CommScope BUDI-M Bedienungsanleitung

BUDI-M

INSTALLATION INSTRUCTION

Building distributor

• Box

• Base tray

• Base tower

• Termination units

• Inserts for SMOUV and ANT

Accessories

Introduction

Suitable for FTTH applications where easily pre-connectorized splitters

modules can be build in. The box is designed In such a way that it is

suitable for both spliced and connectorized solutions of the riser cable.

Kit content

• Tray kit

Seals

Wrap around cable seals

Sealblock 6 x 10 mm

Cable diameter (mm) Foam (± 5 mm)

3 95

4 90

5 80

6 75

7 70

8 60

9 50

10 40

Sealblock 6 x 15 mm

Cable diameter (mm) Foam (± 5 mm)

9 125

10 115

11 105

12 95

13 85

14 70

15 60

Sealblock 3 x 20 mm

Cable diameter (mm) Foam (± 5 mm)

14 155

15 140

16 125

17 110

18 95v

19 85

20 75

Sealblock 24 x 8 mm

Cable range A 1.8 – 5 mm

B 5 – 7 mm

Sealblock rubber 1 x 18

To use in ports S6-S7 only

Cable range 3 – 8 mm

Standard seals

PG 16

PG 21

PG 29

PG 29 (PTS 24)

TC-965-IP

Rev A, Feb 2017

www.commscope.com

1.2 Different wrap-around ports are available (including brackets).

Use two guiding pins to open the ports. Secure the bottom part to the

box with the screws.

1.4 Use a hacksaw to reach the onion rings, which can be opened

with a plier to open the in-line ports (S6/S7).

1.3 Install the cable bracket depending the cable seal..

Cut out plastic part, in case of installing a cable

1.1 Install the bracket if loop storage is needed.

1 Preparation of the box

S6 S7

2.2 Install the bracket and terminate the looped cable. Take out the

loose tube(s) from the basket for further use.

1.5 Install the wrap-around rubber seal into the port.

2.1 Cable installation into the wrap around ports. Bracket can be

different depending on the port. Secure with hook and loop fastener

tape and seal with foam (see length page 1).

2 Looped cable

2.3 Store the looped tubes in the basket.

Tie wraps / cable clamps

2.4 Route the loose tubes to the base tray. Mark left and right side

of the loose tube at their position on the base tray.

2.5 1: Storage area (looped storage shaved LT)

2: Splicing to splitter modules

3: Point-to-point applications

2.6 Store the unused looped ﬁbers in the storage area.

2.7 Store the ﬁbers which will be used later.

2.8 Store the ﬁbers which will be spliced day 1 to the splitter

modules.

2.9 Store the ﬁbers which will be spliced day 1 for the point-to-

point applications.

3.4 Install the terminated drop cable in the numbered ports on the

base tray.

3.3 Wrap one layer of foam (20 mm) on the securing position if

needed. Terminate the aramid strength member by securing the cable/

pigtail onto the bracket with tie-wrap. Depending the amount of aramid

strength member, it needs to be wrapped twice around the bracket.

3.1 Install the drop cable seal and push through the drop cable.

3.2 Remove the outer jacket over a distance of 1.2 m.

3 Drop cables (point-to-point applications)

3.6 Install the cover onto the tray.

4.1 Install the splitter holder

4 Splitters

3.5 Splice the ﬁbers from the drop cable to the ﬁbers from the

looped cable. In case of SMOUV, use the insert.

Slide

Click

4.3 Route the incoming pigtails of the splitter (marked with red ﬂag)

to the base tray (area nr. 2). Remove the outer jacket from the mark over

a distance of 1.2m. Secure with foam and tie-wrap onto the base tray.

4.2 Install the splitter into the holder and route the pigtails via the

bend control.

OCM6 butt

Slide Click

OCM6 in-line

4.4 In case of splitter modules with integrated adaptors for the

incoming signal. Insert the connector of the pigtail in the adaptor of the

splitter and route the pigtail to the base tray. Remove the outer jacket

over a distance of 1.2 m and secure with foam and tie-wrap onto the

base tray.

4.5 To release the splitter module out of the splitter holder.

4.6 Splice the incoming of the splitter to the ﬁbers coming from the

looped cable. In case of SMOUV, use the insert. Store the overlength in

the tray.

4.7 Install the cover onto the tray.

Click

5 Patching trays

5.1 Install the patch tray onto the tower.

5.2 Insert the adaptor into the designated positions.

5.3 Install the drop seals and push the PICO cable through the

seals. Remove the outer jacket over a length of 1.5 m. Secure the cable

onto the bracket with foam and tie-wraps.

5.4 Install the pigtails and store the overlength in the splice area.

Mini-PICO (no connectors)

5.6 Install the foam at the position on the patch tray and secure

with 2 tie-wraps as shown on the picture.

5.5 Route the MINI PICO ﬁbers behind the tower towards the patch

tray.

5.7 Install the splice holders onto the patch tray.

5.8 Splice the MINI PICO ﬁbers to the pigtails and store the

overlength in the splice area. Check the orientation of both ﬁbers to

avoid crossings.

5.9 Install the cover onto the tray.

5.10 In case of pre-connectorized MINI PICO cable, ﬁbers are also

routed behind the tower and secured with foam and tie-wraps onto the

tray.

6.1 Route the pigtails through the bend control towards the patch

trays. Hook and loop fastener can be used to keep them bundled.

Mini-PICO (pre-conectorized)

6 Routing pigtails from the splitter

5.11 Store the overlength of the MINI PICO ﬁbers in the splice area.

6.2 Route the pigtails through the cable clips for pigtail

management. Again hook and loop fastener can be used to keep them

in a bundle.

6.3 Install the cover onto the patch tray.

Andere CommScope Gehäuse Handbücher

CommScope

CommScope BUDI-2S-SP Bedienungsanleitung

CommScope

CommScope CHD Series Bedienungsanleitung

CommScope

CommScope ODF-SPLCAB-24 Bedienungsanleitung

CommScope

CommScope BUDI-M-FPS Bedienungsanleitung

CommScope

CommScope MDCC Bedienungsanleitung

CommScope

CommScope Mini-OTE 300 Tap Bedienungsanleitung

CommScope

CommScope RFP Bedienungsanleitung

CommScope

CommScope Mini-OTE 200 Series Bedienungsanleitung

CommScope

CommScope OFDC-B8G Bedienungsanleitung

CommScope

CommScope AMP NETCONNECT 2U Multi-Fiber Push-On Bedienungsanleitung

CommScope

CommScope FOSC-500-AA Bedienungsanleitung

CommScope

CommScope NOVUX CC 100 Bedienungsanleitung

CommScope

CommScope Flex Frame Splice Cabinet Bedienungsanleitung

CommScope

CommScope FDH 3000 Bedienungsanleitung

CommScope

CommScope NOVUX Compact Closure 100 Series Bedienungsanleitung

CommScope

CommScope FOSC-450A Bedienungsanleitung

CommScope

CommScope AEKT Bedienungsanleitung

CommScope

CommScope FTUO Bedienungsanleitung

CommScope

CommScope FOSC-ACC-B-TRAY-12-RBN Bedienungsanleitung

CommScope

CommScope FOWB Bedienungsanleitung

CommScope

CommScope FOSC-450-BS Bedienungsanleitung

CommScope

CommScope NovuX Fiber Optic System Bedienungsanleitung

CommScope

CommScope TENIO Bedienungsanleitung

CommScope

CommScope FDH 3000 Bedienungsanleitung

Beliebte Gehäuse Handbücher anderer Marken

SilentiumPC

SilentiumPC Armis AR5 Handbuch

Pulsar

Pulsar 17/TRP80/DSPR Bedienungsanleitung

Thermaltake

Thermaltake V150 TG Bedienungsanleitung

MSI

MSI MPG SEKIRA 500X Bedienungsanleitung

Antec

Antec Dark fleet DF-10 Bedienungsanleitung

Peavey

Peavey DS 1502 Bedienungsanleitung

D-Link

D-Link ShareCenter Pro DNS-1550-04 Bedienungsanleitung

Rosewill

Rosewill RX82-U(JBOD) Bedienungsanleitung

QNAP

QNAP SAS JBOD CLI 1.0 Bedienungsanleitung

GAMDIAS

GAMDIAS Talos P1 Bedienungsanleitung

Auvs

Auvs KR615 Bedienungsanleitung

Digitus

Digitus DA-71114 Bedienungsanleitung

FS FHD-FWME4 Bedienungsanleitung

JBL

JBL CS1215T Bedienungsanleitung

Pulsar

Pulsar ARAD-S4 Bedienungsanleitung

Pulsar

Pulsar AWO454 Bedienungsanleitung

NewerTech

NewerTech Voyager S3 Bedienungsanleitung

Savio

Savio ARMOR X1 Bedienungsanleitung