Cross Technologies 1584 Bedienungsanleitung
Instruction Manual
Model 1584-18/18S
RF Splitter
November 2018, Rev. C
MODEL 1584 CROSS TECHNOLOGIES INC.
A
POWER
SPLITTER
BLNB VOLTAGE
ON
GND +DC
Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc.,
but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc.
for purposes of operating the equipment.
When ordering parts from Cross Technologies, Inc., be sure to include the equipment
model number, equipment serial number, and a description of the part.
CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
(770) 886-8005
FAX (770) 886-7964
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL [email protected]
INSTRUCTION MANUAL
MODEL 1584-18/18S, 16-Way Splitter
TABLE OF CONTENTS PAGE
Warranty 2
1.0 General 3
1.1 Equipment Description 3
1.2 Technical Characteristics 4
2.0 Installation 5
2.1 Mechanical 5
2.2 Rear Panel Input/Output Connectors 6
2.3 Front Panel Monitors and Indicators 6
2.4 Operation 7
2.5 Environmental Use Information 8
WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.
All Cross Technologies, Inc. products are warranted against defective materials and
workmanship for a period of one year after shipment to customer. Cross Technologies,
Inc.’s obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s
option, replacing parts, subassemblies, or entire assemblies. Cross Technologies, Inc. shall
not be liable for any special, indirect, or consequential damages. This warranty does not
cover parts or equipment which have been subject to misuse, negligence, or accident by the
customer during use. All shipping costs for warranty repairs will be prepaid by the
customer. There are no other warranties, express or implied, except as stated herein.
CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
(770) 886-8005
FAX (770) 886-7964
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL [email protected]
1584-18/18S Manual_ Rev. C Page 2 11/07/18
MODEL 1584-18/18S Splitter
1.0 General
1.1 Equipment Description
The Model 1584-18/18S* is one eight-way, 0.95 - 2.05 GHz, 0 dB gain splitter in a 1RU rack mount chassis
with redundant 100-240 ± 10% VAC power supplies. The splitter provides fused LNB DC power insertion and
surge protection on the RF input, and provides excellent RF characteristics. The splitter has eight outputs on the
back panel, and fused LNB power can be inserted on the input. Two individual 100-240 ± 10% VAC input
power supplies provide diode OR’d redundant power to the unit*. The LNB power line is separately fused. A
surge suppressor on the splitter input protects against high voltage transients. On the front panel, two green
LED’s indicate the presence of DC voltage from each of the two power supplies, and another green LED
indicates LNB power insertion. LNB voltage test points are also provided on the front panel to monitor the LNB
voltage. *LNB Power Insertion feature NOT available on 1584-18S model.
MODEL 1584 CROSS TECHNOLOGIES INC.
A
POWER
SPLITTER
BLNB VOLTAGE
ON
GND +DC
FRONT PANEL*
AC A AC B
GND
JI
J2J3J4
J5J6J7J8J9
J10J11J12
J17 J13J14J15J16
IN
FUSE F1
SPLITTER
OUT OUTOUTOUTOUTOUTOUT OUTOUTOUT OUT OUTOUTOUT OUTOUT
REAR PANEL*
FIGURE 1.1 MODEL 1584-18/18S FRONT AND REAR PANELS
1584-18/18S Block Diagram
AMP
DC
INS
SURGE
SUPPRESS
FUSE
8 WAY
SPLITTER
OUT 1
OUT 2
OUT 8
1 - 2
GHz
IN
1 - 2 GHz OUT
FIGURE 1.2 MODEL 1584-18/18S Block Diagram
*NOTE: Model 1584-18/18S has a single non-redundant, switching power supply.
1584-18/18S Manual_ Rev. C Page 3 11/07/18
1.2 Technical Characteristics
TABLE 1.0 1584-18/18S SPECIFICATIONS
Characteristics Specifications**
Input Characteristics
Input Impedance 75Ω(50Ω, Option -D)
Return Loss 12 dB minimum; 14 dB typical
Input Level -20 dBm total maximum
(No Damage +10 dBm)
Output Characteristics
Impedance 75Ω(50Ω, Option -D)
Return Loss 12 dB minimum.; 14 dB typical
In-Band Characteristics
Gain +0 dB ±1.0 dB
Frequency Response ± 1.0 dB; 0.95 to 2.05 GHz
± 0.5 dB, any 20 MHz increment
Port to Port Isolation > 18 dB, 20 dB typical
Indicators
AC Power Green LED indicates DC voltage prior to diode OR
LNB DC Voltage Green LED indicates LNB power insertion on splitter input (J17)
Other
LNB DC Voltage 22 ± 2 VDC
Output LNB current 300 ma, maximum
Surge Suppressor SiDACTOR
RF connectors Type-F (female)
AC Power Redundant switching power supplies,
100-240 ± 10% VAC, 4 -63 Hz, 30 watts maximum
*NOTE: Model 1584-18S has a single non-redundant, Switching
Power Supply and does NOT provide the LNB Power Insertion Feature.
Mechanical 19 inch standard chassis 1.75” high X 12” deep
Options
-B 75ΩBNC, RF Connectors
-D 50ΩBNC, RF Connectors
-E External 10 MHz Reference Input with Insertion
-W9 DC (24 vdc/2.5A) Power By-pass
**+10˚C to +40˚C; Specifications subject to change without notice.
1584-18/18S Manual_ Rev. C Page 4 11/07/18
2.0 Installation
2.1 Mechanical - The 1584-18/18S consists of one RF printed circuit board (PCB) housed in a 1 RU (1.75 inch
high) by 12 inch deep chassis. Redundant, switching, +24 VDC power supplies with the DC output diode OR’d
provide redundant power for the internal and external amplifiers and LEDs. (Model 1584-18/18S has a single
non-redundant, switching power supply). Connectors are type F, female for the RF connections (BNC, female
option -B or -D). The 1584-18/18S can be secured to a rack using the 4 holes on the front panel. Figure 2.0
shows how the 1584-18/18S is assembled. J25 connects DC Power to the fuse as shown and J30 and J29
connect the DC voltage from the power supplies to the PCB as shown.
POWER
SUPPLY
A
2 1
J29
+24 PS IN (AC A)
PIN 1, +24 VDC
PIN 2, GROUND
POWER
SUPPLY
B
NOTE:
Model 1584-18S has
a single
non-redundant,
switching power
supply.
J30
+24 PS IN (AC B)
PIN 1, +24 VDC
PIN 2, GROUND
J25
LNB FUSE
PIN 1, LNB SIDE
PIN 2, +22 VDC SIDE
2 1
1
2
FIGURE 2.0 1584-18/18S MECHANICAL ASSEMBLY
1584-18/18S Manual_ Rev. C Page 5 11/07/18
2.2 Rear Panel Input/Output Connectors
The input and output connectors on the rear panel are shown in Figure 2.1.
CAUTION! IF A FUSE IS INSTALLED IN THE FUSE F1 HOLDER, +22 VDC WILL APPEAR
ON THE SPLITTER INPUT CONNECTOR (J17) CENTER PIN.
AC A INPUT
100-240 ±10% VAC,
47-60 HZUses 2 amp
Slow Blo, 5mm fuse.
J17 - SPLITTER INPUT
Type F (female) 75 Ω.
See Table 2.0 for other
connector options.
J16, J15, J14, J13, J12, J11, J10, J9 - SPLITTER OUTPUTS
Type F (female) 75Ω. Terminate when not used.
See Table 2.0 for other connector options.
AC B INPUT
100-240 ±10% VAC, 47-
60 HZ. Uses 2 amp
Slow Blo, 5mm fuse.
AC A AC B
GND
JI
J2J3J4J5J6J7J8J9
J10J11J12
J17 J13J14J15J16
IN
FUSE F1
SPLITTER
FIGURE 2.1 1584-18/18S REAR PANEL
*NOTE: Model 1584-18/18S has a single non-redundant, switching power supply.
External 10 MHz Reference Input, with insertionE -
DC (24 vdc / 2.5A) Power SupplyW9 -
BNC, 50ΩD -
BNC, 75ΩB -
STD Type F, 75Ω
RF ConnectorsOption
Table 2.0 RF Connector Options
2.3 Front Panel Monitors and Indicators
Figure 2.2 shows the front panel monitors and indicators.
DS6 - POWER LED B*
Lights green when DC voltage
is present from AC B power supply.
TP1 - +DC TEST POINT
Used to measure the LNB voltage.
22 ±2 VDC typical
DS5 - POWER LED A
Lights green when DC
voltage is present from AC A
power supply.
TP5 - GND TEST POINT
Used to measure the LNB voltage. DS1 - LNB VOLTAGE LED
Lights Green when LNB voltage is present
on the Splitter input (J17) center pin.
A
POWER
BLNB VOLTAGE
ON
GND +DC
MODEL 1584
SPLITTER CROSS TECHNOLOGIES INC.
FIGURE 2.2 1584-18/18S FRONT PANEL
1584-18/18S Manual_ Rev. C Page 6 11/07/18
2.4 Operation
1. Connect RF cables to the 1584-18/18S (See Section 2.2).
2. IF DC VOLTAGE IS REQUIRED ON THE SPLITTER RF INPUT (J17) CENTER CONDUCTOR,
install 1/4”, 0.5 amp fast blo fuses in the FUSE F1 holder
3. Connect 100-240 ± 10% VAC, 47 - 63 Hz to AC A and AC B on the back panel and observe
A and B LEDs are lit on the front panel.*
4. Monitor DC voltage to the external LNB amplifier (Front panel Green ON LED should be lit if
LNB fuse is installed in the rear panel fuse holder) to insure proper voltage.
CAUTION! IF A FUSE IS INSTALLED IN THE FUSE F1 HOLDER, +22 VDC WILL APPEAR
ON THE SPLITTER INPUT CONNECTOR (J17) CENTER PIN.
NOTE: FOR OPTIMUM PERFORMANCE, THE SPLITTER PORTS SHOULD BE TERMINATED
WITH 75 OHM TYPE F TERMINATION WHEN NOT USED.
AC Fuse - The fuse is a 5mm, 2 amp slow blo and is inserted in the far slot in the drawer below the AC
input as shown in Figure 2.6. There is a spare fuse in the near slot. If a fuse continues to open, the power
supply is most likely defective. Note that each power supply module within the chassis also has a fuse
but failure of this fuse indicates the power supply may be defective.
AC Fuse - 2 amp slow blow (Type T),
5 mm X 20 mm
FUSE DRAWER
SPARE FUSE
~
INPUT
100-240± 10%VAC
47-63 Hz
2A MA
X
FUSE
TYPE T 2A GDC
250 VOL
T
FOR 100 - 240 V~
~
FIGURE 2.6 FUSE LOCATION AND SPARE FUSE
1584-18/18S Manual_ Rev. C Page 7 11/07/18
2.5 Environmental Use Information
A.Rack-Mounting - To mount this equipment in a rack, please refer to the installation instructions
located in the user manual furnished by the manufacturer of your equipment rack.
B. Mechanical loading - Mounting of equipment in a rack should be such that a hazardous condition
does not exist due to uneven weight distribution.
C.Elevated operating ambient temperature - If installed in a closed or multi-unit rack assembly,
the operating ambient temperature of the rack may be greater than room ambient temperature.
Therefore, consideration should be given to Tmra.
D. Reduced air flow - Installation of the equipment in a rack should be such that the amount of air flow
required for safe operation of the equipment is not compromised. Additional space between unit
may be required.
E. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply
circuit and the effect that overloading of circuits could have on over current protection and supply wiring.
Appropriate consideration of equipment name plate rating should be used, when addressing this concern.
F. Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular
attention should be given to supply connections other than direct connection to the Branch
(use of power strips).
G. Top Cover - There are no serviceable parts inside the product so, the Top Cover should not be removed.
If the Top Cover is removed the ground strap and associated screw MUST BE REINSTALLED
prior to Top Cover screw replacement. FAILURE TO DO this may cause INGRESS and/or EGRESS
emission problems.
1584-18/18S Manual_ Rev. C Page 8 11/07/18
CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
(770) 886-8005
FAX (770) 886-7964
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL [email protected]
Printed in USA
1584-18/18S Manual_ Rev. C Page 9 11/07/18
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Cross Technologies Medienkonverter Handbücher
Cross Technologies
Cross Technologies 2015-26 Bedienungsanleitung
Cross Technologies
Cross Technologies 3117-3338 720 Series Bedienungsanleitung
Cross Technologies
Cross Technologies 2005-10 Bedienungsanleitung
Cross Technologies
Cross Technologies 2016-75-213 Bedienungsanleitung
Cross Technologies
Cross Technologies 2015-58T Bedienungsanleitung
Cross Technologies
Cross Technologies 2005-02P4 Bedienungsanleitung
Cross Technologies
Cross Technologies 2117 Bedienungsanleitung
Cross Technologies
Cross Technologies 3116-145-1600 Bedienungsanleitung
Cross Technologies
Cross Technologies 2016-8085 Bedienungsanleitung
Cross Technologies
Cross Technologies 2016-26 Bedienungsanleitung
Cross Technologies
Cross Technologies 2416-x02 Bedienungsanleitung
Cross Technologies
Cross Technologies 2017-03 Bedienungsanleitung
Cross Technologies
Cross Technologies 2115-275-1845 Bedienungsanleitung
Cross Technologies
Cross Technologies 2009-2425-1750 Bedienungsanleitung
Cross Technologies
Cross Technologies 2015-123 Bedienungsanleitung
Cross Technologies
Cross Technologies 2016-25-01 Bedienungsanleitung
Cross Technologies
Cross Technologies 4115-41-212 Bedienungsanleitung
Cross Technologies
Cross Technologies 2416 25 Series Bedienungsanleitung
Cross Technologies
Cross Technologies 4115-300 Bedienungsanleitung
Cross Technologies
Cross Technologies 2016-02-1200 Bedienungsanleitung
