Code Alarm Professional ca6153 Bedienungsanleitung

PROFESSIONAL

SERIES

Security and Remote Start Installation Guide

for models:

ca6153

2ca6153 revA

Before You Begin ...................................................................................... 4

Wire Connection Guide ........................................................................... 5

4 Pin Main Harness ................................................................................... 7

6 Pin Start Harness ................................................................................... 8

6 Pin Output Harness ............................................................................. 10

8 Pin Input Harness ................................................................................. 11

4 Pin Alternate Output Harness ............................................................. 14

3 Pin Door Lock Output Harness ........................................................... 15

Additional Ports ...................................................................................... 19

Antenna / LED / Programming Port ....................................................... 19

DBI Port .................................................................................................... 19

Telematic Interface Port .......................................................................... 19

Set Up & Programming .......................................................................... 20

Transmitter Programming ........................................................................ 20

Manual Feature Programming ................................................................. 20

Programming Feature Banks .................................................................. 21

Tach Programming .................................................................................. 24

Smart Tachless Mode ............................................................................. 24

Adjusting the Shock Sensor .................................................................. 25

Testing the Shock Sensor ...................................................................... 25

Chirp Delete - User Accessible .............................................................. 25

Dome Light Delay / Theater Dimming ..................................................... 25

Table of Contents

Feature Descriptions ............................................................................. 26

Transmitter Button Functions ............................................................. 32

Security Trigger Zones ......................................................................... 33

Remote Start Shutdown Diagnostics ................................................ 33

System Layout ......................................................................................... 34

4ca6153 revA

FOR AUTOMATIC TRANSMISSION VEHICLES ONLY.

PROFESSIONAL INSTALLATION

STRONGLYRECOMMENDED

Installation Precautions:

Roll down window to avoid locking keys in vehicle

during installation

Avoid mounting components or routing wires near

hot surfaces

Avoid mounting components or routing wires near

moving parts

Tape or loom wires under hood for protection and

appearance

Technical Support (800) 421-3209

or go to

http://techservices.codesystems.com

Use a Digital Multi Meter for testing and verifying

circuits. DO NOT USE A TEST LIGHT, OR

"COMPUTER SAFE PROBE" as these can set off air

bags or damage vehicle computers.

Use grommets when routing wires through metal

surfaces

BEFORE YOU BEGIN

6 Pin Start Harness

4 Pin Main Harness

6 Pin Output Harness

1WHITE/RED PARKING LIGHT INPUT

2WHITE PARKING LIGHT OUTPUT

3BLACK GROUND

4BROWN SIREN OUTPUT ( + )

4 PIN MAIN

1PURPLE STARTER OUTPUT - MOTOR SIDE

2RED BATTERY 12V ( + )

3ORANGE ACCESSORY 1 ( + )

4PINK/WHITE IGNITION 2 ( + )

5RED/WHITE BATTERY 12V ( + )

6PINK IGNITION 1 ( + )

6 PIN START

1BROWN/BLACK HORN OUTPUT ( - )

2BLUE/BLACK START STATUS / ACTIVE OUTPUT ( - )

3VIOLET/BLACK AUX 1 OUTPUT ( - )

4RED/WHITE TRUNK RELEASE OUTPUT ( - )

5LT GREEN/BLACK FACTORY DISARM / PULSE BEFORE START ( - )

6ORANGE GROUND WHEN ARMED OUTPUT ( - )

6 PIN OUTPUT

6ca6153 revA

8 Pin Input Harness

3 Pin Lock Output Harness

4 Pin Alternate Output Harness

1BLUE UNLOCK ( - )

2OPEN

3GREEN LOCK ( - )

3 PIN

LOCK

1BLACK/YELLOW PULSE DURING CRANK ( - )

2GREEN/WHITE PULSE AFTER SHUTDOWN ( - )

3LT BLUE FACTORY ARM / PULSE AFTER START ( - )

4LT GREEN/BLACK FACTORY DISARM / PULSE BEFORE START ( - )

4 PIN

ALTERNATE

OUTPUT

3 BLACK GROUND

Connect the BLACK wire to a solid chassis ground point using a ring terminal and

self tapping screw (not supplied). Scrape away paint from the grounding point to

ensure a good connection. The recommended grounding point is a metal surface

in the driver’s side kick panel area.

NOTE: Do not ground the BLACK wire with any other vehicle components.

4 Pin Main Harness

1 WHITE/RED PARKING LIGHT INPUT

2 WHITE PARKING LIGHT OUTPUT

Locate the parking light output wire at the vehicle’s light switch.

Verification: This wire registers positive voltage when the parking lights are

turned on.

Positive switching Parking Lights:

Connect the WHITE/RED wire to a 15 Amp max fused battery source.

Connect the WHITE wire to the parking light output wire.

Negative switching Parking Lights:

Connect the WHITE/RED wire to a good chassis ground.

Connect the WHITE wire to the parking light output wire.

4 BROWN SIREN OUTPUT ( + )

Locate a suitable mounting location in the engine compartment for the siren, away

from moving parts.

With the bell of the siren aiming downwards, secure the siren in place using self

tapping screws, being careful not do drill into any hoses, wiring or components.

Connect the BLACK siren wire to a chassis ground using a ring terminal and self

tapping screw (not supplied).

Route the BROWN siren output wire from the control module through the firewall

and connect to the RED wire on the siren.

NOTE: Be sure to loom the siren wires, and seal the grommet.

8ca6153 revA

3 ORANGE ACCESSORY 1 ( + )

Locate the vehicle’s accessory wire at the ignition switch.

Verification: This wire registers voltage when the key is turned to ACC

(Accessory) and the ON (or RUN) position. The voltage drops out when the

key is turned to the START(or CRANK) position.

Connect the ORANGE wire to the vehicle’s accessory wire.

6 Pin Start Harness

1 PURPLE STARTER OUTPUT ( + )

Locate the vehicle starter wire.

Verification: This wire registers voltage only when the key is turned to the

START position. Cut the vehicle's starter wire in half when installing the

starter kill relay.

Verification after starter wire is cut:

KEY SIDE of starter wire registers voltage when the key is turned to the

START position.

MOTOR SIDE of starter wire registers no voltage.

Connect the PURPLE wire to the vehicle starter wire, use the MOTOR SIDE of the vehicle

starter wire when installing the starter kill relay.

2 RED BATTERY 12V ( + )

Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch.

Verification: This wire will register ( + ) voltage in all positions of the ignition

switch.

Connect the RED wire to the constant 12 Volt battery wire.

NOTE: Remove all fuses until all connections are made.

4 PINK/WHITE IGNITION 2 ( + )

Locate the vehicle’s 2nd ignition wire at the ignition switch (if equipped).

Verification: This wire registers voltage when the key is turned to the ON (or

RUN) position, but not the ACC (Accessory) position. The voltage does not

drop out when the key is turned to the START(or CRANK) position.

Connect the PINK/WHITE wire to the vehicle’s ignition 2 wire.

Programmable output: IGN, ACC, Start.

6 PINK IGNITION 1 ( + )

Locate the vehicle’s ignition wire at the ignition switch.

Verification: This wire registers voltage when the key is turned to the ON (or

RUN) position. The voltage does not drop out when the key is turned to the

START(or CRANK) position.

Connect the PINK wire to the vehicle’s Ignition wire.

This wire is also used for Ignition 1 Output.

5 RED/WHITE BATTERY 12V ( + )

Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch.

Verification: This wire will register ( + ) voltage in all positions of the ignition

switch.

Connect the RED/WHITE wire to the constant 12 Volt battery wire.

NOTE: Remove all fuses until all connections are made.

10 ca6153 revA

3 VIOLET/BLACK AUX 1

This wire provides a ( - ) 200mA output capable of driving relays. For Control of

optional accessories (i.e. Power Window/Sunroof, etc.).

To activate refer to the transmitter button configuration chart. Please refer to the

selectable options for timing.

4 RED/WHITE TRUNK RELEASE OUTPUT ( - )

Locate the vehicle’s trunk release wire at the trunk release switch.

Verification: This wire will register either positive voltage or ground when

the trunk release is activated.

This is a low current 200mA output and in configurable in option programming.

2 BLUE/BLACK START STATUS / ACTIVE OUTPUT ( - )

This wire provides a ground output when the remote start function is activated

and remains until 4 seconds after the remote start is shutdown. If this wire will

be used for multiple application's a 1 amp diode is required in-line with the stripe

facing the control module.

6 Pin Output Harness

1 BROWN/BLACK HORN OUTPUT ( - )

Locate the vehicle’s horn wire.

Verification: This wire will register at positive voltage and register

ground when the horn switch is pressed.

Connect the BROWN/BLACK wire to the vehicle’s horn wire. This is a low current

output, 200mA.

Inhaltsverzeichnis

Andere Code Alarm Autoalarmanlage Handbücher

Code Alarm

Code Alarm CATX510 Betriebsanleitung

Code Alarm

Code Alarm CA 1150 Bedienungsanleitung

Code Alarm

Code Alarm CA-150 Bedienungsanleitung

Code Alarm

Code Alarm CATX2LED Betriebsanleitung

Code Alarm

Code Alarm ca 5152 Bedienungsanleitung

Code Alarm

Code Alarm CA 680 Bedienungsanleitung

Code Alarm

Code Alarm ca1555 Bedienungsanleitung

Code Alarm

Code Alarm Elite CA6155e Bedienungsanleitung

Code Alarm

Code Alarm CA-140 Bedienungsanleitung

Code Alarm

Code Alarm PowerCode PC 7300 Bedienungsanleitung

Code Alarm

Code Alarm F50 Bedienungsanleitung

Code Alarm

Code Alarm Procomp Bedienungsanleitung

Code Alarm

Code Alarm CA1355E Bedienungsanleitung

Code Alarm

Code Alarm F10 Bedienungsanleitung

Code Alarm

Code Alarm PROFESSIONAL SERIES CA 1551 Bedienungsanleitung

Code Alarm

Code Alarm CA 210 Bedienungsanleitung

Code Alarm

Code Alarm CATX110 Betriebsanleitung

Code Alarm

Code Alarm CA611 Bedienungsanleitung

Code Alarm

Code Alarm PROFESSIONAL SERIES Bedienungsanleitung

Code Alarm

Code Alarm Vehicle Security System Bedienungsanleitung

Code Alarm

Code Alarm CA 521 Bedienungsanleitung

Code Alarm

Code Alarm 2000 Bedienungsanleitung

Code Alarm

Code Alarm CATX520 Betriebsanleitung

Code Alarm

Code Alarm CA 180 Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Ultra Start

Ultra Start 450 SERIES Bedienungsanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Excalibur

Excalibur AL-1860-EDPB Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung