Crestron CP2 Bedienungsanleitung

This document was prepared and written by the Technical Documentation department at:

Crestron Electronics, Inc.

15 Volvo Drive

Rockleigh, NJ 07647

1-888-CRESTRON

Crestron CP2/CP2E 2-Series Integrated Control Processor

Contents

2-Series Integrated Control Processor: CP2/CP2E 1

Introduction ...............................................................................................................................1

Features and Functions................................................................................................1

Specifications ..............................................................................................................2

Physical Description....................................................................................................3

Memory .......................................................................................................................7

Industry Compliance ...................................................................................................9

Setup/Installation .......................................................................................................................9

Rack Mounting ............................................................................................................ 9

Bussing Strip Installation ..........................................................................................10

Network Wiring.........................................................................................................11

Hardware Hookup ..................................................................................................... 12

Optional Power Supply..............................................................................................13

Programming the CP2 and CP2E.............................................................................................13

CP2/CP2E Device Library Symbols..........................................................................13

Converting Programs and Modules Created for other Systems................................. 18

Establishing Communication with the CP2/CP2E.....................................................20

Troubleshooting Communications ............................................................................22

Compiling and Uploading a Program to the Control System ....................................24

Uploading Web pages to the CP2E ...........................................................................25

Uploading Touchpanel Projects via the CP2/CP2E...................................................26

Updating the Operating System................................................................................. 26

Advanced Console Commands..................................................................................27

Troubleshooting....................................................................................................................... 28

Passthrough Mode .....................................................................................................29

Further Inquiries ......................................................................................................................31

Future Updates......................................................................................................................... 31

Software License Agreement................................................................................................... 32

Return and Warranty Policies .................................................................................................. 34

Merchandise Returns / Repair Service ...................................................................... 34

CRESTRON Limited Warranty.................................................................................34

Operations Guide - DOC. 5980 Contents •i

Crestron CP2/CP2E 2-Series Integrated Control Processor

2-Series Integrated Control

Processor: CP2/CP2E

Introduction

Features and Functions

Crestron’s CP2 and CP2E 2-Series Integrated Control Processors, cost-competitive

options in Crestron's 2-Series line of integrated control systems, are designed for

smaller home and commercial network systems. Like all Crestron control processors,

the CP2 and CP2E units house the control system software program and provide

connectivity for communication and control of all devices on the network. The CP2E

is functionally identical to the CP2, with the exception that it also provides LAN and

Web access through its built-in 10/100 BaseT Ethernet port, which supports

dynamic/static IP addressing and full-duplex TCP/IP and UDP/IP protocols.

With speed, power, and massive memory, the 2-Series control systems are ideal for

enhanced applications like media help desks, videoconferencing, distance learning,

and entertainment facilities.

Functional Summary

•

• 36 MB of Internal Memory

• 8 IR/Serial Ports

• 8 Isolated Relay Ports

• 8 I/O Versiports

• 3 RS-232/422/485 Ports

• 1 RS-232 Computer Port

• 1 Cresnet Port

• Supports SIMPL™Windows®& SIMPL+™

• Built-In 10/100 BaseT Ethernet Port (CP2E only)

• Built-In Web Server (CP2E only)

As with all of Crestron’s 2-Series control processors, the 2-Series Control Engine is

a solutions-driven control technology that is at the very heart of the CP2 and CP2E

products. The breakthrough 2-Series Control Engine is based on the 257 MIPS, 32-

Operations Guide - DOC. 5980 2-Series Integrated Control Processor: CP2/CP2E•1

2-Series Integrated Control Processor Crestron CP2/CP2E

bit Motorola ColdFireprocessor. The 2-Series operating system is vastly upgraded

from Crestron’s X-generation products, yet compatible with existing Crestron

software and programming. A key feature is the new Crestron Compiler, which

allows any existing Crestron SIMPL™ Windowscontrol program to be easily

recompiled for the 2-Series. The real-time, preemptive multi-tasking/multi-threaded

operating system offers a file system that supports long file names. The enhanced

SIMPL+™ instruction set is also fully compatible with existing Crestron SIMPL

Windows and SIMPL+ programs.

Specifications

Specifications for the CP2 and CP2E are given in the following table.

CP2/CP2E 2-Series Integrated Control System Specifications

SPECIFICATION DETAILS

CPU 32-Bit Motorola ColdFire®Processor

Processor Speed 257 MIPS (Dhrystone 2.1 Benchmark)

Memory 36MB (4MB flash, 32MB DRAM, 256KB NVRAM)*

Ports/Connectors**

NET

COMPUTER

INFRARED – SERIAL OUTPUT

I/O

RELAY OUTPUT

LAN (CP2E only)

COM (A, B, & C)

24VDC

Reset Buttons

HWR

SWR

1 – Cresnet 4-wire interface (Expandable via Cresnet

Poll Accelerator)

1 – DB9F PC interface

8 – Simultaneous one-way IR or serial output

8 – Programmable digital/analog inputs & digital outputs

8 – Normally open, isolated relays (MOV suppression)

1 – RJ45 10/100 BaseT Ethernet port

3 – DB9 bidirectional serial ports (RS-232, -422, -485),

all Cresnet Poll Accelerator ready

1 – Male receptacle for optional external power pack.

Initiates system hardware reset

System restart with or without program

Power Requirements 24 VDC, 1A, 24W (Power supply not included)***

Network Power Fuse Rating Internal self-resetting fuse****

Environmental Temperature &

Humidity

41° to 113°F (5° to 45°C)

10% to 90% RH (non-condensing)

Dimensions & Weight Height: 1.7 in (4.32 cm)

Width: 19.0 in (48.26 cm) – with ears

17.03 in (43.24 cm) – without ears

Depth: 6.64 in (16.87 cm)

Weight: 3.54 lb (1.59 kg)

* For more information on system memory usage, see Memory on page 7.

** For more information on controls, ports, and indicators, see Physical Description on page 3.

*** For information on optional power source, see Optional Power Supply on page 13.

**** Heat-sensitive device—resets within approximately 30 seconds after overload condition is

removed.

2 •2-Series Integrated Control Processor: CP2/CP2E Operations Guide - DOC. 5980

Crestron CP2/CP2E 2-Series Integrated Control Processor

Physical Description

The CP2/CP2E integrated control systems are housed in black enclosures with

labeling on the front and rear panels. The front panels of both units include standard

LEDs and two reset buttons. All connections to the units are made through their rear

panels. The front panels of the CP2 and CP2E are shown below.

Front and Rear Panels

The front panels of the CP2 and CP2E are shown below.

CP2/CP2E Front Panels

The rear panels of the units are shown below. Both units contain a single RS-232

computer port, a network connector, three COM ports, eight one-way IR/serial ports,

eight I/O ports, eight relay ports, and a 24VDC male receptacle for power supplied

through an AC power pack (purchased separately). The CP2E also contains a single

Ethernet port.

CP2/CP2E Rear Panels

Rubber feet are supplied and can be attached to the base of the unit for stability and

to prevent slippage in shelf placement and stacking configurations. The unit may also

be rack mounted by attaching the supplied metal flanges (ears).

Operations Guide - DOC. 5980 2-Series Integrated Control Processor: CP2/CP2E•3

2-Series Integrated Control Processor Crestron CP2/CP2E

Controls and Indicators

The CP2/CP2E front panel indicators and controls are described below.

PWR (Power)

This LED illuminates when the unit is connected to and receives 24VDC power from

an AC power pack or the Cresnet NET connector.

NET

This LED illuminates when the central processing unit is processing or

communicating with Cresnet devices (i.e., button pressed at Cresnet panel or data

received from Cresnet panel).

ERR

This LED illuminates when an error condition is detected. This may be the result of

hardware or software failure, or a programming error. To determine the actual error

condition, examine the message available through the Viewport menu Functions/2-

Series/errorlog.

LNK (LAN) – (CP2E only)

This LED illuminates when there is a connection to the rear panel LAN port.

ACT (LAN) – (CP2E only)

This LED illuminates when there is communication (activity) at the rear panel LAN

port.

HWR

Pressing this button initiates system hardware reset. (Same effect as disconnecting

and reconnecting power.)

SWR

Pressing this button in combination with the HWR button performs a system restart

without loading the program (refer to Troubleshooting Communications on page 22).

Pressing it alone while the system is running restarts the program.

Ports

The CP2/CP2E rear panel ports are illustrated and described below.

COMPUTER

This DB9F connector is used when programming the units with a PC. The port is

modem compatible. The modem and/or PC program cable are not included.

NET

G Z Y 24

24VDC 24W

NET

4 •2-Series Integrated Control Processor: CP2/CP2E Operations Guide - DOC. 5980

Crestron CP2/CP2E 2-Series Integrated Control Processor

NOTE: The orientation of this connector is “upside down” compared to other

Crestron network devices (e.g., CNX-BIPAD8, CNX-RMCLV). Be sure the mating

Cresnet cable connector is properly aligned before attempting to insert it, to avoid

damage to the CP2/CP2E unit.

This connector (typical Crestron network port labeled G Z Y 24) is used for

expansion to Cresnet and SmarTouch peripherals. This connector can also serve as a

24W power source to the network when CP2/CP2E unit power is supplied through

the 24VDC power supply connector by an optional AC power pack (purchased

separately); otherwise, power to the unit is supplied through this connector. There is

a 24W maximum load rating for power output. Refer to “Network Wiring” on page

11 for details.

COM (A – C)

COM C

COM B

COM A

These three DB9 (male) software programmable, bi-directional serial ports are

available for RS-232, RS-422, or RS-485 communication, with hardware and

software handshaking. Speeds are rated up to 115,200 bps. All three ports are

Cresnet Accelerator ready. The Cresnet Poll Accelerator effectively increases the

network speed, fan-out, and device addresses by a factor of 8 for each Poll

Accelerator added to the system.

NOTE: The pinout of each 9-pin port is non-standard (refer to the table after these

notes, titled "Non-Standard COM Pinout"); it contains RS-422 pins in addition to

RS-232. This may result in a conflict with some equipment and therefore all nine

pins should not be used. Only the required pins for each communication type should

be connected. For RS-232 and –422, pins 2, 3, 5, 7, and 8 are wired straight through.

NOTE: Data Set Ready (DSR) and Data Terminal Ready (DTR) are not supported.

NOTE: To support RS-485, tie pin 1 (RXD-) to pin 9 (TXD-) and pin 4 (TXD+) to

pin 6 (RXD+) in the cable (refer to the table after this note, titled "COM Pinout to

RS-485 Bus".

Non-Standard COM Pinout

PIN DIRECTION DESCRIPTION

1* To CP2/CP2E (RXD-) RS-422 Receive Data (Idles low)

2 To CP2/CP2E (RXD) RS-232 Received Data

3 From CP2/CP2E (TXD) RS-232 Transmitted Data

4 From CP2/CP2E (TXD+) RS-422 Transmit Data (Idles high)

5 RS-232 and RS-422 Signal Common

6 To CP2/CP2E (RXD+) RS-422 Receive Data (Idles high)

7 From CP2/CP2E (RTS) RS-232 Request to Send

8 To CP2/CP2E (CTS) RS-232 Clear to Send

9 From CP2/CP2E (TXD-) RS-422 Transmit Data (Idles low)

Where: *= RS-422 transmit and receive are balanced signals requiring two lines plus a ground in each

direction. RXD+ and TXD+ should idle high (going low at start of data transmission). RXD-

and TXD- should idle low (going high at start of data transmission). If necessary, RXD+/RXD-

and TXD+/TXD- may be swapped to maintain correct signal levels.

Operations Guide - DOC. 5980 2-Series Integrated Control Processor: CP2/CP2E•5

2-Series Integrated Control Processor Crestron CP2/CP2E

COM Pinout to RS-485 Bus

COM (DB9) CONNECTOR RS-485 BUS

Tie Pins 1 & 9 -

Tie Pins 4 & 6 +

Pin 5 G

INFRARED – SERIAL OUTPUT

A B C D

E F G H

S G S G S G S G

INFRARED - SERIAL OUTPUT

S G S G S G S G

These connectors provide eight serial outputs for IR or serial interface. Each output

is labeled S (signal) and G (ground). Infrared output is rated up to 1.2 MHz, at data

rates up to 115K. Serial protocols include one-way RS-232.

NOTE: Transmission levels on the infrared – serial output connectors are in the 0 to

+5VDC range, which may not be compatible with all RS-232 devices.

I/O

1 2 3 4 5 6 7 8 G

I/O

This connector provides eight software programmable analog and digital inputs as

well as digital outputs. Digital outputs offer 250mA sync from maximum 24 VDC;

catch diodes for use with "real world" loads. Digital inputs are rated 0 – 24 VDC,

20K ohms input impedance, logic threshold 1.25 VDC. Analog inputs are rated 0 –

10 VDC, protected to 24 VDC maximum, 20K ohms input impedance; pin-

programmable 2K ohms pullup resistor to +5V.

NOTE: Digital outputs are TTL values and may not work with devices requiring a

“dry” contact closure (e.g., low voltage motor controllers).

RELAY OUTPUT

OUTPUT

1 2 3 4 5 6 7 8

RELAY

These connectors provide eight normally open, isolated relay contact groups. Each

relay contact closure is rated 1A, 30 VAC/DC; MOV arc suppression is provided

across contacts for use with "real world" loads.

6 •2-Series Integrated Control Processor: CP2/CP2E Operations Guide - DOC. 5980

Andere Handbücher für CP2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Crestron Computerhardware Handbücher

Crestron

Crestron C2COM-2 Anleitung zur Verwendung

Crestron

Crestron CNXVTC-3 Bedienungsanleitung

Crestron

Crestron CNXMIDI Bedienungsanleitung

Crestron

Crestron DVPHD Bedienungsanleitung

Crestron

Crestron CNXIO-16 Bedienungsanleitung

Crestron

Crestron CNXCPU Anleitung zur Verwendung

Crestron

Crestron CNXRY-8 Bedienungsanleitung

Crestron

Crestron 3 Series Bedienungsanleitung

Crestron

Crestron DIN Rail Control Processor DIN-AP2 Anleitung zur Verwendung

Crestron

Crestron CNXIR-8 Bedienungsanleitung

Crestron

Crestron CNXCOM-2 Bedienungsanleitung

Crestron

Crestron C2VEQ-4 Anleitung zur Verwendung

Crestron

Crestron C2VEQ-4 Bedienungsanleitung

Crestron

Crestron C2ENET-1 Anleitung zur Verwendung

Crestron

Crestron DIN-AP3 Original Betriebsanleitung

Crestron

Crestron Four-Way Coupler SRD-CPL-4 Bedienungsanleitung

Crestron

Crestron CNX-PAD8 Bedienungsanleitung

Crestron

Crestron TPS-GA-TPI Bedienungsanleitung

Crestron

Crestron DSP-860 Maßzeichnung

Crestron

Crestron UPX-2 Bedienungsanleitung

Crestron

Crestron CNXAO-8 Bedienungsanleitung

Crestron

Crestron ST-CP Bedienungsanleitung

Crestron

Crestron DigitalMedia DMC-VID4 Bedienungsanleitung

Crestron

Crestron UPX-OS4GB-MSO-2007 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung