Cross Technologies 2017-03A Bedienungsanleitung

Instruction Manual

Model 2017-03A

Up/Downconverter

July 2019, Rev. I

EXECUTE

MODEL 2017

CROSS TECHNOLOGIES INC.

U F=1525 G=+00

D F=1525 G=+25

MUTE

UPCONVERTERDOWNCONVERTER

REMOTEALARM POWER ALARM

UP/DOWNCONVERTER

Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc., but may be

reproduced or duplicated without the prior permission of Cross Technologies, Inc. for purposes of operating

the equipment.

When ordering parts from Cross Technologies, Inc., be sure to include the equipment model number,

equipment serial number, and a description of the part.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

INSTRUCTION MANUAL

MODEL 2017-03A Up/Downconverter

TABLE OF CONTENTS PAGE

Warranty 2

1.0 General 3

1.1 Equipment Description 3

1.2 Technical Characteristics 4

1.3 Monitor & Control Interface 5

1.4 Environmental Use Information 8

2.0 Installation 9

2.1 Mechanical 9

2.2 Rear I/O’s 10

2.3 Front Panel Controls, Indicators 12

2.4 Operation 13

2.5 Menu Settings 15

WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.

All Cross Technologies, Inc. products are warranted against defective materials and

workmanship for a period of one year after shipment to customer. Cross Technologies, Inc.’s

obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s option,

replacing parts, subassemblies, or entire assemblies. Cross Technologies, Inc. shall not be

liable for any special, indirect, or consequential damages. This warranty does not cover parts

or equipment which have been subject to misuse, negligence, or accident by the customer

during use. All shipping costs for warranty repairs will be prepaid by the customer. There

are not other warranties, express or implied, except as stated herein.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

2017-03A Manual, Rev. I Page 2 07/22/19

MODEL 2017-03A Up/Downconverter

1.0 General

1.1 Equipment Description

The 2017-03A L-band Up/Downconverter converts 70 MHz to 950-1525 MHz (Up) and 950-1525 MHz to 70

MHz (Down) in 1 MHz steps with low group delay and flat frequency response. The 2017-03A has lower RF

level out of the upconverter and higher RF level into the downconverter than the 2017-03 and is typically used

to interface an L-band modem to a 70 MHz IF upconverter and downconverter. Multi-function push button

switches select the RF frequency, gain, and other parameters. Front panel LEDs provide indication of DC power

(green), PLL alarm for up and downconverters (red), remote operation (yellow), and Upconverter mute

(yellow). Gain can be manually adjusted over a -25 to +15 dB range for the upconverter and over a 0 to +50 dB

range for the downconverter by the front panel multi-function push-button switches. Remote operation allows

selection of frequency and gain. Parameter selection and frequency and gain settings appear on the LCD

display. Connectors are BNC female for IF and the optional external reference input and output, and Type F

female for RF. A high stability (±0.01ppm) option is also available. It is powered by a 100-240 ± 10% VAC

power supply and housed in a 1.75” X 19” X 16” 1RU chassis.

EXECUTE

MODEL 2017

CROSS TECHNOLOGIES INC.

U F=1525 G=+00

D F=1525 G=+25

MUTE

UPCONVERTERDOWNCONVERTER

REMOTEALARM POWER ALARM

UP/DOWNCONVERTER

FRONT PANEL

AC UPCONVERTER

RF OUTSSPB FUSE

GND

DOWNCONVERTER

J4 J5J3J18J2

RF IN 10 MHZ REF 10 MHZ IF IN

EXT REF F2

LNB FUSE

IF OUT OUTPUT INPUT

DS8 DS7

VDC on RF VDC on RF

J10

AND

MONITOR

CONTROL

15 23

REAR PANEL

Figure 1.1 Model 2017-03A Front and Rear Panels

MHz

OUT

.95

1.525

GHz

1750 MHz

1820

MHz 2.7

3.3

GHz

.95 to 1.525 GHz

BP 120 MHz

CONTROLLER U F=1525 G=+00.0

D F=1450 G=+25.0

.95 -1.525 GHz

MHz

.95

1.525

GHz

OUT

1750 MHz

1680

1820

MHz

2.7

3.3

GHz

REF REF

REF TO

VCOS

var

atten

10MHz*

+24VDC*

10MHz*

+24VDC*

EXT

10MHz*

*OPTIONAL

var

atten var

atten

INT

10MHz

Figure 1.2 Model 2017-03A Up/Downconverter Block Diagram

2017-03A Manual, Rev. I Page 3 07/22/19

1.2 Technical Characteristics

TABLE 1.0 2017-03A Up/Downconverter Specifications*

---UPCONVERTER---

Input Characteristics (IF)

Impedance/Return Loss 75 Ω/18 dB

Frequency 70 ± 18 MHZ

Input Level -40 to -10 dBm

Output Characteristics (RF)

Impedance/Return Loss 75 Ω/12 dB

Frequency 950 to 1525 MHz

Output level -35 to -15 dBm

Output 1 dB compression -10 dBm

Channel Characteristics

Gain range (adjustable) -25 to +15 dBm, 1 dB steps

Frequency Sense Non-inverting

---UP & DOWNCONVERTER---

Channel Characteristics

Frequency Response ± 1.5 dB, entire band; ± 0.5 dB, 36 MHz BW

Spurious Response <-50 dBC

Group Delay, max. 0.01 ns/MHz2parabolic; 0.03 ns/MHz linear; 1 ns ripple

Synthesizer Characteristics

Frequency Accuracy ±1.0 ppm internal reference (±0.01 ppm option H) internal reference

Frequency Step 1 MHz (125 kHz, option X)

-120-100-85-75-75

1MHz100kHz10KHz1KHz100

dBC/Hz

Phase

Noise

(

)

10MHz Level (In/Out) 3 dBm ± 3 dB, 75 ohms (option -E)

Controls, Indicators

Frequency Selection Direct readout LCD; pushbutton switches or remote selection

Gain Selection Direct readout LCD; pushbutton switches or remote selection

Power; Alarm; Rem; Mute Green LED; Red LED; Yellow LED; Red LED

Remote RS232C, 9600 baud (RS485, option Q)

Other

RF Connectors Type F (female) (see Table 2.2 for connector options)

IF Connectors BNC (female) (see Table 2.2 for connector options)

10MHz Connectors BNC (female), 50/75 Ω(option E)

Alarm/Remote Connector DB9, male - NO or NC contact closure on alarm

Size 19 inch standard chassis 1.75” high X 16.0” deep

Power 100 - 240 (±10% VAC), 47 - 63 Hz, 25 watts max.

Options

E - External 10 MHz ref Connectors/Impedance

H - High Stability (±0.01ppm) internal ref B - 75ΩBNC (RF), 75ΩBNC (IF)

Q - RS485 Remote Interface C - 50ΩBNC (RF), 75ΩBNC (IF)

L- LNB Voltage, +24VDC, 0.5 amps D - 50ΩBNC (RF), 50ΩBNC (IF)

T - Temperature Sensor J - 75ΩF-type (RF), 50ΩBNC (IF)

V - SSPB Voltage, +24 VDC, 2.5 Amps N - 50ΩN-type (RF), 75ΩBNC (IF)

X - 125 kHz frequency steps M - 50ΩN-type (RF), 50ΩBNC (IF)

X1 or X1- 125 or 100 kHz Frequency Steps

Connector Options: See Table 2.2

*+10˚C to +40˚C; Specifications subject to change without notice

2017-03A Manual, Rev. I Page 4 07/22/19

---DOWNCONVERTER---

Input Characteristics (RF)

Impedance/Return Loss 75Ω/12 dB

Frequency 950 to 1525 MHz

Noise Figure, Max. 15 dB @ max. gain

Input Level range -60 to -10 dBm

Input 1 dB compression -5 dBm @ 0 dB gain

Output Characteristics (IF)

Impedance/Return Loss 75 Ω/18 dB

Frequency 70 ± 18 MHZ

Output Level -10 to 0 dBm

Output 1 dB compression +5 dBm

Channel Characteristics

Gain range (adjustable) 0 to +50 dB

Image Rejection > 50 dB, min.

Frequency Sense Inverting

Non-inverting

1.3 Monitor and Control Interface

A) Remote Serial Interface

Protocol: RS-232C, 9600 baud rate, no parity, 8 data bits, 1 start bit, and 1 stop bit.

(RS-232C, RS-422, or RS-485 - option Q)

Female DB-9

PC Com Port Male DB-9

2015/16/17 M&C Port

M&C Cable Diagram - Cross Technologies Frequency Converters

RX RX

TX TX

DTR

DSR

RTS

CTS

Connector: Rear panel, DB-9 male

J10 Pinouts

(RS-232C/422/485)

Pinouts (RS-232C/422/485)

Pin Function

1 Rx-

2 Rx+ (RS-232C)

3 Tx+ (RS-232C)

4Tx-

5GND

6 Alarm Relay: Common

7 Alarm Relay: Normally Open

8 Not Used

9 Alarm Relay: Normally Closed

2017-03A Manual, Rev. I Page 5 07/22/19

B) Status Requests

Table 1.1 lists the status requests for the 2017-03A and briefly describes them.

*PLEASE NOTE: The two character {aa}(00-31) prefix, in the table below,

should be used ONLY when RS-485, (OPTION-Q), is selected.

Table 1.1 2017-03A Status Reqquests

Status Requests

Command Syntax* Description

Command Status {aaS1} Returns {aaS1bbbbccccdddeeffLMNOP} where:

• bbbb = Tx frequency

4 characters - standard (7 characters - Option-X)

• cccc = Rx frequency

4 characters - standard (7 characters - Option-X)

• ddd = Tx gain (-10 to 30)

• ee = Rx gain (00 to 50)

• ff = Tx input level (10 to 40 => -10 to -40 dBm)

• L = 0 - non-inverted Receiver; L = 1 - inverted

• M = 0 - Receiver synth alarm

• N = 0 - Transmitter synth alarm

• O = 0 - Summary alarm

• P = 0 - Transmit signal disabled (muted)

External 10MHz (option E) {aaS2} Returns {aaS2bcd} where:

• b = 1 - External 10MHz selected

• c = 1 - 10MHz inserted on upconverter RF (J5)

• d = 1 - 10MHz inserted on downconverter RF (J2)

LNB Current (option L) {aaS3} Returns {aaS3bb} where:

• bb = LNB current, range 00 to 50 (0 to 500 ma)

SSPB Current (option V) {aaS4} Returns {aaS4bbb} where:

• bbb = SSPB current, range 000 to 250 (0 to 2500 ma)

2017-03A Manual, Rev. I Page 6 07/22/19

C) Commands

Table 1.2 lists the commands for the 2017-03A and briefly describes them. After a command is sent the

2017-03A sends a return “>” indicating the command has been received and executed.

General Command Format - The general command format is {aaCND...}, where:

{ = start byte

aa = address (RS-485 only option Q)

C = 1 character, either C (command) or S (status)

N = 1 character command or status request

D = 1 character or more of data (depends on command)

} = stop byte

*PLEASE NOTE: The two character {aa}(00-31) prefix, in the table below,

should be used ONLY when RS-485, (OPTION-Q), is selected.

Table 1.2 2017-03A Commands

Command Syntax* Description

Set Transmitter Frequency {aaC1xxxx} where:

• xxxx = 4 characters standard (7 characters -Option-X)

• Range: 0950 to 1525 MHz

Set Transmitter Input Level {aaCIxx} where:

• xx = 2 characters

• Range: 10 to 40 (-10 to -40 dBm)

Set Receiver Frequency {aaC2xxxx} where:

• xxxx = 4 characters standard (7 characters -Option-X)

• Range: 0950 to 1525 MHz

Set Transmit Gain {aaC3xxxx} where:

• xxxx = 2 or 3 characters

• Range: -25 to +15 (-25 to +15 dB, in 1 dB steps)

Set Receiver Gain {aaC4xxx} where:

• xx = 2 characters

• Range: 00 to 50 (00 dB to 50 dB, in 1 dB steps)

Enable Tx {aaCAx} where x =:

• 0 to disable Tx signal

• 1 to enable Tx signal

External 10MHz (option E) {aaCEx} where x =:

• 0 to disable External 10MHz ref signal

• 1 to enable External 10MHz ref signal

Insert 10MHz on UP RF (option E) {aaC5x} where x =:

• 0 to disable 10MHz upconverter insertion on RF (J5)

• 1 to enable 10MHz upconverter insertion on RF (J5)

Insert 10MHz on DOWN RF (option E) {aaC6x} where x =:

• 0 to disable 10MHz downconverter insertion on RF (J2)

• 1 to enable 10MHz downconverter insertion on RF (J2)

Downconverter Spectrum {aaC7x} where x =:

• 0 for non-inverted

• 1 for inverted

Enable Remote # Just # sign

Disable Remote {aaCR0}* {CR and zero}

2017-03A Manual, Rev. I Page 7 07/22/19

1.4 Environmental Use Information

A.Elevated operating ambient temperature - if installed in a closed or multi-unit rack assembly,

the operating ambient temperature of the rack may be greater than room ambient temperature.

Therefore, consideration should be given to Tmra.

B. Reduced air flow - Installation of the equipment in a rack should be such that the amount of air flow

required for safe operation of the equipment is not compromised. Additional space between unit

may be required.

C. Mechanical loading - Mounting of equipment in a rack should be such that a hazardous condition

does not exist due to uneven weight distribution.

D. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply

circuit and the effect that overloading of circuits could have on over current protection and supply wiring.

Appropriate consideration of equipment name plate rating should be used, when addressing this concern.

E. Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular

attention should be given to supply connections other than direct connection to the Branch

(use of power strips).

F. Top Cover - There are no serviceable parts inside the product so, the Top Cover should not be removed.

If the Top Cover is removed the ground strap and associated screw MUST BE REINSTALLED

prior to Top Cover screw replacement. FAILURE TO DO this may cause INGRESS and/or EGRESS

emission problems.

2017-03A Manual, Rev. I Page 8 07/22/19

2.0 Installation

2.1 Mechanical - The 2017-03A consists of one RF/Controller PCB housed in a 1 RU (1 3/4 inch high) by 16

inch deep chassis. A switching, ± 12, +5, +24 VDC power supply provides power for the assemblies. The 2017-

03A can be secured to a rack using the 4 holes on the front panel. Figure 2.0 shows how the 2017-03A is

assembled.

POWER

SUPPLY

Figure 2.0 Model 2017-03A Mechanical Assembly

2017-03A Manual, Rev. I Page 9 07/22/19

2.2 Rear Panel Input/Output Signals and Control -

Figure 2.2 shows the input and output connectors on the rear panel.

GND

J18J2

RF IN 10 MHZ REF

OUTPUT

AC1 - POWER IN

AC input for switching power

supply. 100-240 ± 10% VAC,

47-63 Hz.

J2 - RF IN

950-1525 MHz input, -60

to -10 dBm, see Table 2.2.

J1 - IF OUT

70 MHz output, -10 to 0

dBm, See Table 2.2.

J10

AND

MONITOR

CONTROL

J10 - MONITOR AND CONTROL

DB9 female connector. see Table

2.1.

RF OUT

J4 J5J3

10 MHZ IF IN

EXT REF

J3 - 10 MHz EXT REF INPUT (Option -E)

10 MHz external reference input, 0 ± 3 dBm, 75

ohms, BNC female connector.

J5 - RF OUT

950-1525 MHz output,

-35 to -15 dBm out, see Table 2.2.

J4 - IF IN

70 MHz input, -40 to -10

dBm in, see Table 2.2.

SSPB FUSE

F2 - SSPB FUSE (option -V)

2.5A, Fast Blo, 1/4” Fuse;

installing fuse places +24

VDC, 2.5 amp, max. on the

RF OUT (J5 center pin).

F1 - LNB FUSE (option -L)

0.5A, Fast Blo, 1/4” Fuse; installing

fuse places +24 VDC, 0.4 Amps,

max. on the RF IN

(J2 center pin).

LNB FUSE

DOWNCONVERTER

UPCONVERTER

IF OUT

DS8

VDC on RF

DS7

VDC on RF

INPUT

DS7 - SSPB ALARM LED (option -V)

Lights yellow when +24 VDC SSPB voltage is

present on RF OUT, J5, center pin.

DS8 - LNB ALARM LED (option -L)

Lights yellow when +24 VDC LNB

voltage is present on RF IN, J2, center

pin.

J18 - 10 MHz REF OUTPUT (option -E)

10 MHz reference output. 75ΩBNC

female connector.

Figure 2.1 Model 2017-03A Rear Panel I/O’s

Shown below (Option P48) - Rear Panel Input/Output Signals with

Option P48, 48 VDC nominal 36-72 VDC, 2.5A maximum.

INT AUTO EXT

GND

J102

AND

MONITOR

CONTROL

36 TO 72 VDC

• •

DC INPUT

J14 S1

J2 J101 J111 UPCON

J112

RF2 IN

RF2 OUT

J11

RF1 IN

DOWNCON

J102

RF2 OUT

RF1 OUT

EXT REF

IN RF

OUT

2017-03A Manual, Rev. I Page 10 07/22/19

Andere Cross Technologies Medienkonverter Handbücher

Cross Technologies

Cross Technologies 2016-8085 Bedienungsanleitung

Cross Technologies

Cross Technologies 2117-7172 Bedienungsanleitung

Cross Technologies

Cross Technologies 2009-2425-1750 Bedienungsanleitung

Cross Technologies

Cross Technologies 2415-02 Series Bedienungsanleitung

Cross Technologies

Cross Technologies 3116-7786-2150 Bedienungsanleitung

Cross Technologies

Cross Technologies 2017-93 Bedienungsanleitung

Cross Technologies

Cross Technologies 2016-25-01 Bedienungsanleitung

Cross Technologies

Cross Technologies 2116-184 Bedienungsanleitung

Cross Technologies

Cross Technologies 3116-22-23 Bedienungsanleitung

Cross Technologies

Cross Technologies 4115-41-212 Bedienungsanleitung

Cross Technologies

Cross Technologies 2016-25 Bedienungsanleitung

Cross Technologies

Cross Technologies 2416-x02 Bedienungsanleitung

Cross Technologies

Cross Technologies 2005-02P4 Bedienungsanleitung

Cross Technologies

Cross Technologies 2005 Bedienungsanleitung

Cross Technologies

Cross Technologies 2116-182193 Bedienungsanleitung

Cross Technologies

Cross Technologies 2016-75-213 Bedienungsanleitung

Cross Technologies

Cross Technologies 2117 Bedienungsanleitung

Cross Technologies

Cross Technologies 2017-03 Bedienungsanleitung

Cross Technologies

Cross Technologies 2099-2424 Bedienungsanleitung

Cross Technologies

Cross Technologies 4116-31-184 Bedienungsanleitung

Cross Technologies

Cross Technologies 2016-05A Bedienungsanleitung

Cross Technologies

Cross Technologies 2099-10 Bedienungsanleitung

Cross Technologies

Cross Technologies 4115-300 Bedienungsanleitung

Cross Technologies

Cross Technologies 1584 Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung