CommScope AEKT Bedienungsanleitung

Part Lists

ITEM NO.

DESCRIPTION

AEKTMNT

QUANTITY

IMAGE

1 RADOME ASSEMBLY

WIND SHIELD,MIDDLE

WIND SHIELD,BOT

4 WIND SHIELD,TOP

SCREW ASSY M5 X 16,SS316

SPACER,PLASTIC,ANTI-FALL

PIPECLAMP BRACKET NO FLANGE,AEKT

MOUNTING BRACKET,AEKT

MOUNTING BRACKET

PIPECLAMP BRACKET,W/ PIN

BOLT,CARRIAGE,M12X200,STL,GALV

SCR,W/ WSHR,M6X20,SS316

NUT,HEX,M12,STL,GALV

WSHR,FLT,M12,13X24X2.5,STL,GALV

SCR,HCS,HEX,M12X40,STL,GALV

WSHR,LK,SPLT,M12,STL,GALV

MAINTENANCE WIRE

SCR,HCS,HEX,M10X40,STL,GALV

WSHR,LK,SPLT,M10,STL,GALV

NUT,HEX,M10,STL,GALV

AEKT For

S4-90M-R1-V2

Antennas

AEKT: Antenna Enclosure KiT, including EMPTY BOX and AEKTMNT.

AEKTMNT: mounting kit of AEKT for

cylindrical pipe

installations (60-115 mm pipe diameter) for heavy duty

applications.

This document explains how to install AEKT with AEKTMNT

and how to replace the wind shield with S4-90M-R2-V2.

639853 Revision B, SEP 2019

Page 1 of 4

www.commscope.com

Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.

All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 639853 B (09/19)

M6 bolt

Snap the hook

of maintenance

wire here

EMPTY BOX

13 16 14 7

Passive Antenna

16 18

151413 19 20

M10 bolt

M12 bolt

GAP

Do not hit the endcap of the passive antenna

during installation. Leave 5 mm gap between

two endcaps.

Step1 Assemble the EMPTY BOX

Step2 Mount the EMPTY BOX

assembly to the pole

AEKT EMPTY BOX installation

Store extra brackets for future use

If the brackets lost, purchase AEKTBKT

Pre-Assembly of pipe bracket

MAXIMUM TORQUE

8.0N.m (6ft.lbs)

M12

58N.m (43ft.lbs)

639853

Page 2 of 4

www.commscope.com

Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.

All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 639853 B (09/19)

These four screws

and plastic spacers

are always kept

installed on wind

shield.

13 16 14 7

Passive antenna

141613

Pre-bend cable

per cable installation

instruction. Tie the

cable here

Fix the wind shield

after jump cables

are installed

Maintenance

wire is to prevent

the wind shield

from falling while

maintaining the

antenna.

Step 5 Mount the antenna assembly on the pole

14 15 16

M12 bolt

18 19 20

M10 bolt

GAP

Step 2 Disassemble the EMPTY BOX

Instruction of replacing wind shield with S4-90M-R1-V2

Step1 Remove the EMPTY BOX assembly from the pole

Step 3 Assemble the antenna and bracket

Step 4 Assemble the antenna and radome

Do not hit the endcap of the passive antenna

during installation. Leave 5 mm gap between

two endcaps.

MAXIMUM TORQUE

4.6N.m (3ft.lbs)

8.0N.m (6ft.lbs)

M10

37N.m (27ft.lbs)

M12

58N.m (43ft.lbs)

639853

Page 3 of 4

www.commscope.com

Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.

All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 639853 B (09/19)

Lift here

SAFETY NOTICE

The installation, maintenance, or removal of an antenna

requires qualified, experienced personnel. CommScope

installation instructions are written for such installation

personnel. Antenna systems should be inspected once a

year by qualified personnel to verify proper installation,

maintenance, and condition of equipment.

CommScope disclaims any liability or responsibility for the

results of improper or unsafe installation practices.

It is recommended that transmit power be turned off

when the field installation is performed. Follow all

applicable safety precautions as shown on this page.

Do not install on a wet or windy

day or when lightning or thunder

is in the area. Do not use metal

ladder.

Do not install near power lines.

Power lines, telephone lines,

and guy wires look the same.

Assume any wire or line can

electrocute you.

Wear shoes with rubber soles and

heels. Wear protective clothing

including a long-sleeved shirt and

rubber gloves.

The female RF connectors fitted to the antenna are designed

to fit jumper cables with standard related male RF connector.

Tighten the RF connector coupling according to torque

specification in antenna label, if the RF connectors are

tightened beyond the recommend torque, the RF connection

to the antenna may be damaged.

RF Cable Connection

The AISG connector fitted to the antenna is designed to accept

any AISG compliant cable assembly, commscope recommends

hand tightening AISG mating connector only. Applied torque to

the connector shall not exceed 1.5N*m.

Remote Electrical

Tilt Connection

Lift here

Instruction of lifting points

639853

Page 4 of 4

www.commscope.com

Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.

All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 639853 B (09/19)

Andere CommScope Gehäuse Handbücher

CommScope

CommScope FDH 3000 Bedienungsanleitung

CommScope

CommScope FOWB Bedienungsanleitung

CommScope

CommScope ODF-SPLCAB-24 Bedienungsanleitung

CommScope

CommScope BUDI-M-FPS Bedienungsanleitung

CommScope

CommScope Mini-OTE 300 Tap Bedienungsanleitung

CommScope

CommScope FOSC-ACC-B-TRAY-12-RBN Bedienungsanleitung

CommScope

CommScope TENIO Bedienungsanleitung

CommScope

CommScope BUDI-2S-SP Bedienungsanleitung

CommScope

CommScope FOSC-450-BS Bedienungsanleitung

CommScope

CommScope NOVUX Compact Closure 100 Series Bedienungsanleitung

CommScope

CommScope NovuX Fiber Optic System Bedienungsanleitung

CommScope

CommScope Flex Frame Splice Cabinet Bedienungsanleitung

CommScope

CommScope FDH 3000 Bedienungsanleitung

CommScope

CommScope RFP Bedienungsanleitung

CommScope

CommScope FOSC-500-AA Bedienungsanleitung

CommScope

CommScope NOVUX CC 100 Bedienungsanleitung

CommScope

CommScope CHD Series Bedienungsanleitung

CommScope

CommScope BUDI-M Bedienungsanleitung

CommScope

CommScope MDCC Bedienungsanleitung

CommScope

CommScope Mini-OTE 200 Series Bedienungsanleitung

CommScope

CommScope OFDC-B8G Bedienungsanleitung

CommScope

CommScope FTUO Bedienungsanleitung

CommScope

CommScope FOSC-450A Bedienungsanleitung

CommScope

CommScope AMP NETCONNECT 2U Multi-Fiber Push-On Bedienungsanleitung

Beliebte Gehäuse Handbücher anderer Marken

SilentiumPC

SilentiumPC Armis AR5 Handbuch

Pulsar

Pulsar 17/TRP80/DSPR Bedienungsanleitung

Thermaltake

Thermaltake V150 TG Bedienungsanleitung

MSI

MSI MPG SEKIRA 500X Bedienungsanleitung

Antec

Antec Dark fleet DF-10 Bedienungsanleitung

Peavey

Peavey DS 1502 Bedienungsanleitung

D-Link

D-Link ShareCenter Pro DNS-1550-04 Bedienungsanleitung

Rosewill

Rosewill RX82-U(JBOD) Bedienungsanleitung

QNAP

QNAP SAS JBOD CLI 1.0 Bedienungsanleitung

GAMDIAS

GAMDIAS Talos P1 Bedienungsanleitung

Auvs

Auvs KR615 Bedienungsanleitung

Digitus

Digitus DA-71114 Bedienungsanleitung

FS FHD-FWME4 Bedienungsanleitung

JBL

JBL CS1215T Bedienungsanleitung

Pulsar

Pulsar ARAD-S4 Bedienungsanleitung

Pulsar

Pulsar AWO454 Bedienungsanleitung

NewerTech

NewerTech Voyager S3 Bedienungsanleitung

Savio

Savio ARMOR X1 Bedienungsanleitung