CommScope UNJ10G Bedienungsanleitung

Uniprise Solutions®www.commscope.com

Instruction Sheet 860508548

Issue 3, October 2013

UNJ10G Outlet Instructions

General

The Uniprise Solutions®UNJ10G outlets support Category 6a applications and are available in a variety of

colors. These products are modular RJ45 to insulation displacement connectors (IDC). They are typically

installed in faceplates at work locations and provide termination for the horizontal 4-pair cable at the IDC end,

and workstation cord insertion at the RJ45 end.

The following tools are available to aid in module termination.

Material ID Description

406477794 D-914 kit − includes impact tool and 110 blade

407484971 D-914 impact tool only

407728427 Replacement 110 blade for D-914 impact tool

760122713 Module removal tool (quantity of 5)

860333673 Hand termination tool (hand puck)

405423260 KS-22035-L2 spudger tool

How to Contact Us

•To find out more about CommScope®products, visit us on the web at http://www.commscope.com/

•For technical assistance:

- Within the United States, contact your local account representative or technical support at

1-800-344-0223. Outside the United States, contact your local account representative or

Authorized Business Partner.

- Within the United States, report any missing/damaged parts or any other issues to

CommScope Customer Claims at 1-866-539-2795. Outside the United States, contact your

local account representative or Authorized Business Partner.

For RoHS Inquiries:

CommScope Inc.

Corke Abbey, Bray

Co. Dublin, Ireland

Attn: Legal Department

Page 1 of 5

860508548

Instruction Sheet www.commscope.com

Termination Procedure

T568B Wiring Shown

Pre-Termination Step For Angled Entry

Note: Some mounting hardware and box space does not

allow for cable entry directly from the rear. If a typical

termination from the rear is done and the cable is then bent

in the needed direction, performance and reliability can

suffer. A proper termination should have the intended entry

direction set before seating the conductors.

1. Set the intended entry angle before seating the

conductors.

2. Pull pairs into the module until the jacket is snug

against the rear housing. Outer pairs should sweep

around the inside pairs and not be pulled into them.

Direct Cable End Reverse Cable End

Orange pair

Green pair Brown pair

(Blue pair)

(Brown pair) (Orange pair)

(Green pair)

Blue pair

1. Each cable end has two pairs routed into the holes and two pairs routed over the top, without crossover or

rearrangement. On the Direct cable end, the Orange and Blue pairs enter the holes and the Green and

Brown pairs lay over the top. On the Reverse cable end, the Green and Brown pairs enter the holes and the

Orange and Blue pairs lay over the top.

2. Pull pairs into the module until the jacket end is snug against the rear housing.

Cable positioned at 90

prior to seating conductors

Page 2 of 5

www.commscope.com

860508548

Issue 3, October 2013

3. To place conductors, hold the pair down on the

termination position and bend it for easy grasp as

shown above. Then untwist the pair in a counter-

clockwise direction enough to open it up.

4. Push conductors down into slot

positions (check color codes).

Maintain pair twist up to the

opening for the slots.

Orange pair

Blue pair

Green pair

Brown pair

Ensure that front pairs

are tightly routed

5. (T568B wiring shown) On the Direct cable end, place Orange and Blue pairs first, then place Green and

Brown pairs.

Page 3 of 5

860508548

Instruction Sheet www.commscope.com

Orange pair

Blue pair

Green pair

Brown pair

Ensure that front pairs

are tightly routed

6. (T568B wiring shown) On the Reverse cable end, pull Green and Brown pairs back, eliminate the twist, and

pull them tightly into place. Then route Orange and Blue pairs to the front positions.

Note: For T568A Wiring -

On each cable end, one of the two pairs fed in through the holes is pulled back for the rear positions. Check

label color codes.

Conductor Seating and Cutting

Impact tool on HI setting

with M110 cutting blade

Hand puck

Pliers

Trim pairs

flush

Fine edge

cutters

1. Use impact tool on HI setting with M110

cutting blade

to punch conductors

straight down into slots. When using the

impact tool, the hand puck is

recommended.

2. Use pliers with wire cap to seat

conductors. Use fine edge cutters to

trim conductors flush to the module

body.

Page 4 of 5

www.commscope.com

860508548

Issue 3, October 2013

Module Removal

1. To remove a module for inspection or

repair, insert prongs of removal tool into

openings at sides of module and press

firmly.

The module wiring cap can also be used to

remove a module. Insert prongs of cap into

openings at sides of module and press

firmly.

2. The module can then be removed from the

back.

Inspection or Repair of Termination

Note: To enable inspection or repair, the wiring

cap can be released from the module using the

removal tool. A spudger tool can then be used

to remove conductors for repair.

1. Insert end of removal tool into slot under

wiring cap and pivot it forward to release

cap.

Removal tool

Insert end of tool into

slot under wiring cap

Pivot removal tool forward

to disengage cap

Slot

Page 5 of 5

Inhaltsverzeichnis

Andere CommScope Netzwerk-Hardware Handbücher

CommScope

CommScope AMP NETCONNECT MRJ21 Bedienungsanleitung

CommScope

CommScope ION-M23 SDARS Bedienungsanleitung

CommScope

CommScope FPX Series Bedienungsanleitung

CommScope

CommScope SYSTIMAX AirSPEED AP542 Bedienungsanleitung

CommScope

CommScope ION-M7P Bedienungsanleitung

CommScope

CommScope FDC-W8-FAT Bedienungsanleitung

CommScope

CommScope Mini-OTE 300 Bedienungsanleitung

CommScope

CommScope SYSTIMAX EHD Bedienungsanleitung

CommScope

CommScope WCS-2 Bedienungsanleitung

CommScope

CommScope RUCKUS SmartZone 100 Bedienungsanleitung

CommScope

CommScope NETCONNECT 1479542-1 Bedienungsanleitung

CommScope

CommScope Constellation CPT-PP-48C Bedienungsanleitung

CommScope

CommScope ION-M7P Bedienungsanleitung

CommScope

CommScope FPX Series Bedienungsanleitung

CommScope

CommScope NOVUX SEC 100 Bedienungsanleitung

CommScope

CommScope SYSTIMAX 100BASE-T Bedienungsanleitung

CommScope

CommScope FPX Series Bedienungsanleitung

CommScope

CommScope OneCell RP5000 Series Leitfaden

CommScope

CommScope LSX Bedienungsanleitung

CommScope

CommScope CPPR-QF-F-1U-E Bedienungsanleitung

CommScope

CommScope TC-96370-IP Bedienungsanleitung

CommScope

CommScope SD-4U-SPLICE PANEL Bedienungsanleitung

CommScope

CommScope Uniprise Solutions HFTP-HD6B-1U-24 Bedienungsanleitung

CommScope

CommScope MRJ21 Quick Fit Cassette Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung