................................................14

3ca1552.2011AudiovoxElectronicsCorporation.Allrightsreserved.

Arming the Security System

To arm the system, exit the vehicle, close all doors, then press the button. The

parking lights will flash 2 times, indicating the system is armed, has locked the

doors (if equipped and connected) and activated the starter disable feature. The

LED status indicator will blink steadily, once per second.

NOTE: The system is equipped with a feature called Silent Choice. If enabled, the

system requires a second press of the button to activate an audible arming

response from the vehicle.

Passive Arming Bypass

If passive arming is enabled on your system, while the system is disarmed, press

+ , the system will respond with 1 chirp and the LED will turn on. The

security system will remain in this temporally bypassed state for as long as you

wish. To exit passive bypass, press the or button and the system will return

to normal status.

Bypassing The Shock Sensor

To arm the system and ignore the shock sensor press button, then within 5

seconds press + , the system will respond with 1 long chirp.

NOTE: The system will only change the shock sensor setting for one arm cycle

and will be defaulted back to normal operation the next time the system is armed.

Hidden Alarm Function

Press the button first, within 3 seconds press the button to activate the

hidden alarm function. The security system will arm with “Hidden Alarm Function”

in which the siren / horn will be silenced if the system is triggered.

Disarming the Security System

To disarm the system press the button. The parking lights will flash 1 time,

indicating the system is disarmed and has unlocked the doors (if equipped and

connected).

NOTE: The system is equipped with a feature called Silent Choice. If enabled, the

system requires a second press of the button to activate an audible disarming

response from the vehicle. If your system is set up for 2 step unlock, a third press

of unlock will activate the audible response.

*Throughout this manual, ‘press’ refers to pressing for less than 1 second; ‘press and hold’ refers to pressing for more

than2seconds.

Using Your Remote Control

4 ca1552.2011AudiovoxElectronicsCorporation.Allrightsreserved.

Two Stage Door Unlock (Optional)

If this feature is enabled on your system, pressing the button one time will

unlock only the driver’s door. Press again within three seconds to unlock the

remaining doors.

Activating the Trunk Release Feature (Optional)

If this feature is enabled on your system, pressing and holding the button for 3

seconds will open the vehicle’s trunk or hatch.

Activating Optional AUX 1 (Optional)

If this feature is enabled on your system, pressing the and buttons

simultaneously will activate an optional feature. This feature can be programmed for

a wide range of functions like power window or sunroof automation, please consult

your installing dealer to determine the functionality of your system.

Entering AUX Mode and Activating the Additional AUX 2 - 5 Outputs

(Optional)

To access the additional AUX outputs, AUX 2, AUX 3, AUX 4, and AUX 5, you must

first enter the transmitters AUX Mode. This will “shift” the functions of the transmitter

buttons from their standard operation to control of the AUX outputs.

AUX Mode - 1 Way transmitter: Press and Hold and for 2

seconds, the transmitter LED will flash 1 time. AUX Mode will remain active

for 15 seconds. AUX Mode will exit after 15 seconds of inactivity or by

pressing and again for 2 seconds, the transmitter LED will flash 2

times to confirm exit.

AUX Mode - 2 Way transmitter: Press and Hold for 2 seconds, the

transmitter LCD screen will display “AU”. AUX Mode will remain active

for 15 seconds. AUX Mode will exit after 15 seconds of inactivity or by

pressing again for 2 seconds.

Activating outputs while in AUX Mode:

AUX 2: Press and Hold for 3 seconds.

AUX 3: Press and Hold for 3 seconds.

AUX 4: Press and Hold for 3 seconds.

AUX 5: Press and Hold for 3 seconds.

5ca1552.2011AudiovoxElectronicsCorporation.Allrightsreserved.

Using the Progressive Car Finder Feature

Press the button to locate your vehicle. The system will sound 5 times at low

volume, increasing in volume each time the button is pressed.

Using the Personal Protection Alarm (Panic)

Press and hold the button for 3 seconds to activate the personal protection alarm.

During panic mode, the normal function of the transmitter buttons will be suspended.

The transmitter’s and buttons can be used to lock and unlock the door (if the

option is installed). To stop the alarm, press and hold the button on the transmitter

again for 3 seconds. The system will automatically stop after 30 seconds.

Programmed Transmitter Notification

As a security precaution each time the vehicle’s ignition is turn on the status LED

light with flash the number of transmitters programmed into the system. This helps

to identify unauthorized transmitters from accessing your vehicle. If you believe an

unauthorized transmitter has been programmed to your system, contact your

installing dealer for assistance.

Valet Mode

When valet mode is activated the status LED will light solid, and all security

functions will be disabled. To enter or exit valet mode simply follow the 4 steps

outlined below:

1. Turn the vehicle’s ignition ON.

2. Push and hold the programming/valet button.

3. The LED will turn on solid when valet mode is active

4. Release the programming/valet button.

Eliminating Arm / Disarm Notification Chirps

System ARM/DISARM chirps can be toggled ON or OFF without entering the

programming feature banks.

1. Turn the ignition ON then OFF.

2. Press and release the valet/programming button 3 times. The system

will respond with 1 chirp for ON or 2 chirps for OFF.

6 ca1552.2011AudiovoxElectronicsCorporation.Allrightsreserved.

Manually Overriding the Security System

Your system can be disarmed without the use of the transmitter. This is

necessary, since you will need the ability to operate your vehicle if the transmitter

is lost or its battery fails. To by-pass the alarm system;

1. Open the vehicle door. The alarm will sound.

2. Turn the ignition key to the ON position.

3. Within 10 seconds, press and release the valet push button switch.

The alarm system will stop sounding and enter the (by-passed) mode. You can

now start and operate the vehicle normally.

Car Jack Mode

This feature must be turned on in system programming, please consult your

installing dealer.

Triggering Car Jack mode: While the ignition is ON and press and hold + for 2

seconds, the parking lights will flash 1 time and the system will act as follows;

1. 50 seconds after being triggered the siren will chirp for 15 seconds,

during this 15 seconds you will be alerted to push the valet button to

turn off Car Jack mode. If Car Jack mode is not turned off at this time it

will advance to the next step.

2. Following the 15 second chirps (total time now 65 seconds) the siren

will go into full sound and the parking lights will start flashing.

3. 90 seconds after trigger in, addition to the siren and parking lights, the

system will activate the starter kill. THE SYSTEM WILL REMAIN IN THIS

STATEUNTILTHEBATTERYISDEPLETED.

OVERRIDETHESYSTEMTOTURNOFFCARJACKMODE:Turnthe ignition OFF

then ON and press the valet button within 10 seconds.

7ca1552.2011AudiovoxElectronicsCorporation.Allrightsreserved.

LED and Siren/Horn Indications

LED Display Indications

LED Function

OFF DISARMED

SLOW FLASH ARMED

FAST FLASH PASSIVEARMING

ON(SOLID) VALETMODE

2 FLASH... PAUSE ZONE2TRIGGER,HOOD/TRUNK

3 FLASH... PAUSE ZONE3TRIGGER,DOOR

4 FLASH... PAUSE ZONE4TRIGGER,SHOCK

5 FLASH... PAUSE ZONE5TRIGGER,IGNITION

Siren/Horn Indications

Chirps Function

1 DISARM

2 ARM

3 DOORAJARUPONARMING

4 DISARM/TRIGGERED

5 CARLOCATOR

Parking Light Flash Indications

Flashes Function

1 DISARM

2 ARM

3 DISARM/TRIGGERED

5 CARLOCATOR

8 ca1552.2011AudiovoxElectronicsCorporation.Allrightsreserved.

Check Vehicle Status

Press and release 2 times then press within 3 seconds, the transmitter will

display the current status of the vehicle.

Display Illumination

Press and hold the button for 1 second. The display will illuminate for 5

seconds.

Melody / Vibration Mode

To have the remote control vibrate, play a melody tone or both each time it receives

a response from the vehicle press and release then press and hold for 2

seconds.

Button Beeps

To toggle button beeps on or off press and release then press and hold for 2

seconds.

Battery Save Mode

While in POWER SAVE MODE the 2-way LCD transmitter will NOT look for any

incoming signals from the main unit until a button is pressed. The LCD screen will

display SAVE to indicate that power save mode is ON. To enter power save mode

press and hold for 5 seconds.

Clear Flashing Icons and Melody Sound

Press the button 3 times within 3 seconds. This will clear the melody sound and

flashing icons on the LCD screen.

Stopping LCD Trigger Melody

To stop the alarm trigger melody if the system has been triggered WITHOUT

disarming the system, press any button one time only, this will not send a

command to the vehicle at this time and the alarm will continue to sound.

Additional 2-Way LCD Remote Control Functions

9ca1552.2011AudiovoxElectronicsCorporation.Allrightsreserved.

Button Lock

Press and release then press hold the for 2 seconds to toggle the button lock

on or off. When the button lock is active, the remote control will beep/vibrate 2

times when a button is pressed indicating it is locked.

Illumination

Press and release 2 times then press and hold for 2 seconds to toggle

illumination on or off. When on, the display will illuminate when it receives or

sends a command.

2 Car Mode

To control a second security system enter 2 car mode by pressing then press

and together for 3 seconds. When the icon appears on the transmitter’s LCD

screen it will control the second security system. Use the same method to exit 2

car mode and resume control of the original vehicle’s security system.

NOTE: A second security system must be installed and the LCD transmitter must be

learned to it before this feature will operate the additional system.

Parking Meter Countdown

The parking meter countdown timer has 6 preset times, to access the preset times

and begin countdown press and release then press and hold for 2 seconds,

each additional press of will increase the countdown time.

Adjusting the Clock and Timer Settings

The clock, alarm clock and programmable countdown timer are accessed through

the Function Menu. Press and hold for 3 seconds to access the function menu,

once you have accessed the feature menu press and release to scroll through

each feature and follow the steps below to adjust the settings for each. Press and

hold for 2 seconds to exit the menu.

Clock Hour Press to increase or to decrease

ClockMinute Press to increase or to decrease

Alarm Clock Hour Press to increase or to decrease

Alarm Clock Minute Press to increase or to decrease

Alarm Clock ON / OFF Press to turn ON or to turn OFF

Countdown Timer Hour Press to increase or to decrease

Countdown Timer Minute Press to increase or to decrease

Countdown Timer ON / OFF Press to turn ON or to turn OFF

10 ca1552.2011AudiovoxElectronicsCorporation.Allrightsreserved.

LCD Remote Control ICON’s

LOCK UNLOCK

SYSTEM ARMED VALET MODE

TRANSMITTING

TRUNK TRIGGER DOOR TRIGGER

FULL SHOCK TRIGGER

IGNITION ON/TRIGGER

2 CAR MODE

BATTERY INDICATOR BATTERY SAVE MODE

VIBRATE/SILENT MODE

HOOD TRIGGER

SYSTEM TRIGGER TIME COUNT DOWN

MELODY MODE

TIME DISPLAY

ALARM CLOCK

AUX 1 OUTPUT

AUX MODE

AUX 5 OUTPUT

AUX 4 OUTPUT

AUX 3 OUTPUT

AUX 2 OUTPUT

Andere Handbücher für ca 1552 Professional Series

Inhaltsverzeichnis

Andere Code Alarm Autoalarmanlage Handbücher

Code Alarm

Code Alarm Professional 1000 Bedienungsanleitung

Code Alarm

Code Alarm CA 310 Bedienungsanleitung

Code Alarm

Code Alarm CA 521 Bedienungsanleitung

Code Alarm

Code Alarm CA 671 Bedienungsanleitung

Code Alarm

Code Alarm CA1B5 Bedienungsanleitung

Code Alarm

Code Alarm CA 650 Bedienungsanleitung

Code Alarm

Code Alarm CA-640 Bedienungsanleitung

Code Alarm

Code Alarm CA611 Bedienungsanleitung

Code Alarm

Code Alarm Ca 1053 Bedienungsanleitung

Code Alarm

Code Alarm CA 421 Bedienungsanleitung

Code Alarm

Code Alarm F50 Bedienungsanleitung

Code Alarm

Code Alarm CA 170 Bedienungsanleitung

Code Alarm

Code Alarm Car Alarm CA-310 Bedienungsanleitung

Code Alarm

Code Alarm CA-120 Bedienungsanleitung

Code Alarm

Code Alarm PROFESSIONAL SERIES Bedienungsanleitung

Code Alarm

Code Alarm CA- 550 Bedienungsanleitung

Code Alarm

Code Alarm CA 170 Bedienungsanleitung

Code Alarm

Code Alarm ELITE Series Bedienungsanleitung

Code Alarm

Code Alarm CA100 Bedienungsanleitung

Code Alarm

Code Alarm CATX510 Betriebsanleitung

Code Alarm

Code Alarm Professional Series CA 1550 Bedienungsanleitung

Code Alarm

Code Alarm PROFESSIONAL CA 1045 Bedienungsanleitung

Code Alarm

Code Alarm F20 Bedienungsanleitung

Code Alarm

Code Alarm Professional caSECRS Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Ultra Start

Ultra Start 450 SERIES Bedienungsanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Excalibur

Excalibur AL-1860-EDPB Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Code Alarm ca 1552 Professional Series Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken