Craftsman 315.235360 Bedienungsanleitung

Owner's Manual

CRIIFTSMFIW

AccESSORIES FOR THE

10 in. (254 mm) COMPOUND MITER SAW

Model No.

315.235360

Item No.

_923537

(accessories optional)

_923536

(accessories included)

Save this manual for

future reference.

CAUTION: Read and

followallSafety Rulesand

Operating Instructionsbefore

firstuseofthisproduct.

•SAFETY

•LOOSE PARTS

•INSTALLATION

•SERVICES

Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

972000-485

1-98

READ ALL INSTRUCTIONS •

...... L,"

•READ THESE INSTRUCTIONS AND THE

-INS_ 315;235360 COM-

._PQI.LNDMLT.EB.._.A.__TJ:!_ROUGHLY before •

using accessories._ .:_::!_ _,

•KNOW YOUR POWER TOQL Read the owner's

m_n_r f0Pthe (3ompo-u-h_'MiterSaw carefully.

•Lear_-tht_w_ and i'mitations as •

we.!! as.thesp._otential hazards related to

this tool.

KEEP THE WORK AREA CLEAN. Cluttered

work areas and work benches invite accidents.

DO NOT leave tools or pieces of wood on the

saw while it is in operation.

ALWAYS WEAR SAFETY GLASSES. Everyday

eyeglasses have only impact-resistant lenses;

they are NOT safety glasses.

ALWAYS DISCONNECT SAW FROM POWER

SUPPLY BEFORE MAKING ADJUSTMENTS

OR ADDING ACCESSORIES. Make sure the

switch is off when reconnecting to power supply.

SAVE THESE INSTRUCTIONS. Refer to them

frequently and use to instruct other users, if you

loan someone this tool, loan them these instruc-

tions also.

_k Look for this symbol to point out important safety precautions. It

means attention!!! Your safety is involved.

The following accessories are included with item no. _23536. They are optional and may also be purchased for

use with item no. 92.3537:

•Work Clamp (item no. _'23461)

•8 mm Work Clamp Screw (Included with

Work Clamp)

• Dust Bag (Item no. 9-23466)

• Owner's Manual

•Stop Block (Included with Table Extensions)

•Table Extensions (2) (Item no. _23464)

• Large Wing Screws(2) (Included with Table

Extensions)

• Small Wing Screw (Included with Table

Extensions)

WORKCLAMP

_8mm

WORKCLAMPSCREW

LARGEWINGSCREWS

SMALLWINGSCREW

_WARNING: The use of attachments or accessories not listed might be hazardous.

Fig, 1

AWARNING: To prevent accidental starting that

could cause possible serious personal injury,

assemble all parts to your saw completely before

connecting itto power supply• Saw should never

be connected to power supply when you are

assembling parts, making adjustments, installing

or removing blades or accessodas, or when not

in use.

WORK CLAMP

See Figure 2.

The work clamp (Item no. 92.3461) provides greater

control by clamping the workpiece to the fence. It

also prevents the workpiece from creeping toward the

saw blade. This is very helpful when cutting com-

pound miters. To install the work clamp, place the

shaft of the clamp in either hole in front of the miter

table base. Thread the 8 mm work clamp screw

provided into the side of the base and tighten itto

secure the clamp in position. Rotate the knob on the

clamp to move it in or out as needed.

_IL WARNING: Make sure the saw blade or blade

guard will not hit the work clamp assembly when

cutting 35° to 45° angles. Failure to heed this

warning can result in serious personal injury.

EXHAUSTPORT

Fig. 3

TABLE EXTENSIONS

See Figure 4.

To install the table extensions (Item no. _23464),

insert the ends of the extensions intothe holes in the

sides of the base. Adjust the extensions to the desired

length. To secure them in place, screw the two large

wing screws provided intothe holes in the front ofthe

base and tighten them securely.

8 mmWORK

CLAMP

SCREW

tVORK

CLAMP

°DUST BAG

See Figure 3. -:

Fig. 2

The dust bag (Item no. 923466) fits over the exhaust

port on the upper blade guard. To install it, remove

the dust guide from the exhaust port. Then, squeeze

the two metal clips to open the mouth of the bag and

slide it on the exhaust port. Release the clips. The

metal ring in the bag should lock in between the

grooves on the exhaust port. For more efficient

operation, empty dust bag when no more than half

•_ This will permit better air flow through the bag.

STOPBLOCK

SMALL

WIN4

TABLEEXTENSION

; SCREW

Fig. 4

STOP BLOCK

See Figures 4 and 5.

The stop block is useful as a stop for cutting multiple

pieces to the same length. It can be installed on either

table extension on either side of the saw base:

•Slide the stop block on the back arm of either

table extension, then insert the table extension

into the saw base. See Figure 4.

•Use the large wing screws to secure the table

extensions to the saw base and the small wing

screw to secure the stop block to the table exten-

sion. See Figure 4.

•Loosen the small wing screw and adjust the stop

block the desired distance from the blade for the

cut to be made.

•Tighten small wing_screw securely.

•Make a test cut in scrap material and measure the

length of the workpiece.

•Make any necessary adjustments.

_1= WARNING: When using the work clamp with

the stop block, install the clamp on the stop block

side of the blade. This will eliminate the

possibility of the saw catching the loose end and

kicking up. Failure to heed this warning can

result in serious personal injury.

STOP

BLOCK

Fig. 5

Fortherepair orreplacementparts

youneeddelivereddirectlyto yourhome

Call7 am - 7 pm, 7daysaweek

1-8OO-366-PART

(1-800-366-7278)

Forrepairservice

Call24 hoursa day,7 daysaweek

1-800-4-REPAIR

_(!-800-473-7247)

SEARS

America's Repair Specialists

Forthe location of a

SearsPads andRepairCenter

inyourarea

Call24 hoursaday,7 daysaweek

1-8OO-488-1222

Whenrequestingserviceororderingparts,

alwaysprovidethe followinginformation:

•ProductName

10 inchCompound

Miter Saw

• ModelNumber

315.235360

•PartName •Part Number

Andere Handbücher für 315.235360

Dieses Handbuch passt für folgende Modelle

Andere Craftsman Zubehör Handbücher

Craftsman

Craftsman 509347 Bedienungsanleitung

Craftsman

Craftsman Floor Cabinet Bedienungsanleitung

Craftsman

Craftsman 486.24611 Bedienungsanleitung

Craftsman

Craftsman SNOW CAB 486.24276 Bedienungsanleitung

Craftsman

Craftsman 486.24599 Bedienungsanleitung

Craftsman

Craftsman 351.264271 Bedienungsanleitung

Craftsman

Craftsman 486.24275 Bedienungsanleitung

Craftsman

Craftsman 358.792443 Bedienungsanleitung

Craftsman

Craftsman Door Kit Bedienungsanleitung

Craftsman

Craftsman 486.246211 Bedienungsanleitung

Craftsman

Craftsman BACKWALL WITH METAL PEGBOARD Bedienungsanleitung

Craftsman

Craftsman 113.29931 Bedienungsanleitung

Craftsman

Craftsman 315.212400 Bedienungsanleitung

Craftsman

Craftsman 390.2519 Bedienungsanleitung

Craftsman

Craftsman 358.792450 Bedienungsanleitung

Craftsman

Craftsman 351.240870 Bedienungsanleitung

Craftsman

Craftsman 316.792410 Bedienungsanleitung

Craftsman

Craftsman 486.24100 Bedienungsanleitung

Craftsman

Craftsman 358.792442 Bedienungsanleitung

Craftsman

Craftsman 358.792401 Bedienungsanleitung

Craftsman

Craftsman 944.511591 Bedienungsanleitung

Craftsman

Craftsman FRONT BUMPER 486.245981 Bedienungsanleitung

Craftsman

Craftsman 486.24598 Bedienungsanleitung

Craftsman

Craftsman 875.59750 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung