Craftsman 351.183230 Bedienungsanleitung

SWARS

OWNER'S

MANUAL

Model No,

351.183230

Caution:

Read and follow

all safety rules and

operating instructions

before first use of this

product.

[RRFTSHRN

18 Gauge Brad Nailer

•Safety Instructions

•,Operation

•Maintenance

• Troubleshooting

• Parts List

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Part No. 9021.00 December 1995

DESCRIPTION

The SearsCraftsman18Gauge BradNailerdrivesbradsl'rom

V."to 2" long, Die cast aluminum textured finish body reduces

operator fatique. Large capacity, side loading magazine with

positive, quick action latch makes loading easy. Contact safe-

ty disables nailer unless nosepiece is in contact with work-

piece. Tapered nosepiece provides operator with greater visi-

bility for precise brad placement. Rigid nosepiece reduces

jamming. The gears 18 Gauge Brad Nailer is excellent for

molding and decorative trim, furniture making and picture

framing.

SAFETY INSTRUCTIONS

• Air tool operators and all others in work area should always

wear safety goggles (must comply with ANSI Z87.1) to

prevent eye injury from fasteners and flying debris when

loading, Ol_rating or unloading this tool.

• Never exceed operating pressure of 100 PSI (7,1 kg/em').

•Always keep hands and body away from the fastener dis-

charge area when air supply is connected to tool.

• Always disconnect tool from air supply when servicing or

adjusting tool end when tool is not in use,

• Do not operate tool when nose is not in contact with work.

• Never load the tool until you are ready to use it.

• Never depress tool trigger when loading.

•Always load tool with nose pointing away from you and

others.

• Never point tool at yourself or others,

• Never carry tool with trigger depressed.

• Do not use oxygen, combustible gas or high pressure com-

pressed gas as the air supply for the tool.

•Always use tool at safe distance from other people in work

area.,

• Do not attempt to discharge tkstener into hard or brittle

materials such as concrete, steel or tile.

• Do not connect female quick-disconnect ctmpiing to tool

side of air line.

• Connect male, free-flow nipple to tool side of air line so

that tool is depressurized when diSconnected from hose,

• Do not use ahose swivel with this tool.

• Use Sears recommended fasteners only.

SPECIFICATIONS

Capacity ............................. 100 brad nails

Brad nail size .................. 18 gauge (.049 x .040")

Brad nail Icnglhs ............................ ¼ to 2"

Operating pressure ....................... 60-100 PSI

Air inlet ............................... V,"F.N.P.T.

Length ...................................... 9'/,"

lleight ...................................... 9'/,."

Width ....................................... 2_,_"

Weight ................................... 3.5 Ibs.

Brad Nails

_]8341 ................... 18 gauge brad nails, V," hn_g

_18342 ................... 18 gauge brad nails, l" long

t] 8343 .................. 18 gauge brad nails, 1'A"long

918360 .................. ] 8 gauge brad nails. 1'/_"long

918361 .................. 18 gauge brad nails, 1)/," hmg

t18362 .................... 18 gauge brad nails 2" long

OPE" RATING INSTRUCTIONS

Air Supply Line

Refer to Figure 1.

• The Sears brad nailer operates on compressed air at pres-

sures fi'om 60 to 100 PSI.

• Never exceed maximulla pressure.

Minimum air requirements for nailer: Average working

SCFM 3.2 at 90 Pal.

WARNING; KEEP HANDS AND BODY AWAY FROM

DISCHARGE AREA OF TOOL WlIEN

CONNECTING AIR SUPPLY. ALWAYS

DISCONNECT TOOL FROM AIR SUPPLY

WHEN SERVICING OR ADJUSTING

TOOL AND WHEN TOOL IS Nor IN USE.

-.. a

Figure 1-Air _upply Line

• Clean dry air is essential to the operation of the Sears nation

*Air operated tools require clean, dry, lubricated com-

pressed air to ensure top performance, low maintenance

and long life.

•Dirt and abrasive materials presem in all air lines will dam-

age tool O-rings, valves and cylinders.

• Moisture will reduce tool performance and life if not

removed from compressed air,

•Afilter-regulator-lubricator system is required and should

be located as close to tool as possible (see Figure l). A dis-

lance of less than 15 feet is recommended

• Keep air filter clean. Adirty filter will reduce the air pres-

Nnlo: For best results use Sears nails only,

• Depress latch (Key No, 59) and slide magazine cover (Key

No. 52) backwards (see Figure 2). Insert brad nails into

magazine. Position brads at bottom of magazine with brad

head towards top of tool.

• Slide cover forward over magazine until latch snaps into

place, locking magazine cover.

Note: It may be necessary to depress latch handle to close

magazine cover.

Nailing Operation

WARNING: NEVER OPERATE TOOL UNLESS CON-

sure to the nailer causing areduction in power and effi-

ciency.

• The air supply _atem must be able to provide air pressure

of 60 to 100 pounds per square inch at tool.

• The lubricator should be filled with a non-detergent air tool

oil.

• All hoses and pipes in the air supply system must be clean

TACT "/'RIP IS IN CONTACT WITtl

WORKPIECE. DO NOT OPERATE TOOL

WITHOUT NAILS OR DAMAGE TO

TOOL MAY RESULT. NEVER FIRE NAILS

INTO THE AIR BECAUSE NAILS MAY

INJURE OPERATOR OR OTHERS AND

DAMAGE TO TOOL MAY RESULT.

and free of all moisture and foreign panicles.

• Never connect afemale quick disconnect coupling to the

tool side of air system. A male, free-flow coupling should

be connected to the tooi side of air system.

The female coupling provides a seal preventing loss of

compressed air from compressor tank when disconnected

from male coupling. If connected to tool side of air supply,

the female coupling could seal a compressed air charge in

the nailer which could discharge if the tool trigger is actu-

ated.

• The Sears 18 Gauge Brad Nailer is equipped with a contact

trip safety mechanism (see Figure 3) that disables nailer

unless contact trip is pushed against work. Hold tool han-

dle firmly and press nose of tool on workpiece where nail

is to be applied. Pull trigger to drive hall into workpiece.

•The nailer can also be operated by holding trigger

depressed and pushh_g contact trip against workpiec¢. This

operating procedure provides rapid-fire nail driving. Never

operate tool unless contact trip is in contact with work-

piece.

•The air pressure should be properly regulated.

•Different work'piece materials and different nail lengths

wiU require different operating pressure.

Refer to Figures 2 & 5 (pages 3 and 6).

WARNING: DISCONNECT TOOL FROM AIR SUPPLY.

ALWAYS LOAD WITH NOSE POINTING

AWAY FROM YOU AND OTHERS.

ALWAYS WEAR SAFETY GOGGLES

THAT COMPLY WITH ANSI Z87.1.

Figure 2-Loading Brad Nails Figure 3-Contact Trip Operation

Operating Instructions (continued)

Quick Release Nose

Refer to Figure 5 (page 6).

The Sears 18 Cruage Brad Nailer is equipped with a quick

release nose for clearing jammed nails.

* Ira nail jams in the tool, disconnect the air supply from the

too!. Open the magazine and remove any nails. Pull the

nose cover latch (Key No. 37) down and release the nose

cover. Remove the jammed nail and secure the latch,

Reload the nails and connect the air supply.

Operating Pressure

• Use only enough air pressure to perform the nailing opera-

tion. Air pressure in excess of that which is required will

make the nailing operation inefficient and may cause pre-

mature wear or damage to the tool.

.. Determine minimum air pressure required by driving some

re,stnails into the workpiece. Set air pressure so that test

nails heads are driven down flush with the work. Nails dri-

ven too deep may damage workpiece.

Exhaust Deflector

Refer to Figures 4 & 5 (pages 4and 6).

*The position of the exhaust deflector can be changed to

direct exhaust as desired. Exhaust deflector can be posi-

tioned at the left, front or right side of lOOt. Reposition

deflector (Key No. 6) by carefully removing four bolts

(Key No. 4) and rotating deflector to desired position.

• Be sure not to _nlsplace valve spring (Key No. 7). Secure

four bolts making sure that valve spring and exhaust plate

are properly positioned.

Figure 4-Exhaust Deflector Adjustment

MAINTENANCE

Lubrication

Refer to Figure 5(page 6),

Lubricate tool daily with quality air tool oil. If no air hoe lubri-

cator is used, pour five to six drops of oil into air inlet (Key

No, 3) of nailer eyeD,day.

•Keep magazine and nose clean and free of any dirt, lint or

abrasive particles,

The tip of the ram (Key No. 17) can become dented or round-

ed over time.

•Square of]"the tip of the ram with a clean, fine hand. file to

extend the life of the ram arid nailer, Nail firing will be

more consistent if the ram tip is kept clean and square.

Safety Mechanslm

Inspect oontact trip safizty mechanism daily for proper opera.

tion. Do not operate nailer if mechanism is not operating prop-

erly.

PcrJorm the following procedures to test safety mechanism:

• I,eave trigger untouched while pushing contact trip into

workpiece. Nailer must not fire.

• Pull nailer trigger while contact trip is clear of work and

pointed away fi'om operator ,_nd others. Nailer must not

fire.

• Depress anti hold trigger. Push contact trip against work

where nail is needed. The nailer should drive only one nail

each time the contact tril_ is pushed against workpicce,

If contact trip mechanism does no! operate properly,

repair nailer immediately threugh Sears Service Center.

Replace any damaged or missing pans. Use the parts list to

order parts,

Piston/Ram Assembly

Refer to Figure 5 (page 6).

Tip of' the ram (Key No. 17) can be dented or rounded over

time. Square off tip of ram with a €lcan, fine hand file to

extend the life of ram and nailer. Nail firing will be more con-

sistent if the ram tip is kept clean and square,

Rebuild Kits

Rebuild kits are available as spare parts, see page 7. Tools

should be rebuilt if tool fails to operate properly after extend-

ed use. See troubleshooting to _.etermine required replacement

parts.

Disconnect toni from air supply before attempting repair

or adJuslment.

NOTE: Be sure tool is oiled properly. Clean and oil O-rings

during reassembly.

TROUBLESHOOTING

Symptom

Triggercap leaksair

Triggerleaksair

Cap leaksair

Nose leaks air

Tool will not operate

Tool operates slowly

or loses power

Toolskipsnailsor

inconsistentoperation

Possible C=use(=)

O-ringdamaged

Damaged sealandre O-rings

1. Cap bolts loose

2. Damaged O-ring and gasket

1, Nose bolts loose

2. Damaged cylinder O-ring

3. Damaged Bumper

1, Insufficient air supply

2. Insufficient lubrication

3. Damaged or worn head valve O-rings

4, Broken head valve spring

5. Head valve binding

1, Insufficient lubrication

2. Head valve spring doesn't work

3, Damaged or worn O-rings

4. Damaged trigger assembly

5, Build-up on ram

6. Cylinder not sealed on bumper

7. Head valve poorly lubricated

8, Insufficient air supply

1'. Worn or damaged bumper

2. Build-up on ram or nose

3, Insufficient air supply

4. Damaged or worn piston O-ring

5. Insufficient lubrication

6. Damaged magazine springs

7. Magazine-nose bolts loose

8. Nails too short

9. Damaged nails

10. Incorrect nail size

11. Head valve O-rings leak

12. Damaged seal and O-rings

13. Bent or damaged ram

14. Dirty magazine

15. Damagedorworn magazine

Corrective Action

Check and replace damaged O-ring (Key No.29)

Check and replacedamagedseal and O-rings

(KeyNos. 24, 28, and 29)

t. Tighten bolts (t ay No. 4)

2. Check and replace damaged O-ring and gasket

(Key Nos. 10 and 11)

1. Tighten nose bolts (Key No, 40)

2, Check and replace damaged O-ring (Key No, 19)

3. Check and replace damaged bumper

•(Key No. 22)

1. Check air supply

2, Place five or six drops of air tool oil into inlet cap

(Key No. 3)

3. Replace damaged or worn O-rings

(Key Nos. 12 and 14)

4. Replace broken spring (Key No. 7)

5. Clean and lubricate valve and cap

(Key Nos. 9 and 13)

1. Place five or six drops of air tool oil into inlet cap

2, Check and replace spring (Key No. 7)

3. Check and replace damaged or worn O-rings

4. Check and replace trigger assembly

5. Clean and lubricate piston/ram assembly

(Key No, 17)

6. Disassemble cylinder and assemble properly

7. Disassemble head valve (Key No. 13), clean and

lubricate. Assemble properly

8. Check air supply

1. Check and replace bumper (Key No. 22)

2, Clean and lubricate piston/ram assembly

(Key No. 17) and inside of nose cover (Key No. 38)

3. Check air supply

4. Check and replace O-ring (Key No. 16)

5. Place five or six drops of air tool oil into Inlet cap

(Kay No. 3)

6. Check and replace springs (Key No. 48)

7. Tighten bolts (Key No, 40)

8. Use Sears recommended nails only

9, Discard damaged nails. Use Sears recommended

nails only.

10. Use Sears recommended nails only

11, Check and replace damaged O-rings

(Key Nos. 12 and 14)

12. Check and replace damaged seal and O-rings

(Key Nos. 24, 28 and 29)

13. Check end replace damaged piston/ram assembly

(Key No. 17)

14. Clean magazine and lubricate with air tool oil

15. Check and replace magazine (Key No. 49)

Rim 5-Rq)lacemem Forts For Brad Nailer

Replacement Parts List

KEY PART

NO. NO. DESCRIPTION QTY.

1 9006.00 Body 1

2 9007.00 Inlet cap O-ring f

3 9008.00 Inlet cap 1

4 5264.00 5-0.8 x 25mm Socket head bolt 4

5 STD852005 5ram Lock washer 6

69009.00 Deflector 1

7 6047.00 Spring 1

8 6048.00 Seal 1

9 9010.00 Cap 1

10 6050,00 13.8 x 2.4ram O.,dng 1

11 9011.00 Gasket 1

12 ' 6052.00 31.8 x 2.4mm O-ring 1

13 6053.00 Head valve 1

14 6054.00 23 x 3.5mm O-ring 1

15 6055.00 Deflector _y[inder 1

16 6056.00 21.7 x 2.9ram O-ring 1

17 90t2.00 Piston-ram assembly 1

18 9013.00 Cylinder 1

19 9014,00 29.2 x 3.5mm O-ring 1

20 9015.Q0 Spacer 1

21 901"6.00 43 x 2.4mmO-ring I

22 9017.00 Bumper 1

123 6061.00 Ram guide 1

_6065.00 Plasticseal 1

9018.00 Trigger valve head 1

26 9019.00 Spring 1

27 9020.00 Plunger 1

28 6167.00 2.5 x 1.5mm O-ring 2

29 8069.00 13 x 2mm O-ring 1

30 9022,00 Trigger cap 1

31 6074.00 Trigger lever 1

KEY PART

NO. NO. DESCRIPTION QTY.

32 6072.00 Trigger 1

33 6075.00 2.5 x 16mm Spring pin 2

34 6073.00 Clevis pin 1

35 46-221434-9 3CMI-3 E-ring 2

36 6079.00 4-7.0 x 16ram Socket head boll 1

37 9023,00 Nose cover latch 1

38 9024.00 Nose cover 1

39 9025.00 Nose plate 1

40 ' 6097.00 4-.70 x 14ram Socket head bolt 4

41 9026.00 Contact trip 1

42 9027.00 Spring 1

43 6164.00 3 x 25ram SDring pin 2

44 9028.00 Bracket 1

45 9029.00 Nose 1

46 9030.00 Pusher bracket lj

47 9031.00 Pusher 2

!48 6092.00 Pusher spring 2

49 9032.00 _Magazine 1

_50 6093.00 !Wear plate 1

51 9033.00 2.5 x 12mm Spring pin 2

52 9034.0()' Magazine cover 1

53 9035.00 Latch plate 1

54 6076.00 4-0.7 x 12mm Socket head boll 2

55 STD852004 4ram Lock washer 2

56 6080.00 4mm-,70mm Fiber hex nut 1

57 9036,00 'Latch Bracket 1

58 6084.00 Latch spring 1

59 6083.00 Latch 1

60 5809.00 4-.70 x 6ram Socket head bolt 2

61 6045.00 5-0,8 x 20mm Socket head boll 2

62 6987.00 Clevis pin 1

•9021.00 Owner's Manual 1

* Standard hardware item available locally

• Not Shown

RECOMMENDED ACCESSORIES

• 18 Gauge Brad Nai!s, %"Long 918341

• 18 Gauge Brad Nails, 1" Long 918342

•18 Gauge Brad Nails, 11,_"Long 918343

•118 Gauge Brad Nails, 1V="Long 918360

• 18 Gauge Brad Nails, 1=/4"Long _18361

•18 Gauge Brad Nails, 2"Long 918362

REBUILD KITS

• Trigger Rebuild Kit 1

Key Nos.24, 25. 27, 29, and

2ea, 28

9037.00

9038.00

9039.00

;9040.00

Head Valve Rebuild Kit 1

Key Nos,8, 10, 11, 12, and 14

Piston Ram Assembly Rebuild Kil 1

Key No. 16, 17, 22, and 23

Cylinder Rebuild Kit 1

Key Nos. 19 and 2I

SWARS

OWNER'S

MANUAL

Model No.

351,183230

When requesting service

or ordering parts, always

Iprovide the following

information:

• Product Type

•Model Number

• Part Number

•Part Description

CRRFTSMRN

18 Gauge Brad Nailer

For the repair or replacement parts you need

Call 7am - 7 pro, 7 days a week

1-800-366-PART

(1-800-366-7278)

For the location of a

Sears Repair Service Canter In your area

Call 24 hours a day, 7 days a week

1-800-488-1222 B=llliBm

SEARS

America's ReD_ir _oeciallsts

Full One Year Warranty On Craftsman Air-Drive Tools

If this Craftsman air-drive tool falls to give complete satisfaction within one full year from

the date of purchase, RETURN IT TO THE NEAREST SEARS SERVICE CENTER/DEPARTMENT IN

THE UNITED STATES, and Sears will repair It free of charge.

If this air-drive tool is used for commercial purposes, this warranty applies for

only 90 days from the date of purchase.

This warranty gives you specific legal rights and you may also have other rights which

vary from state to state,

Sears, Roebuck and Co., Dept. D/817 WA, Hoffman Estates, IL 60179

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Part No, 9021.00 December 1995

Inhaltsverzeichnis

Andere Craftsman Nagelpistole Handbücher

Craftsman

Craftsman 315.FS2000 Bedienungsanleitung

Craftsman

Craftsman 142.18894 Bedienungsanleitung

Craftsman

Craftsman 351.181770 Bedienungsanleitung

Craftsman

Craftsman 351.181730 Bedienungsanleitung

Craftsman

Craftsman 900.684253 Bedienungsanleitung

Craftsman

Craftsman 351.182010 Bedienungsanleitung

Craftsman

Craftsman 315.114010 Bedienungsanleitung

Craftsman

Craftsman 351.183200 Bedienungsanleitung

Craftsman

Craftsman CMCN616 Bedienungsanleitung

Craftsman

Craftsman 2723303 836.27233 Bedienungsanleitung

Craftsman

Craftsman 351.184420 Bedienungsanleitung

Craftsman

Craftsman 315.115120 Bedienungsanleitung

Craftsman

Craftsman 351.184490 Bedienungsanleitung

Craftsman

Craftsman 351.181750 Bedienungsanleitung

Craftsman

Craftsman 351.182140 Bedienungsanleitung

Craftsman

Craftsman 351.184090 Bedienungsanleitung

Craftsman

Craftsman CMPPN23 Bedienungsanleitung

Craftsman

Craftsman CMCN621PL Bedienungsanleitung

Craftsman

Craftsman C583-930360 Bedienungsanleitung

Craftsman

Craftsman CMP21PL Bedienungsanleitung

Craftsman

Craftsman CMCN618 Bedienungsanleitung

Craftsman

Craftsman 351.181790 Bedienungsanleitung

Craftsman

Craftsman 351.184300 Bedienungsanleitung

Craftsman

Craftsman 351.181740 Bedienungsanleitung

Beliebte Nagelpistole Handbücher anderer Marken

Performance Tool

Performance Tool M643 Bedienungsanleitung

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco Fusion Technology F-35XP Bedienungsanleitung

Grizzly

Grizzly G1847 Bedienungsanleitung

Ryobi

Ryobi R18N18G Bedienungsanleitung

Black & Decker

Black & Decker 492848-00 Bedienungsanleitung

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Bedienungsanleitung

Metabo HPT

Metabo HPT NR 3690DC Bedienungsanleitung

Surtek

Surtek CN650 Abmessungen und Installationsanleitung

Makita

Makita GF600 Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco AirFree 25 Bedienungsanleitung

Freeman

Freeman P50LSLW Bedienungsanleitung

Aicon PRO

Aicon PRO DAC4507 Bedienungsanleitung

DAJ

DAJ XR150A Bedienungsanleitung

Makita

Makita AN923 Bedienungsanleitung

Grizzly

Grizzly T20644 Bedienungsanleitung