Craftsman 2723303 836.27233 Bedienungsanleitung

2723303

Owner's Manual

ELECTRIC NAILER

Model No.

836.272330

Serial No.

NOTE: Model and serial numbers may be found on the name plate

located on the tool.

You should record both numbers and retain them in a safe place.

CAUTION: Before using this Nailer, read this manual and follow all

its Safety Rules and Operating instructions.

E185030 Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

SECTION PAGE

Warranty ................................................... 2

Product Specifications ........................................ 2

Safety Instructions ........................................... 3

Accessories and Attachments .................................. 6

Know Your Brad Nailer ........................................ 7

Operation .................................................. 7

Maintenance ................................................ 8

Troubleshooting Guide ........................................ 9

Parts ..................................................... 10

FULL ONE YEAR WARRANTY ON CRAFTSMAN PROFESSIONAL

ELECTRIC NAILER

Ifthis Craftsman Nailer fails due to a defect in material or workmanship within

one year from the date of purchase, Sears will REPAIR it, free of charge.

WARRANTY SERVICE IS AVAILABLE BY SIMPLY RETURNING THE

TOOLTOTHE NEAREST SEARS STORE OR CRAFTSMAN OUTLET IN

THE UNITED STATES.

This warranty gives you specific legal rights, and you may also have other

rights which vary from state to state.

Seam, Roebuck and Co., Dept. 817 WA, Hoffman Estates,/L 60179

Power Source

Nailing Speed

Nail Size - Diameter

- Head size

- Length

Magazine Capacity

Dimensions

Weight

120V, 60Hz, 9 Amps., AC only

1Nail per Second

.039 o .049 inch

.070 o.087 inch -

3/8 - 1-3/16 inch

100 Nails

8-1/2 inches long x 2-1/2 inches wide x 10 inches high

4.7 pounds

To avoid electrical hazards, fire hazards, or damage to the tool, use proper

circuit protection.

Your nailer is wired at the factory for 120V operation. Connect to a 120V, 15 amp

branch circuit and use a 15 amp time delay fuse or circuit breaker. To avoid shock

or fire, replace power cord immediately if it is worn, cut or damaged in any way.

Page 2

GENERAL SAFETY

INSTRUCTIONS 6. DON'T FORCETHETOOL. It will do

the job better and safer if used at

the rate for which itwas designed.

Do not attempt to operate this tool until 7.

you have read and thoroughly

understand all instructions, safety

rules, etc., contained in this manual.

Failure to comply can result in accidents

involving fire, electric shock, or serious

personal injury. Save this owner's 8.

manual and review it frequently for

continuing safe operation and instructing

possible third-party users.

READ ALL INSTRUCTIONS

1. KEEP WORK AREA CLEAN.

Cluttered work areas and benches

invite injuries.

2. GUARD AGAINST ELECTRICAL

SHOCK. Be sure your body does

not come in contact with grounded

surfaces such as pipes, radiators,

ranges, refrigerators, etc.

3. AVOID DANGEROUSWORK AREA

ENVIRONMENT. Do not use power

tools in damp or wet locations. Keep

work area well lit. Do not expose

power tools to rain, Do not use

power tools in the presence of

flammable liquids or gases.

4. KEEP CHILDREN AWAY. All visitors

should wear safety goggles or safety

glasses with side shields and be

kept a safe distance from work area.

Do not let visitors come in contact

with tool or extension cords.

5. STORE IDLE TOOLS. When not in

use, store tools in a high, dry

location that can be locked.

KEEP THEM OUT OF THE REACH

OF CHILDREN.

USETHE RIGHTTOOL Do not use

atool for a purpose it was not

intended. For example, do not force

asmall tool or attachment to do the

job of a heavy-duty tool.

ALWAYS WEAR SAFETY GOGGLES

or safety glasses with side shields

when using power tools. Also use

a face mask or dust mask if the job

is dusty.

g. DON'T ABUSE TOOL POWER

CORD. Never carry the tool by the

cord or yank the cord to disconnect

it from the wail. Keep the cord away

from heat, oil, and sharp edges.

10.SECURE WORK. Whenever

possible, use clamps or a vise to

hold the work. It's safer than using

your hands and it frees both hands

to use _,_=_u,.

11. DON'T OVERREACH. Keep proper

footing and balance; make sure

your footing is stable.

12. KEEP TOOL WELL MAINTAINED.

Follow instructions for lubricating

and changing accessories. When

applicable, keep tool sharp and

clean. Inspect cord frequently and

have damaged parts repaired by a

Searsservice center. Keep tool

handle and housing clean, dry and

free of grease and oil. Never use

strong solvents or petroleum-based

products to clean tool.

SAVE THESE INSTRUCTIONS

Page 3

13.DISCONNECTTOOL when not in

use, before servicing and when

loading or changing accessories.

14.AVOID UNINTENTIONAL

STARTING. Never carry tool with

your finger on the switch.

15.STAY ALERT, Watch what you are

doing and use common sense. Do

not operate tool when you are tired

or under the influence of drugs,

alcohol, or medication.

16.CHECK DA;w;AGED PARTS. Before

using tool, check that all parts will

operate correctly and will perform as

designed. Any damaged parts

should be repaired or replaced by

an authorized Sears service facility.

Also, check for misalignment,

binding, and broken parts. Check

that the switch works properly and

DO NOT USETOOL IFTHE

SWITCH DOES NOTTURN THE

TOOL ON AND OFF.

17. REPLACEMENT PARTS, When

servicing, use only identical

replacement parts ordered from a

Sears service facility.

18.WEAR HEARING PROTECTION

during extended periods of

operation.

GUIDELINES FOR

EXTENSION CORDS

If you are using an extension cord

outdoors, be sure itis marked with the

suffix "vV-A" ("_/" in Canada) to indicate

that it is acceptable for outdoor use.

Be sure your extension cord is

properly wired, and in good electrical

condition. Always replace adamaged

extension cord or have it repaired by a

qualified person before using it.

Protect your extension cords from

sharp objects, excessive heat and

damp or wet areas.

(when using 120 volts only)

Ampere Rating

more than not more than

0 6

6 10

10 12

Totallengthofcordln feet

25' 50' 100' 150'

18 16 16 14

18 16 14 12

16 16 14 12

WEAR YOUR

ALWAYS WEAR EYE PROTECTION. Any Power Tool

can throw foreign objects into4he eyes which could

cause permanent eye damage. ALWAYS wear safety

Goggles (not glasses) that comply with ANSI safety

standard Z87.!. Everyday glasses have only

impact-resistant lenses...they ARE NOT safety glasses.

Safety Goggles are available at Sears.

NOTE: Glasses or goggles not in compliance with

ANSI Z87.1 could seriously hurt you when they break.

SAVE THESE INSTRUCTIONS

Page 4

SPECIFIC SAFETY INSTRUCTIONS

FOR THIS NAILER

DO NOT AIM NAILER OR SHOOT

NAILS AT A PERSON OR ANIMAL.

Released nails can cause severe injuries.

1. USE ONLYTHE NAILS INDICATED

in this manual. Use of accessories

that are not designed for this tool

could result in personal injuryand/or

damage to the tool.

2. DO NOT TOUCH metal parts of tool

during operation. Hold only plastic

handle or housing.

3. KEEP tacking speed at one nail

per second.

4. NAILER should be used only for

the purposes outlined in this manual.

It is designed for use on wood,

Do not use on hard surfaces like

rock, concrete, etc. personal injury

or damage to the tool could result.

5. When nailing thin wood, special

caution must be taken for

possible penetration of nails

through the wood.

6. When using this tool in high

locations, ,_LWAYS make sure there

is no one below that could be

injured. ALWAYS be sure you have

a firm footing when using this tool.

7. ALWAYS hold tool firmly.

8. NEVER connect tool to a DC

power source.

9. REGULAR CLEANING, inspection

and maintenance is necessary.

10.DURING OPERATION, the nailer

may feel warm to the touch. This is

normal. However, if the nailer starts

to feel hot, discontinue use until the

unit cools down,

GROUNDING INSTRUCTIONS

IN THE EVENT OF A MALFUNCTION

OR BREAKDOWN, grounding provides

apath of least resistance for electric

current to reduce the risk of electric

shock. This tool is equipped with an

electric cord having an equipment

grounding conductor and a grounding

plug. The plug must be plugged into a

matching outlet that is properly installed

and grounded in accordance with all

local codes and ordinances.

DO NOT MODIFY THE 3-PRONG

PLUG. If it will not fit the outlet, have the

proper outlet installed by a qualified

electrician. Improper connection of the

equipment-grounding conductor can

create a risk of shock. The conductor

with insulation having an outer surface

that is green (sometimes, but not always

with yellow stripes) is the equipment

grounding conductor.

REPAIR OR REPLACE DAMAGED OR

WORN CORD IMMEDIATELY, if repair

or replacement of the electric cord or

plug is ever necessary. DO NOT connect

the equipment-grounding conductor to

a live terminal,

SAVE THESE INSTRUCTIONS

Page 5

Figure A

g Plug

Grounding Prong

Properly Grounded

3-Prong Outlet

FIGURE (A) Shows a 3-wire electrical

plug and outlet that has a grounding

conductor. If a properly grounded outlet

is not available, an adapter (FIGURE B)

can be used to temporarily connect

this plug to a 2-contact ungrounded

outlet. The adapter (FIGURE B) has a

rigid lug extending from it that MUST

be connected to a permanent earth

ground, such as a properly grounded

outlet box. The Canadian Electrical

Code prohibits the use of adapters.

USE ONLY 3-WIRE EXTENSION

CORDS THAT HAVE 3-PRONG

GROUNDING PLUGS AND 3-POLE

RECEPTACLES THAT ACCEPT THE

TOOL'S PLUG.

Figure B

Grounding Lug

__ ake Sure This

is Connected to a

Known Ground

2-Prong

Receptacle

If you have any doubts as to whether

the tool is properly grounded or if the

grounding instructions are unclear,

check with a qualified electrician or

service technician.When using a

grounded tool around other ungrounded

devices, be sure that the ungrounded

devices are in good condition. An

ungrounded device can function, yet

have internal electrical problems that

could cause a hazard when brought in

contact with a grounded tool.

THE ADAPTER SHOULD ONLY BE USED

until a properly grounded outlet can

be installed by a qualified electrician.

AVAILABLE ACCESSORIES '

Visit your Sears Hardware Department

or see the Craftsman Power and

Handtcol Catalog for the fol_ov,ing

brad nails:

Sears Stock No. Lem

In_;h mm,

27218 3/8 10

27216 3/4 20

27215 1 25

27214 1-3/16 30

These brad nails can be used for:

Cabinet making

Interior decorations

Wood furniture building/repair

Display assembly

Picture frames

Door & window trim

NOTE: Use only brad nails

recommended for this nailer. Using

other sizes may be dangerous.

Sears may recommend other

accessories not listed in this manual.

Do not use accessories unless you

have completely read the instruction

manual for that accessory.

Do not attempt to modify this tool or

create accessories not recommended

for use with this tool. Any such

alteration or modification is misuse

and could result in a hazardous

condition leading to possible serious

personal injury.

Page 6

Housing cap --

Housing

Safety lock pin

Trigger switch

g mouth

cord

Latch

Nail magazine

HOW TO LOAD YOUR BRAD

NAILER (FIGURE 1)

1. Unplug nailer from power source.

2. Use only brad nails recommended;

see brad nail chart.

3. Push up the latch (1) toward the

magazine and slide out the

magazine (2).

4. Position the nailer exposing the

magazine chamber (3).

5. Load nails into the magazine, nail

points facing down toward the bottom

of the nailer.

6. When loading different lengths,

do not load nail heads into the

upper part of the slot.

Load se that the nail points are at

the bottom of the magazine (4).

7. Close magazine (2), making sure that

the nails stay seated in the track.

8. Make sure that the latch (1) is

securely locked.

Fig. 1

/_ To avoid personal injury, keep fingers

Proper loading off the trigger until ready to drive nail.

Do not point the nailer at anyone when

the nails are loaded.

4 3 Page 7

TO NAIL (FIGURE 2)

Always wear safety goggles or safety

glasses with side shields when

operating your nailer. Failure to do so

could result in objects being thrown

into your eyes, resulting in possible

serious injury.

1. Plug nailer into 120 Volt, 60Hz

power outlet,

2. Hold nailer firmly with the tacking

mouth (1) flat to the workpiece.

Do not allow familiarity of your nailer to

make you careless. Remember that a

careless fraction of a second is sufficient

to inflict severe injury.

Fig. 2 4

Use enough downward pressure to _/3. depress the safety lock pin (2).

NOTE: The safety lock pin must be _,,,_ _'f-_

depressed for this nailer to operate. _ _ \ _ !

This nailer will not fire uniess this f/_ / /'_--._ "'-)1

is done. _._;_ /// k_ J

4. Squeeze the trigger (3) to drive the _ k.'_......__ 1

brad nail. L___ I

5. If the workpiece is very hard, press _ _'_" /J

down on the housing cap (4) with _ _'_ I/

your free hand. _._

NOTE: AVOID BLANK SHOTS to

prevent wear and damage to 2

internal parts. 1 J

The nailer must be disconnected from

the electrical power source during

maintenance.

STANDARD MAINTENANCE

1. Inspect all screws and tighten

if necessary.

2. Use a clean cloth to remove dirt

from the tool.

3. Do not use gasoline, brake fluid, oils,

or solvents to clean plastic parts.

These chemicals will damage,

weaken, or destroy plastics.

4. Do not oil or grease any parts,

5. Keep the nail magazine chamber

clean.

6. Do not rotate or remove housing

cap.

Do not alter, redesign parts on this

nailer, or attach special fixturing. This

can be a source of personal injury.

Page 8

CLEARING A JAMMED NAIL

(FIGURE 3)

1. Unplug the cord and remove all

brads from the magazine.

2. Remove the two screws and

washers (1) located on the tacking

mouth cover.

3. Remove the cover (2).

CAUTION: Be careful, the safety

lock pin and spring may shoot forward.

7. Replace all parts in reverse order.

8. Tighten screws.

9. Make sure that the safety lock pin is

correctly sticking out of the tacking

mouth assembly.

Fig. 3

4. Remove safety lock pin (3) and

spring (4).

NOTE: Safety lock pin (3) has a 4_.

keyed slot on the pin which is seated 3_

in the opening on the cover (2).

5. Remove the slot cover (5).

6. Remove the jammed nail. j/ _'_t_ 5

PROBLEM PROBABLE CAUSE REMEDY

Nailer will net fire 1. Not plugged in 1, Plug in

2. Circuit breaker tripped 2. Reset circuit breaker

or fuse

3. Damaged cord 3. Have replaced by Sears

Service Center

Nail jammed 1. Dirty, rusty, or 1. Replace with new nails

deformed nails

2. Incorrect nails 2, Use recommended nail

style and size

Power loss 1. Damaged coil spring 1.Have repaired by Sears

Service Center

Page 9

ELECTRIC BRAD NAILER MODEL NUMBER 836,27233

Order by PART NUMBER, not by key number

Key Number Part Number Description

1 DCA0060030 Slot-cover (B)

2 DCAO050080 Slot-cover (A)

3 BMSO040010 Screw

4 DCA0790070 Safety cover

5 BMDO010000 Washer

6 DHBO040010 Housing screw

7 BMS0040361 Screw

8 BMS0040210 Screw

9 DHA0190010 Safety spring

10 DAA0320060 Safety lock pin (Guide bar)

1t 2723301 Screwdriver

12 2723302 Carry case

13 2723303 Owner's manual

14 2723304 Hex Key

Page 10

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Craftsman Nagelpistole Handbücher

Craftsman

Craftsman CMP21PL Bedienungsanleitung

Craftsman

Craftsman 351.184200 Bedienungsanleitung

Craftsman

Craftsman 351.153000 Bedienungsanleitung

Craftsman

Craftsman 351.182010 Bedienungsanleitung

Craftsman

Craftsman 351.184240 Bedienungsanleitung

Craftsman

Craftsman 18178 - Full Head Framing Nailer Bedienungsanleitung

Craftsman

Craftsman 142.18803 Bedienungsanleitung

Craftsman

Craftsman 351.181790 Bedienungsanleitung

Craftsman

Craftsman 351.181750 Bedienungsanleitung

Craftsman

Craftsman CMPPN23 Bedienungsanleitung

Craftsman

Craftsman 900.684253 Bedienungsanleitung

Craftsman

Craftsman CMPBN18 Bedienungsanleitung

Craftsman

Craftsman 315.115122 Bedienungsanleitung

Craftsman

Craftsman 142.18882 Bedienungsanleitung

Craftsman

Craftsman 351.184540 Bedienungsanleitung

Craftsman

Craftsman 351.181770 Bedienungsanleitung

Craftsman

Craftsman 142.18839 Bedienungsanleitung

Craftsman

Craftsman 351.181810 Bedienungsanleitung

Craftsman

Craftsman 351.183200 Bedienungsanleitung

Craftsman

Craftsman CMCN623 Bedienungsanleitung

Craftsman

Craftsman 351.182140 Bedienungsanleitung

Craftsman

Craftsman 315.115120 Bedienungsanleitung

Craftsman

Craftsman 315.114010 Bedienungsanleitung

Craftsman

Craftsman 351.181720 Bedienungsanleitung

Beliebte Nagelpistole Handbücher anderer Marken

Performance Tool

Performance Tool M643 Bedienungsanleitung

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco Fusion Technology F-35XP Bedienungsanleitung

Grizzly

Grizzly G1847 Bedienungsanleitung

Ryobi

Ryobi R18N18G Bedienungsanleitung

Black & Decker

Black & Decker 492848-00 Bedienungsanleitung

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Bedienungsanleitung

Metabo HPT

Metabo HPT NR 3690DC Bedienungsanleitung

Surtek

Surtek CN650 Abmessungen und Installationsanleitung

Makita

Makita GF600 Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco AirFree 25 Bedienungsanleitung

Freeman

Freeman P50LSLW Bedienungsanleitung

Aicon PRO

Aicon PRO DAC4507 Bedienungsanleitung

Makita

Makita AN923 Bedienungsanleitung

Grizzly

Grizzly T20644 Bedienungsanleitung

Black & Decker

Black & Decker 90514937 Bedienungsanleitung