CommScope AMP NETCONNECT MRJ21 Bedienungsanleitung

Figure 1

MRJ21 48–port straight patch panels are designed to

be mounted onto a standard 483–mm [19–in.]

Electronic Industries Alliance (EIA) rack or equipment

cabinet as shown in Figure 1. AMPTRAC patch panels

are designed for use with the

AMP NETCONNECT® AMPTRAC system. Read these

instructions thoroughly before starting installation.

AMPTRAC Retrofit Kit 1479951–1 can be installed onto

the standard patch panel to enable the patch panel to

be connected to the AMP NETCONNECT® AMPTRAC

system. Back Cable Manager Kits 1933352–[ ] must be

used to support the cable.

Reasons for reissue of this instruction sheet are

provided in Section 6, REVISION SUMMARY.

Each 10/100BASE–T patch panel contains four

MRJ21 receptacles (one per 2 6 RJ45 connector

assembly), and each 10/100/1000BASE–T patch

panel contains eight MR21 receptacles (two per 2 6

RJ45 connector assembly). The ports are identified

by numbers printed on the front and on the back of

the patch panel. Four 12–24 screws are included to

mount the patch panel to the rack. In addition,

AMPTRAC patch panels have a sensor pc board

subassembly and two HDP–22 connectors to enable

the patch panel to connect to the

AMP NETCONNECT® AMPTRAC system.

AMP NETCONNECT®

9-JAN-17 Rev E

This product is covered by one or more U.S.

patents or their foreign equivalents. For patents, see

www.commscope.com/ProductPatent/ProductPatent.aspx

To obtain information on CommScope®products, visit our website at

http://www.commscope.com/SupportCenter/TechnicalSupport.aspx

Shielded patch panels are designed to protect the

internal electronic components from electromagnetic

interference (EMI).

1. Using the screws, mount the patch panel onto

the rack. Refer to Figure 1.

2. Plug a connector (from the trunk cable) into

each MRJ21 receptacle (at the back of the patch

panel). Refer to Figure 2. Make sure to align the

keying features of the connector and receptacle.

Ensure that the connector is fully seated,

then

using a small cross–recessed tipped screwdriver,

turn the jack screws of the connector

clockwise

and tighten to a maximum torque of 0.23 Nm

[2 lbf–in.].

3. For AMPTRAC patch panels, plug the connector

of an I/O cable assembly (PN 1499507–[ ]) from

the analyzer into each HDP–22 connector (at the

back of the patch panel). See Figure 2.

4. Install the retro–fit kit onto the rack according to

Instruction Sheet 408–10170. Using cable ties or

similar fasteners, attach the cables to the tie–down

bar. It is recommended to maintain a minimum

bend radius of 50.8 mm [2 in.] when securing and

routing cables. See Figure 2.

For port–to–cable pair cross–reference, refer to

Figure 3.

Figure 2

Figure 3

Patch panels are not repairable. DO NOT use a

damaged patch panel or one with damaged or

defective connectors.

Revisions to this instruction sheet include:

Added shielded patch panels

Removed wiring distribution bracket kit, and

modified Figure 2

S Rebranded to CommScope

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CommScope Netzwerk-Hardware Handbücher

CommScope

CommScope SYSTIMAX 360 iPatch G2 MPO Bedienungsanleitung

CommScope

CommScope MRJ21 Quick Fit Cassette Bedienungsanleitung

CommScope

CommScope NOVUX SEC 100 Bedienungsanleitung

CommScope

CommScope Constellation CPT-PP-48C Bedienungsanleitung

CommScope

CommScope SYSTIMAX AirSPEED AP542 Bedienungsanleitung

CommScope

CommScope OneCell RP5000 Series Leitfaden

CommScope

CommScope CPPR-QF-F-1U-E Bedienungsanleitung

CommScope

CommScope SYSTIMAX 100BASE-T Bedienungsanleitung

CommScope

CommScope Mini-OTE 300 Bedienungsanleitung

CommScope

CommScope ONECELL RP5200 Handbuch

CommScope

CommScope FPX Series Bedienungsanleitung

CommScope

CommScope FPX Series Bedienungsanleitung

CommScope

CommScope ION-M23 SDARS Bedienungsanleitung

CommScope

CommScope RUCKUS SmartZone 300 Bedienungsanleitung

CommScope

CommScope FPX Series Bedienungsanleitung

CommScope

CommScope ION-M7P Bedienungsanleitung

CommScope

CommScope NETCONNECT 1479542-1 Bedienungsanleitung

CommScope

CommScope FOSC-OC-6 Bedienungsanleitung

CommScope

CommScope UNJ10G Bedienungsanleitung

CommScope

CommScope ION-M7P Bedienungsanleitung

CommScope

CommScope ION-U EU H 23/23 Bedienungsanleitung

CommScope

CommScope M3200 Bedienungsanleitung

CommScope

CommScope Uniprise Solutions HFTP-HD6B-1U-24 Bedienungsanleitung

CommScope

CommScope TC-96370-IP Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung