Crestron IRP2 Bedienungsanleitung
Crestron IRP2
Infrared Emitter
Installation Guide
This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
All brand names, product names and trademarks are the property of their respective owners.
©2004 Crestron Electronics, Inc.
Crestron IRP2 Infrared Emitter
Contents
Infrared Emitter: IRP2 1
Introduction..............................................................1
Description.......................................................1
Package Contents .............................................2
Installation................................................................2
Attach the IRP2 to the IR Sensor Window ......2
IR Mask Installation.........................................3
Attach the IRP2 to Other Locations.................3
Connect the IRP2 .............................................4
Further Inquiries.......................................................5
Future Updates .........................................................6
Return and Warranty Policies ..................................7
Merchandise Returns / Repair Service.............7
CRESTRON Limited Warranty.......................7
Installation Guide - DOC. 8168A Contents •i
Crestron IRP2 Infrared Emitter
Infrared Emitter: IRP2
Introduction
The IRP2 is an infrared emitter housed in a plastic shell. The IRP2 shell
emits IR control signals sent to it by a Crestron®control system. The IRP2
shell can be installed directly on the IR sensor window of the controlled
device or at a nearby suitable location. The IRP2 is compatible with
2-Series controllers. It is also compatible with X-Generation controllers
by exchanging the 3.5 mm connector for a 5 mm connector (not supplied).
It is not compatible with the CNMS generation.
Description
The IRP2, shown below, contains an infrared (IR) LED housed in a
miniature, mouse shaped, black, injection molded plastic shell. The IRP2
has a ten-foot (304.8 cm) lead terminated in a two-pin 3.5 mm connector.
Installation Guide - DOC. 8168A Infrared Emitter •1
Infrared Emitter Crestron IRP2
Package Contents
In addition to the IRP2, this package also contains an IR mask and two-
sided transparent tape.
Installation
Attach the IRP2 to the IR Sensor Window
Refer to the following instructions and illustration.
1. Identify the clear, flat bottom surface of the IRP2 shell.
2. Apply transparent silicon adhesive (not supplied) to the flat side of the
IRP2 or use the supplied transparent tape.
CAUTION: Test the silicon adhesive on a non-visible area to confirm
that it will not damage material or equipment.
3. Affix the IRP2 in the center of the IR sensor window on the front panel
of the controlled component.
4. Use a piece of non-damaging tape to hold the IRP2 in position while
the silicon adhesive cures.
5. Remove the tape after the silicon cures.
6. In some cases, identifying the exact location of the sensor window may
be difficult. Consult the owner manual of the unit, or the manufacturer
for the exact IR window location.
7. If the IRP2 shell must be removed and repositioned for any reason, be
sure to completely remove the silicon adhesive and repeat steps 1
through 5.
2•Infrared Emitter Installation Guide – DOC. 8168A
Crestron IRP2 Infrared Emitter
IR Mask Installation
The IR mask (supplied) is designed to fit over the IRP2 shell, as shown in
the following illustration, so that the sensor window of the controlled
component is completely covered. The IR mask prevents unwanted
external IR signals from passing through or leaking past it. The IR mask
also prevents emitting IR from the IRP2 shell from radiating backward
into the IR sensors of other nearby components.
1. Without removing the adhesive backing from the IR mask, fit the two
pieces together and accurately position them over the IR sensor
window of the component to be controlled.
2. Attach the IRP2 to the sensor window using transparent silicon
adhesive (not supplied). Temporarily tape the IRP2 in place using non-
damaging tape until the silicon cures.
3. If necessary, neatly trim the IR mask. Be sure that it overlaps the
margins of the component IR sensor window.
4. Remove the adhesive backing from the IR mask and position it over
the IR sensor window while pressing down firmly.
Attach the IRP2 to Other Locations
Rather than affixing the low output side of the IRP2 shell directly over the
IR sensor window, the shell can be positioned as much as three feet away
on the axis of the IR sensor window. The high output side of the IRP2
Installation Guide - DOC. 8168A Infrared Emitter •3
Infrared Emitter Crestron IRP2
shell permits control at this greater distance. Placement of the IRP2 on
surfaces just above or below the IR sensor window, as shown in the
following illustrations, may provide a more pleasing aesthetic appearance.
However, be sure to position the IRP2 shell so that the edge of the
component does not block the IR signal.
NOTE: Placing the IRP2 shell on a cabinet door may result in
interruption of the IR signal if the door is opened.
Possible mounting locations of the IRP2 shell include being attached to a
shelf directly below or above the IR sensor window.
Front View
Side View
Connect the IRP2
Insert the two-pin connector of the IRP2 into an infrared - serial output
port of the control system as shown in the following illustration.
4•Infrared Emitter Installation Guide – DOC. 8168A
Crestron IRP2 Infrared Emitter
NOTE: The white-traced wire connects to the pin labeled S.
Further Inquiries
If you cannot locate specific information or have questions after reviewing
this guide, please take advantage of Crestron’s award winning customer
service team by calling the Crestron corporate headquarters at
1-888-CRESTRON [1-888-273-7876]. For assistance in your local time
zone, refer to the Crestron website (http://www.crestron.com) for a
listing of Crestron worldwide offices.
You can also log onto the online help section of the Crestron website to
ask questions about Crestron products. First-time users will need to
establish a user account to fully benefit from all available features.
Installation Guide - DOC. 8168A Infrared Emitter •5
Infrared Emitter Crestron IRP2
As of the date of manufacture, the IRP2 has been tested and found to
comply with specifications for CE marking and standards per EMC and
Radiocommunications Compliance Labelling.
NOTE: This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Future Updates
As Crestron improves functions, adds new features, and extends the
capabilities of this product, additional information may be made available
as manual updates. These updates are solely electronic and serve as
intermediary supplements prior to the release of a complete technical
documentation revision.
Check the Crestron website periodically for manual update availability
and its relevance. Updates are identified as an “Addendum” in the
Download column.
6•Infrared Emitter Installation Guide – DOC. 8168A
Andere Handbücher für IRP2
2
Inhaltsverzeichnis
Andere Crestron Computerhardware Handbücher
Crestron
Crestron CNXRY-16 Bedienungsanleitung
Crestron
Crestron 3 Series Bedienungsanleitung
Crestron
Crestron UPX-OS4GB-MSO-2007 Bedienungsanleitung
Crestron
Crestron UPX-2 Bedienungsanleitung
Crestron
Crestron 3 Series Bedienungsanleitung
Crestron
Crestron CNXIR-8 Bedienungsanleitung
Crestron
Crestron CNX-PAD8A Bedienungsanleitung
Crestron
Crestron Four-Way Coupler SRD-CPL-4 Bedienungsanleitung
Crestron
Crestron CNXAO-8 Bedienungsanleitung
Crestron
Crestron PC4-R Bedienungsanleitung
Crestron
Crestron DGE-100 Bedienungsanleitung
Crestron
Crestron C2COM-2 Anleitung zur Verwendung
Crestron
Crestron 4 Series Bedienungsanleitung
Crestron
Crestron ST-CP Bedienungsanleitung
Crestron
Crestron DVPHD Bedienungsanleitung
Crestron
Crestron C2IR-8 Anleitung zur Verwendung
Crestron
Crestron DigitalMedia DMC-VID4 Bedienungsanleitung
Crestron
Crestron C2ENET-1 Anleitung zur Verwendung
Crestron
Crestron C2VEQ-4 Anleitung zur Verwendung
Crestron
Crestron CNXCOM-2 Bedienungsanleitung
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
