CommScope ION-M7P Bedienungsanleitung

Optical Remote Unit

ION™-M7P

(M-cabinet)

Manual

MF0143A8A

Manual for ION™-M7P

Page 2 MF0143A8A.doc

Andrew Solutions is a trademark of CommScope, Inc.

All information contained in this manual has been revised thoroughly. Yet Andrew

Solutions accepts no liability for any omissions or faults.

Andrew Solutions reserves the right to change all hard- and software characteristics

without notice.

Names of products mentioned herein are used for identification purposes only and

may be trademarks and / or registered trademarks of their respective companies.

No parts of this publication may be reproduced, stored in a retrieval system,

transmitted in any form or by any means, electronical, mechanical photocopying,

recording or otherwise, without prior written permission of the publisher.

Andrew Wireless Systems GmbH, 20-October-2011

Page 3

TABLE OF CONTENTS

1. GENERAL 7

1.1. USED ABBREVIATIONS 7

1.2. HEALTH AND SAFETY WARNINGS 8

1.3. ABOUT ANDREW SOLUTIONS 10

1.4. INTERNATIONAL CONTACT ADDRESSES FOR CUSTOMER SUPPORT 11

2. FUNCTIONAL DESCRIPTION 13

2.1. PURPOSE 13

2.2. THE ION-M7P (INTELLIGENT OPTICAL NETWORK; MMR) 13

2.3. COMPONENTS OF THE ION-M7P REMOTE UNIT 14

2.3.1. Fan-Protection Kit 14

2.3.2. Accessories 14

3. COMMISSIONING 15

3.1. MECHANICAL INSTALLATION 15

3.1.1. General 15

3.1.2. Wall-Mounting Procedure 16

3.1.3. Pole-Mounting Procedure 17

3.1.4. Mounting of Fan Protection 19

3.2. ELECTRICAL INSTALLATION 20

3.2.1. General 20

3.2.2. Connections 21

3.2.3. Grounding 22

3.3. CONNECTION OF THE ANTENNA CABLES 23

3.4. POWER CONNECTION 24

3.5. OPTICAL-FIBER-CABLE CONNECTION - RULES 25

3.5.1. Protective Plug 27

3.5.2. Protective-Tube Kit 29

3.6. COMMISSIONING 31

4. ALARMS 34

4.1. BITE AND ALARMS 34

4.2. HANDLING OF ALARMS 34

4.3. ALARM STATUS 34

Manual for ION™-M7P

Page 4 MF0143A8A.doc

4.4. STATUS LED ALARMS 35

4.5. EXTERNAL ALARM INPUTS AND OUTPUTS 36

4.6. TROUBLESHOOTING 37

5. MAINTENANCE 38

5.1. GENERAL 38

5.2. REPLACING THE FAN UNIT 39

5.3. CLEANING THE HEAT SINK 41

6. APPENDIX 42

6.1. ILLUSTRATIONS 42

6.2. SPECIFICATIONS 43

6.2.1. Electrical Specifications 43

6.2.2. Mechanical Specifications 43

6.2.3. Environmental and Safety Specifications 43

6.3. SPARE PARTS 44

7. INDEX 45

Page 5

FIGURES AND TABLES

figure 3-1 Wall mounting, (metric dimensions).......................................................... 16

figure 3-2 Pole-mounting kit...................................................................................... 17

figure 3-3 Pole mounting (metric dimensions) .......................................................... 18

figure 3-4 Mounting procedure for fan protection, (metric dimensions)..................... 19

figure 3-5 Connector flange of ION-M7P .................................................................. 21

figure 3-6 RS485 connector...................................................................................... 22

figure 3-7 Grounding bolt with loosened hex nut ...................................................... 22

figure 3-8 Grounding bolt, schematic view................................................................ 22

figure 3-9 AC mains plug.......................................................................................... 24

figure 3-10 DC mains plug........................................................................................ 24

figure 3-11 Protective-plug assembly ....................................................................... 27

figure 3-12 Tube-kit installation................................................................................. 30

figure 4-1 Flange connector, 5 poles........................................................................ 36

figure 4-2 Flange connector, 7 poles........................................................................ 36

figure 4-3 Alarm inputs and outputs, standard.......................................................... 37

figure 6-1 Installation drawing................................................................................... 42

table 1-1 List of international contact addresses....................................................... 12

table 3-1 RS485 connector, PIN assignment............................................................ 22

table 4-1 Status LED alarms..................................................................................... 35

Manual for ION™-M7P

Page 6 MF0143A8A.doc

For your notes:

1. GENERAL

1.1. USED ABBREVIATIONS

3GPP 3rd Generation Partnership Project

AC/DC Alternating current / Direct Current

AIMOS Andrew Integrated Management and Operating System

ALC Automatic Level Control

BITE Built-In Test Equipment

BTS Base Transceiver Station

CE "Conformité Européenne" ("European Conformity")

CD Compact Disk

CPD Channel Power Detection

DL Downlink

DoC Declaration of Conformity

EDGE Enhanced Data Rates for GSM Evolution

EN European Norm

EP Extension Port

ESD Electrostatic Discharge

ETS European Telecommunication Standard

EU Extension Unit

GSM Global System for Mobile Communication

GND Ground

GUI Graphical User Interface

ICP3 Intercept Point 3rd order

ID No Identification Number

ION Intelligent Optical Network

IP Ingress Protection

ISO International Organization for Standardization

LED Light Emitting Diode

LMT Local Maintenance Terminal

LTE Long Term Evolution

MIMO Multiple Input Multiple Output

MS Mobile Station

MU Main Unit

NF Noise Figure

OTRx Optical Transceiver = SRMU (Subrack Master Unit)

PG Packing Gland

PIM Passive Intermodulation

R&TTE Radio & Telecommunications Terminal Equipment

Rev Revision

RF Radio Frequency

RU Remote Unit

RX Receiver

SNMP Simple Network Management Protocol

TS Technical Specification

TX Transmitter

UL Uplink

UMTS Universal Mobile Telecommunication System

UPS Uninterruptible Power Supply

VSWR Voltage Standing Wave Ratio

WCDMA Wideband Code Division Multiple Access

WDM Wavelength Division Multiplex

1.2. HEALTH AND SAFETY WARNINGS

1. Only suitably qualified personnel is allowed to work on this unit and only after

becoming familiar with all safety notices, installation, operation and maintenance

procedures contained in this manual.

2. Read and obey all the warning labels attached to the unit. Make sure that the

warning labels are kept in a legible condition and replace any missing or

damaged labels.

3. Obey all general and regional installation and safety regulations relating to work

on high voltage installations, as well as regulations covering correct use of tools

and personal protective equipment.

4. Keep operating instructions within easy reach and make them available to all

users.

5. It is the responsibility of the network provider to implement prevention measures

to avoid health hazards which may be associated to radiation from the antenna(s)

connected to the unit.

6. Note for a Class A digital device or peripheral:

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may

cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in

which case the user will be required to correct the interference at his own

expense.

7. Make sure, access is restricted to qualified personnel.

8. Only licence holders for the respective frequency range are allowed to operate

this unit.

9. Corresponding local particularities and regulations must be observed. For national

deviations please refer to the respective documents included in the manual CD

delivered.

10.Use this equipment only for the purpose specified by the manufacturer. Do not

carry out any modifications or fit any spare parts which are not sold or

recommended by the manufacturer. This could cause fires, electric shock or other

injuries.

11.Due to power dissipation, the repeater may reach a very high temperature. Do not

operate this equipment on or close to flammable materials.

Page 8 MF0143A8A.doc

12.Before opening the unit, disconnect mains.

13.ESD precautions must be observed! Before commencing maintenance work, use

the available grounding system to connect ESD protection measures.

14.This unit complies with European standard EN60950.

15.Make sure the repeater settings are according to the intended use (see also

product information of manufacturer) and regulatory requirements are met.

16.Although the repeater is internally protected against overvoltage, it is strongly

recommended to earth the antenna cables close to the repeater’s antenna

connectors for protection against atmospheric discharge.

17.Laser radiation! Do not stare into the beam; do not view it directly or with optical

instruments.

Page 10 MF0143A8A.doc

1.3. ABOUT ANDREW SOLUTIONS

Andrew Wireless Systems GmbH based in Buchdorf/ Germany, is a leading

manufacturer of coverage equipment for mobile radio networks, specializing in high

performance, RF and optical repeaters. Our optical distributed networks and RF

repeater systems provide coverage for every application: outdoor use, indoor

installations, tunnels, subways and many more.

Andrew Wireless Systems GmbH has unparalleled experience in providing RF

coverage and capacity solution for wireless networks in both indoor and outdoor

environment and belongs to Andrew Solutions, a CommScope Company.

Andrew Solutions is the foremost supplier of one-stop, end-to-end radio frequency

(RF) solutions. Our products are complete solutions for wireless infrastructure from

top-of-the-tower base station antennas to cable systems and cabinets, RF site

solutions, signal distribution, and network optimization.

Andrew Solutions has global engineering and manufacturing facilities. In addition, it

maintains field engineering offices throughout the world.

We operate a quality management system in compliance with the requirements of

ISO 9001. All equipment is manufactured using highly reliable material. In order to

ensure constant first-rate quality of the products, comprehensive quality monitoring is

conducted at all fabrication stages. Finished products leave the factory only after a

thorough final acceptance test, accompanied by a test certificate guaranteeing

optimal operation.

Note: Exceptions of and national deviations from this intended use may be

possible. To observe corresponding local particularities and

regulations, please refer to the respective documents (also in

national language) which are included in the manual CD delivered.

To make the most of this product, we recommend you carefully read the instructions

in this manual and commission the system only according to these instructions.

For technical assistance and support, please also contact the local office or Andrew

Solutions directly at one of the addresses listed in the following chapter.

Andere Handbücher für ION-M7P

Inhaltsverzeichnis

Andere CommScope Netzwerk-Hardware Handbücher

CommScope

CommScope UNJ10G Bedienungsanleitung

CommScope

CommScope SYSTIMAX 100BASE-T Bedienungsanleitung

CommScope

CommScope NOVUX DSC 650 Bedienungsanleitung

CommScope

CommScope NOVUX SEC 100 Bedienungsanleitung

CommScope

CommScope SYSTIMAX AirSPEED AP542 Bedienungsanleitung

CommScope

CommScope ION-U EU H 7P/80-85P/17P/19P Bedienungsanleitung

CommScope

CommScope ION-U EU H 23/23 Bedienungsanleitung

CommScope

CommScope EHD Bedienungsanleitung

CommScope

CommScope SCIL-B Bedienungsanleitung

CommScope

CommScope ION-U EU H 7P/80-85P/17P/19P Bedienungsanleitung

CommScope

CommScope OneCell RP5000 Series Leitfaden

CommScope

CommScope LSX Bedienungsanleitung

CommScope

CommScope FOSC-OC-6 Bedienungsanleitung

CommScope

CommScope M3200 Bedienungsanleitung

CommScope

CommScope FPX Series Bedienungsanleitung

CommScope

CommScope Mini-OTE 300 Bedienungsanleitung

CommScope

CommScope RUCKUS SmartZone 300 Bedienungsanleitung

CommScope

CommScope SD-4U-SPLICE PANEL Bedienungsanleitung

CommScope

CommScope TC-96370-IP Bedienungsanleitung

CommScope

CommScope ST-BSP60 Bedienungsanleitung

CommScope

CommScope NG4access ODF Platform Value-Added Module Bedienungsanleitung

CommScope

CommScope RUCKUS SmartZone 100 Bedienungsanleitung

CommScope

CommScope NG4access ODF Platform Value-Added Module Bedienungsanleitung

CommScope

CommScope CPP-UDDM-SL-1U-24 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung