Craftsman 486.248474 Bedienungsanleitung

Operator's Manual

CRAFr. MAN®

FRONT SCOOP TRACTOR ATTACHMENT

Model No. 486.248474

DO NOT RETURN TO STORE

For Missing Parts or Assembly

Questions Call 1-866-576-8388

CAUTION:

Before using this product, read

this manual and follow all Safety

Rules and Operating Instructions.

,, Safety

,, Assembly

,, Operation

,, Maintenance

,, Parts

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

www.sears.com/craftsman

PRINTED IN U.S.A. FORM NO. 42086 (02/02/09)

WARRANTY .................................................................... 2

SAFETY RULES .............................................................. 3

FULL SIZE HARDWARE CHART .................................... 4

CARTON CONTENTS ..................................................... 6

ASSEMBLY ...................................................................... 7

OPERATION .................................................................. 17

MAINTENANCE ............................................................ 18

TROUBLESHOOTING ................................................... 19

REPAIR PARTS ILLUSTRATION .................................. 20

REPAIR PARTS LIST ..................................................... 21

SLOPE GUIDE .............................................................. 23

PARTS ORDERING/SERVICE ......................... Back Page

ONE YEAR FULL WARRANTY

When operated and maintained according to the instructions supplied with it, if this Front Scoop Tractor Attachment fails

due to a defect in material or workmanship within one year from the date of purchase, call 1-800-4-MY-HOME® to arrange

for free repair (or replacement if repair proves impossible).

If this product is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., D817WA, Hoffman Estates, IL 60179

The model number and serial number will be found on a

decal attached to the bucket.

You should record both the serial number and the date of

purchase and keep in a safe place for future reference.

MODEL NUMBER:

SERIAL NUMBER:

DATE OF PURCHASE:

486.248474

Anypowerequipmentcancauseinjuryifoperatedimproperlyoriftheuserdoesnotunderstandhowtooperatetheequipment.

Exercisecautionatalltimeswhenusingpowerequipment.

o Readthisoperator'smanualbeforeattemptingto

assembleoroperatethescoopattachment.

o Readthevehicleowner'smanualandknowhow

tooperateyourvehiclebeforeusingthescoop

attachment.

o Nevercarrypassengersinthescoopbucket.Ithas

notbeendesignedtocarrypassengers.

o Neverallowchildrentooperatethevehicleorthe

scoopattachment.

o Donotallowadultstooperatethevehicleorscoop

attachmentwithoutproperinstructions.

o Alwaysbeginwiththetransmissioninfirst(low)and

graduallyincreasespeedasconditionspermit.

o Drivethetractoratreducedspeedoverroughterrain

andhillsidesornearcreeksandditchestoprevent

tippingoverandlossofcontrol.Donotdrivetooclose

toacreekorditch.

o Neverramthescoopintomaterialathighspeed.

o Vehiclebrakingandstabilitymaybeaffectedwith

theattachmentofthisscoop.Donotfillthescoop

tomaximumweightcapacitywithoutcheckingthe

capabilityofthevehicletosafelydriveandstopwith

thescoopattached.

o Beforeoperatingvehicleonanygrade(hill)refer

tothesafetyrulesinthevehicleowner'smanual

concerningsafeoperationonslopes.Referalsotothe

slopeguideonpage23ofthismanual.Stayoffsteep

slopes!

o Followmaintenanceandlubricationinstructionsas

outlinedinthismanual.

[_ ookforthissymboltopointoutimportantsafetyprecautions.Itmeans--Attention!! Becomealert!! Your safety is involved.

These and other accessories are recommended for use with your unit. Call 1-800-4-MY-HOME® to find out ifthey are available.

If available, they may be purchased at most Craftsman outlets or by calling 1-800-4-MY-HOME®.

WHEEL WEIGHT TIRE CHAINS

______-------

._____-------

.______------

____.____..-----

IV]

/BB

E_F

"-i3 F

PARTS NOT SHOWN FULL SIZE

[ViM

QQ RR

PARTS BAG CONTENTS

Not all parts will be needed for fit-up to any one tractor.

Discard unneeded parts after assembly is finished.

REF QTY

A 2

B 2

C 3

D 2

E 6

F 4

G 5

H 1

I 3

J 8

K 2

L 1

M 2

N 1

O 2

P 2

Q 2

R 10

S 11

T 2

U 3

V 1

DESCRIPTION

Hex Bolt, 5/8" x 1-1/2"

Hex Bolt, 1/2" x 1-3/4"

Hex Bolt, 1/2" x 1"

Hex Bolt, 3/8" x 1-1/4"

Hex Bolt, 3/8" x 1"

Hex Bolt, 5/16" x 1"

Hex Bolt, 5/16" x 1-3/4"

Hex Bolt, 5/16" x 3-1/2"

Hex Bolt, 1/4" x 1-3/4"

Carriage Bolt, 3/8" x 1"

Carriage Bolt, 5/16"x 1"

Slotted Truss Head Bolt, 10-32 x 5/8"

Nylock Nut, 5/8"

Hex Lock Nut, 1/2"

Nylock Nut, 1/2"

Nylock Jam Nut, 1/2"

Hex Nut, 3/8"

Nylock Nut, 3/8"

Nylock Nut, 5/16"

Hex Nut, 5/16"

Nylock Nut, 1/4"

Hex Nut, 1/4"

REF

QTY

DESCRIPTION

Nylock Nut, #10-32

Spacer, 5/8" Long

Spacer, 1/2" Long

Hairpin Cotter, Long

Hairpin Cotter, Short

Cotter Pin, 1/8" x 1-1/4"

Cotter Pin, 1/8" x 1-1/2"

Lock Washer, 3/8"

Washer, 5/16"

Washer, 3/8" (Small)

Washer, 1/2" (Small)

Washer, 3/8" (Large)

Washer, 5/8"

Washer, 1/2" (Large)

Washer, 3/4"

Washer, 1"

Clevis Pin

Compression Spring, Short

Compression Spring, Long

Cable Tie

Tilt Stop Bracket

Hose Clip

1. BucketAssembly

2. PinStopBracket

3. LiftFrameAssembly

4. LiftBracketAssembly

5. TiltAnchorAssembly

6. Right(Long)SidePlate

7. Left(Long)SidePlate

8. Right(Short)SidePlate

9. Left(Short)SidePlate

10.DumpControlRod

11.LiftStrapAssembly(2)

12.TiltBracketAssembly

13.AttachmentRod

14.DumpHandleTube

15.LiftHandleTube

16.DumpControlPin

17.DumpPivotBracket

18.DumpHandleTubeExtension

19.LiftHandleTubeExtension

TOOLS REQUIRED FOR ASSEMBLY

(!)

(2)

(1)

Standard Screwdriver

15/16" Wrenches (one should be box-end)

3/4" Wrenches

9/16" Wrenches

1/2" Wrenches

7/16" Wrenches

3/8" Wrench

ADDITIONAL ITEMS NEEDED

Ruler or Tape Measure

Grease

REMOVE PARTS FROM CARTON

• Remove the hardware pack and all loose parts from

the carton.

Lay cardboard on floor to help prevent scratching of

painted parts.

5/16" WASHERS (EE)

5/16"

NYLOCK

NUT(T) 3/8" x 1=1/4"

/- HEX BOLT(D)

3/8" NYLOCK NUT (R) 3/8" HEX NUT(e)

Lay out and identify all the parts and hardware as

shown on pages 4 through 6. FIGURE 1

ASSEMBLE SCOOP

STEP 1: iNSTALL TWO BOLTS

(SEE FIGURE 1)

•Assemble two 3/8" x 1-1/4" hex bolts (D) and 3/8" hex

nuts (Q), threading the nut all the way onto the bolt

until it is tight against the head of the bolt.

Install a nut/bolt assembly into the bucket assembly

and fasten using a 3/8" nylock nut (R). Tighten.

Repeat for the other side.

STEP 2: iNSTALL PiN STOP BRACKET

(SEE FIGURE 1)

•Install the pin stop bracket to the top of the bucket

assembly using four 5/16" x 1" hex bolts (F), eight

5/16" washers (EE) and four 5/16" nylock nuts (T).

Leave the bolts loose enough that the position of the

pin stop bracket can be adjusted later.

STEP 3: INSTALL LiFT FRAME ASSEMBLY

(SEE FIGURE 2)

•Apply grease to the mounting surface of the bucket

assembly and the inside of the lift frame arms.

Assemble the lift frame assembly to the bucket

assembly using two 5/8" x 1-1/2" hex bolts (A) and

5/8" nylock nuts (M). Tighten, then loosen the nuts

1/4 turn, or until the lift frame pivots freely.

5/8" x1=1/2"

HEX BOLT (A)

APPLY

GREASE /-

5/8" NYLOCK

NUTS (M)

APPLY LIFT FRAME

GREASE ASSEMBLY

-/ 5/8" x 1=1/2"

HEX BOLT (A)

APPLY GREASE

FIGURE 2

STEP4: iNSTALL LiFT BRACKET ASSEMBLY

(SEE FIGURE 3)

o Assemble the lift bracket assembly to the lift frame

assembly using two 5/8" washers (11)and 1/8" x 1-1/4"

cotter pins (BB).

!-... 5/8" WASHER ill)

LiFT BRACKET 1/8" x1=1/4"

ASSEMBLY COTTER

I'-.. ] ] (BB)

I "4 I

LiFT FRAME

ASSEMBLY

FIGURE 3

STEP 6: iNSTALL LIFT STRAP ASSEMBLIES

(SEE FIGURE 5)

• Loosen the bolts and nuts on the lift strap

assemblies 1/4 turn or until the straps will slide back

and forth.You will retighten them later in step 26.

Turn the lift strap assemblies as shown. Install each lift

strap assembly to an arm of the lift bracket assembly

and then secure with a small 1/2" washer (GG) and a

short hairpin cotter (AA).

Position the lower end of each lift strap assembly to

the outside of the lift frame. Fasten to the upper front

holes in the lift frame using a clevis pin (MM), 1/2"

long spacer (Y) and short hairpin cotter (AA) for each

assembly.

NOTE: The lift strap assemblies may be installed in the

rear mounting holes of the lift frame to increase the lift

height, but this will also increase the lifting effort. The

front holes give a lift height of about 6-1/2" and require 28

Ibs. of force to lift a 150 Ib load. The rear holes will give a

lift height of about 8-1/2" and require 35 Ibs. of force.

STEP 5: INSTALL TILT ANCHOR ASSEMBLY

(SEE FIGURE 4)

• Assemble the tilt anchor assembly to the lift bracket

assembly using two 1/2" x 1" hex bolts (C) and 1/2"

nylock jam nuts (P). Tighten.

1/2" NYLOCK

P"_ JAM NUTS(P)

TiLT ANCHOR _-__

1/2" x 1"

HEX BOLT (C) "I

I I

\ I

LiFT I 1/2" x 1"

BRACKET I HEXBOLT (C)

SHORT HAiRPiN

ARM COTTER (AA)

/1/2" WASHER

_P_@../ (SMALL) (GG)

LiFT STRAP

SHORT ASSEMBLY

HAiRPiN /-...

COTTER (AA) "'_)

112" SPACER (Y) X

UPPER FRONT CLEVIS PiN (MM)

MOUNTING HOLE

FIGURE 5Bucket removed for clarity

FIGURE 4

STEP7: iNSTALL EXTENSION SPRING

(SEE FIGURE 6)

*Lightly apply grease to the end of the arm on the tilt

anchor assembly and install the tilt bracket assembly

to the arm using a 1/2" x 1" hex bolt (C) and 1/2" hex

lock nut (N). Tighten then loosen the nut 1/4 turn, or

until the tilt bracket assembly pivots freely.

Install a 1/4" x 1-3/4" hex bolt (I) through the end of

the extension spring on the tilt bracket assembly and

then install a 1/4" hex nut (V) onto the bolt. Next,

insert the end of the bolt into the hole in the arm of

the tilt anchor assembly and install a 1/4" nylock nut

(U) onto the bolt. Tighten the nuts to secure the bolt

to the arm.

_1/4" NYLOCK NUT (U)

1/4" REX NUT(V)

"-yJj

114"x 1-314"

HEX BOLT(I) SPRING

112" x1" HEX BOLT (C)

FIGURE 6

STEP 8: iNSTALL STOP BRACKET BOLT

(SEE FIGURE 7A)

For lift straps installed in front holes

*Install the long compression spring (OO) and then the

two 5/8" spacers (X) onto the 5/16" x 3-1/2" hex bolt (H).

Insert the bolt into the stop bracket and install two 5/16"

hex nuts (T) onto the bolt. Adjust nuts later in step 29.

5116"HEX NUTS(T) j _

5/8" SPACERS(X) "_

LONG COMPRESSION

SPRING (OO)

5/16" x 3-1/2" I._

HEX BOLT(H)

FIGURE 7A

(SEE FIGURE 7B)

For lift straps installed in rear holes

*Install the long compression spring (OO) and then a 5/8"

spacer (X) onto the 5/16" x 3-1/2" hex bolt (H). Insert

the bolt into the stop bracket and install a 5/8" spacer

(X) and two 5/16" hex nuts (T) onto the bolt. Adjust nuts

later in step 29.

5116"HEX NUTS(T) /_

5/8" SPACERS(X) '_

LONG COMPRESSION

SPRING (OO)

5/16" x 3-1/2" I._

HEX BOLT(H)

FIGURE 7B

STEP 9: iNSTALL DUMP PIVOT BRACKET

(SEE FIGURE 8)

•Install a 1/8" x 1-1/2" cotter pin (CC) to the inside hole

in the shaft shown in figure 8, and then install a 1"

washer (LL) onto the shaft. Apply grease to the end of

the shaft and install the dump pivot bracket assembly

onto the shaft. Install a 1" washer (LL) onto the shaft

and secure it using a 1/8" x 1-1/2" cotter pin (CC).

1/8" x 1=1/2"

COTTER PIN (CC)

j_'_ 1" WASHERS (LL)

1/8" x 1=1/2"

COTTER PIN (CC)

DUMP PIVOT

BRACKET

FIGURE 8

STEP 11 :INSTALL TILT STOP BRACKETS

(SEE FIGURE 10)

•Install a tilt stop bracket (QQ) to each side of the

bucket using a 3/8" x 1" carriage bolt (J), a small 3/8"

washer (FF) and 3/8" nylock nut (R). Do not tighten

the nuts until step 28.

TiLT STOP

BRACKET (QQ)

3/8" NYLOCK _'_'-_

NUT(R) 3/8" x 1" j_o

3/8" WASHER (FF) CARRIAGE BOLT(J)

FIGURE 10

STEP 10: iNSTALL DUMP CONTROL ROD

(SEE FIGURE 9)

•install a 1/8" x 1=1/4" cotter pin (BB) intothe inside hole

in each end of the dump control rod. Spread the ends

of the cotter pins and wrap around the rod. Install a 5/8"

washer (11)onto each end of the control rod.

Install the dump control rod to the dump pivot bracket

and bucket. Fasten using two 5/8" washers (11)and

1/8" x 1-1/4" cotter pins (BB). Spread the ends of the

cotter pins and wrap around the rod.

1/8" x 14/4"

COTTER PiN (BB)

5/8" WASHERS (ll)

1/8" x 1=1/4"

COTTER

PINS (BB)

1/8" x 14/4"

COTTER PiN (BB)

5/8" WASHERS (ll)

DUMP

CONTROL

ROD

FIGURE 9

STEP 12: INSTALL LiFT HANDLETUBE

(SEE FIGURE 11)

•Install the lift handle tube into the index bracket using

two 5/16" x 1-3/4" hex bolts (G) and 5/16" nylock nuts

(s).

5/16" NYLOCK

NUTS (S) _\®_

LiFT HANDLE

TUBE

5/16" × 1=3/4"

HEX BOLT (G)

iNDEX

BRACKET

FIGURE 11

Andere Craftsman Rasen- und Gartengeräte Handbücher

Craftsman

Craftsman 917.248950 Bedienungsanleitung

Craftsman

Craftsman 486.24536 Bedienungsanleitung

Craftsman

Craftsman 650 Series Bedienungsanleitung

Craftsman

Craftsman POWER RAKE 486.2928 Bedienungsanleitung

Craftsman

Craftsman 917.248951 Bedienungsanleitung

Craftsman

Craftsman 358.795630 Bedienungsanleitung

Craftsman

Craftsman CMXGZBF7124336 Bedienungsanleitung

Craftsman

Craftsman 486.248463 Bedienungsanleitung

Craftsman

Craftsman 486.242411 Bedienungsanleitung

Craftsman

Craftsman 358.796355 Bedienungsanleitung

Craftsman

Craftsman Incredi-Pull 316.725860 Bedienungsanleitung

Craftsman

Craftsman 486.244120 Bedienungsanleitung

Craftsman

Craftsman 486.244021 Bedienungsanleitung

Craftsman

Craftsman 3One 917.257562 Bedienungsanleitung

Craftsman

Craftsman 610.24600 Bedienungsanleitung

Craftsman

Craftsman 486.243291 Bedienungsanleitung

Craftsman

Craftsman 757.242330 Bedienungsanleitung

Craftsman

Craftsman 842.242560 Bedienungsanleitung

Craftsman

Craftsman 917.248930 Bedienungsanleitung

Craftsman

Craftsman 486.24504 Bedienungsanleitung

Craftsman

Craftsman 944.361065 Bedienungsanleitung

Craftsman

Craftsman 358.795620 Bedienungsanleitung

Craftsman

Craftsman 610.24489 Bedienungsanleitung

Craftsman

Craftsman 358.796370 Bedienungsanleitung

Beliebte Rasen- und Gartengeräte Handbücher anderer Marken

Vertex

Vertex 1/3 HP Technische Daten

GHE

GHE AeroFlo 80 Bedienungsanleitung

Millcreek

Millcreek 406 Bedienungsanleitung

Land Pride

Land Pride Post Hole Diggers HD25 Bedienungsanleitung

Yazoo/Kees

Yazoo/Kees Z9 Commercial Collection System Z9A Programmierhandbuch

Premier designs

Premier designs WindGarden 26829 Bedienungsanleitung

Snapper

Snapper 1691351 Bedienungsanleitung

Mosquito Magnet

Mosquito Magnet Patriot Bedienungsanleitung

Perfect

Perfect BG2 Bedienungsanleitung

P.Lindberg

P.Lindberg LS2 Bedienungsanleitung

Gardena

Gardena Easy 1887 Bedienungsanleitung

Makita

Makita UM104D Bedienungsanleitung

AQUA FLOW

AQUA FLOW PNRAD Bedienungsanleitung

Tru-Turf

Tru-Turf RB48-11A Golf Green Roller Benutzerhandbuch

BIOGROD

BIOGROD 730710 Bedienungsanleitung

Land Pride

Land Pride RCF2784 Bedienungsanleitung

Makita

Makita UM110D Bedienungsanleitung

BOERBOEL

BOERBOEL Standard Floating Bar Gravity Latch Bedienungsanleitung