Code Alarm CATX120 Betriebsanleitung

Model CATX120

Programming Guide

The keychain transmitters included with the system have

been pre-programmed at the factory, with each button pre-

assigned to control a specific function of the system.

It is important to remember that during programming, each

individual step of the procedure must be executed within 15

seconds of the previous step.

When the 15 second time limit is allowed to expire, the

system will automatically terminate the programming mode.

This is indicated by a long chirp from the siren.

Additionally, the system will store codes from up to 4

different transmitters. If a 5th transmitter is programmed to

any receiver channel, then the first transmitterprogrammed

to that channel will be erased from the system’s memory.

To program new or additional transmitters, the alarm must

be disarmed and the valet switch must be in the OFF

position:

1. Enter the vehicle, and turn the ignition key to the ON

position.

2. Press and release the valet/programming/override

switch 3 times.

3. The dash LED will flash one time, and the sounding

device will beep one time, indication the system is ready to

accept programming for transmitter 1.

4. Press and hold the Arm Icon button until the sounding

device emits a long beep, indicating the signal has been

stored into memory.

5. If you have additional transmitters (up to 4) that need to

be programmed, repeat step 4 for each transmitter.

Changing the Remote Control Battery

The 12-volt alkaline battery supplied in your remote

transmitter should last approximately one year, depending on

usage. When the battery begins to weaken, you will notice a

decrease in range, or the distance from your vehicle that

your remote transmitter will operate. Follow the instructions

below to change the remote transmitter battery.

For Customer Service and Product information Call

1-800-421-3209

1. Insert the edge of a coin into the slot at the side of the

remote control. Twist the coin to pry the remote control

halves apart.

2. Remove the old battery and replace with a new one. Be

sure to observe the (+) and (-) signs in the battery

compartment.

3. Carefully snap the case halves back together, then test

the remote control.

Model CATX120

Programming Guide

Inhaltsverzeichnis

Andere Code Alarm Autoalarmanlage Handbücher

Code Alarm

Code Alarm 420A Bedienungsanleitung

Code Alarm

Code Alarm ca6554 Bedienungsanleitung

Code Alarm

Code Alarm CATX2LED Betriebsanleitung

Code Alarm

Code Alarm CA-125 Bedienungsanleitung

Code Alarm

Code Alarm PowerCode PC 6100 Bedienungsanleitung

Code Alarm

Code Alarm CA-120 Bedienungsanleitung

Code Alarm

Code Alarm CA 210 Bedienungsanleitung

Code Alarm

Code Alarm 2000 Bedienungsanleitung

Code Alarm

Code Alarm ca 1051 Bedienungsanleitung

Code Alarm

Code Alarm CA 6551 SST Bedienungsanleitung

Code Alarm

Code Alarm CA611 Bedienungsanleitung

Code Alarm

Code Alarm Professional caSECRS Bedienungsanleitung

Code Alarm

Code Alarm SRT 5500 Bedienungsanleitung

Code Alarm

Code Alarm PRO 3500 Technische Daten

Code Alarm

Code Alarm CA-500 Bedienungsanleitung

Code Alarm

Code Alarm ca1555 Bedienungsanleitung

Code Alarm

Code Alarm Professional ca6153 Bedienungsanleitung

Code Alarm

Code Alarm ca 5152 Bedienungsanleitung

Code Alarm

Code Alarm F20 Bedienungsanleitung

Code Alarm

Code Alarm Elite CA6155e Bedienungsanleitung

Code Alarm

Code Alarm CATX110 Betriebsanleitung

Code Alarm

Code Alarm CATX130 Betriebsanleitung

Code Alarm

Code Alarm Car Alarm CA-310 Bedienungsanleitung

Code Alarm

Code Alarm CA 420A Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Ultra Start

Ultra Start 450 SERIES Bedienungsanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Excalibur

Excalibur AL-1860-EDPB Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung