CommScope MDCC Bedienungsanleitung

Micro Duct Cable Closure

Content

1 Product introduction

2 Cable preparation

3 Closure installation

3.1 1W cable installation

3.2 4W/7W cable installation

3.3 12W cable installation

3.4 26W cable installation

4 Micro Duct connections

5 Closing of the closure

1 Product introduction

1.1 Dimensions

Closure external dimension 370×135×50mm

Cable outer diameter

1W (1-way) cable: 7.2mm and 9.0mm

12W (12-way) cable: 23mm

26W (26-way) cable: 36mm

4W (4-way) cable: 14.8mm

7W (7-way) cable: 18mm

1.2 Kit content

4-Way kit 7-way kit

1. Closure body

2. Wedge

3. Dummy rods

4. 6-port gel block

5. 12W drop gel block

6. 6–port gel block cover

7. 12W adapter (left)

8. 12W adapter (right)

9. Tie wraps

10. Cleaning tissue

11. Continuity strap

12. Installation instruction

MDCC

I N S T A L L A T I O N I N S T R U C T I O N

1.3 Product application

Application 1

2×26 way micro duct cable in - 6x1way micro duct cable

out

Application 2

2×12 way micro duct cable in - 6x1way micro duct cable

out

Application 3

1×26 way micro duct cable in - 2x12 way micro

duct cable out

2x1 way + 1x 4 way cable in drop port

2x1 way + 1x 7 way cable in drop port

2 Cable preparation

2.1 Remove the cable sheath and cut the micro ducts for

each cable type as indicated below.

1-way

2.1.1 1-way cable 9mm

2.1.2 1-way cable 7.2mm

2.1.2.1 Remove 150mm 7.2mm jacket and as below:

2.1.2.2 Remove 50mm rib on 7.2mm jacket as below,

make sure no further damage for 7.2mm outer

jacket.

12-way cable

2.1.3 For 12W cable used in Application 2.

220mm

320mm

50mm

110mm

feeder side

drop port

feeder side

drop port

main port

4-way, 7-way and 12 way cable

2.1.4 4-way, 7-way cable and 12W cable used in

Application 3, drop port.

26-way cable

2.1.5 For 26W cable used in Application 1.

2.1.6 For 26W cable used in Application 3, divide

micro ducts into 4 sections (shown in 2.1.6) and

cut into the length.

2.1.7

2.2 Leave the 12mm centre micro duct at maximum

70mm for 26W cable in Application 3.

3 Closure installation

3.1 Push the clip and then use the screw driver to open

the closure

3.2 1W cable installation.

3.2.1 Install the 3pcs 1W cables (or dummy rods) onto

the 6-port gel block underside.

3.2.1.1 For 9.0mm tube as below:

Note: Make sure the outer jacket contacts gel port end

surface as shown.

3.2.1.2 For 7.2mm tube as blow

Note: Make sure the outer jacket exceed gel port end

surface as shown.

①

②

90mm

140mm

50mm

Lmax=70mm

150mm

50mm

320mm

220mm

50mm

110mm

Micro Duct

L=140mm

Micro Duct

L=90mm

Micro Duct

L=140mm

Micro Duct

L=90mm

3.2.2 Install the 6-port gel block assembly onto the

closure with hooking the gel block two sides as

shown.

3.2.3 Install the top 3pcs 1W cables (or dummy rods)

onto the 6-port gel block top side.

Note:

Fit the dummy rod tabs at the slots as shown.

3.2.4 Install the 6-port gel block cover. Click in as

shown

3.3 4W/7W cable installation.

3.3.1 Install the 1pc 1W cables (or dummy rods) onto

the 4-way gel block underside.

Note: Make sure the outer jacket contacts gel

port end surface as shown.

3.3.2 Install the 4W or 7W gel block assembly onto the

closure with hooking the gel block two sides as

shown.

3.3.3 Install the top 1pc 1W cables (or dummy rods)

and 4W/7W cable.

Note: For dummy rod installation, fit the dummy rod end

at the slots as shown.

3.3.4 Install the 4W gel block cover.

Note: There is no additional gel block cover for 7W cable,

it is suitable for the original gel block in closure cover.

3.4 12W cable installation

12W cable in drop cable port

3.4.1 Install the 12W drop gel block with click two

snaps.

3.4.2 Position the cable onto the closure.

Note: Always make sure the outer jacket end meets the

gel port surface.

12W cable in main cable port

3.4.3 Install the left and right 12W adapters onto the

closure.

3.4.4 Position the 12W cable onto the closure and

close the adapters.

3.5 26W cable on main cable port installation

3.5.1 Position the cable onto the closure.

Note: Make sure the outer jacket end meets the port end-

face as shown.

4 Micro Duct Connections

4.1 Install connectors from bottom side micro ducts.

4.2 Install the connectors onto the feeder cable micro

ducts.

4.3 Mark the drop cable at the connector.

4.4 Cut the micro ducts at the mark.

4.5 Connect the micro ducts with connectors.

4.6 Repeat steps 4.1-4.5 to connect all the feeder micro

ducts to drop micro ducts.

4.7 Release the left and right 12W adapters to install the

continuity strap.

Note: Make sure the PVC tape has no contact with gel

port.

4.8 Check if all cable outer jacket ends contact the port

end-face.

4.9 Close the 12W adapter and secure the 12W cable in

drop port and 26W cable by a tie wrap as shown.

Note: The tie wrap knot is located at the closure

outer surface. (refer to 4.10)

4.10 Tie wrap knot location.

5 Closing of the closure

5.1 Close the closure and check if the screws are in the

right position.

5.2 Close the wedge until a click.

5.3 Tighten the screws at closure two sides to close the

closure.

TC-2132/IP/3-09/14

CommScope (logo) and CommScope are trademarks.

Users should rely on their own judgment to evaluate the suitability of a product for a certain purpose and test each

product for its intended application. CommScope'sonly obligations are those stated in CommScope’sStandard

Terms and Conditions of Sale. CommScope expressly disclaims any implied warranty regarding the information

contained herein, including, but not limited to, the implied warranties of merchantability or fitness for a particular

purpose.

This product is covered by one or more U.S.

patents or their foreign equivalents. For patents, see

www.commscope.com/ProductPatent/ProductPatent.aspx

To obtain information on CommScope®products, visit our website at

http://www.commscope.com/SupportCenter/TechnicalSupport.aspx

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CommScope Gehäuse Handbücher

CommScope

CommScope Flex Frame Splice Cabinet Bedienungsanleitung

CommScope

CommScope TENIO Bedienungsanleitung

CommScope

CommScope RFP Bedienungsanleitung

CommScope

CommScope FOSC-ACC-B-TRAY-12-RBN Bedienungsanleitung

CommScope

CommScope ODF-SPLCAB-24 Bedienungsanleitung

CommScope

CommScope OFDC-B8G Bedienungsanleitung

CommScope

CommScope FDH 3000 Bedienungsanleitung

CommScope

CommScope BUDI-M Bedienungsanleitung

CommScope

CommScope BUDI-M-FPS Bedienungsanleitung

CommScope

CommScope NovuX Fiber Optic System Bedienungsanleitung

CommScope

CommScope Mini-OTE 300 Tap Bedienungsanleitung

CommScope

CommScope AEKT Bedienungsanleitung

CommScope

CommScope AMP NETCONNECT 2U Multi-Fiber Push-On Bedienungsanleitung

CommScope

CommScope FTUO Bedienungsanleitung

CommScope

CommScope NOVUX CC 100 Bedienungsanleitung

CommScope

CommScope FOWB Bedienungsanleitung

CommScope

CommScope FOSC-450A Bedienungsanleitung

CommScope

CommScope FOSC-500-AA Bedienungsanleitung

CommScope

CommScope FOSC-450-BS Bedienungsanleitung

CommScope

CommScope Mini-OTE 200 Series Bedienungsanleitung

CommScope

CommScope BUDI-2S-SP Bedienungsanleitung

CommScope

CommScope CHD Series Bedienungsanleitung

CommScope

CommScope NOVUX Compact Closure 100 Series Bedienungsanleitung

CommScope

CommScope FDH 3000 Bedienungsanleitung

Beliebte Gehäuse Handbücher anderer Marken

SilentiumPC

SilentiumPC Armis AR5 Handbuch

Pulsar

Pulsar 17/TRP80/DSPR Bedienungsanleitung

Thermaltake

Thermaltake V150 TG Bedienungsanleitung

MSI

MSI MPG SEKIRA 500X Bedienungsanleitung

Antec

Antec Dark fleet DF-10 Bedienungsanleitung

Peavey

Peavey DS 1502 Bedienungsanleitung

D-Link

D-Link ShareCenter Pro DNS-1550-04 Bedienungsanleitung

Rosewill

Rosewill RX82-U(JBOD) Bedienungsanleitung

QNAP

QNAP SAS JBOD CLI 1.0 Bedienungsanleitung

GAMDIAS

GAMDIAS Talos P1 Bedienungsanleitung

Auvs

Auvs KR615 Bedienungsanleitung

Digitus

Digitus DA-71114 Bedienungsanleitung

FS FHD-FWME4 Bedienungsanleitung

JBL

JBL CS1215T Bedienungsanleitung

Pulsar

Pulsar ARAD-S4 Bedienungsanleitung

Pulsar

Pulsar AWO454 Bedienungsanleitung

NewerTech

NewerTech Voyager S3 Bedienungsanleitung

Savio

Savio ARMOR X1 Bedienungsanleitung