CTA ADD-ADMA Bedienungsanleitung

Articulating Desk Mount Arm with VESA Plate

ADD-ADMA

CONTENTS:

INSTRUCTIONS:

2A. When the C-Clamp is securely

attached to a surface, use the

provided security tool (C), attach to

security component, and rotate

closewise to put the C-Clamp in an

‘locked’ state. To loosen, rotate

counterclockwise with the security

tool.

Remove arm (D) from the

base clamp mount. Repeat

steps in reverse order to

re-install connection

2B. Align the (2) dimples on the underneath of the

security tool into the two holes on the security

component on the clamp as shown above

2C. Rotate counter-clockwise to

loosen and place the clamp in an

‘unlocked’ state. Continue rotating

until there is enough slack to rotate

the knob.Turn it clockwise to tighten

and place the clamp in a ‘locked’

state.

BASE CLAMP SECURITY SETUP

BASE MOUNT INSTALLATION ARM & BASE CLAMP

ADJUSTMENTS

If you need to remove the arm

from the base clamp, take the

provided tool (B), rotate, and

loosen connection.

Find the included base

pad (E) and peel off the

backing. Align to the

underneath of the

C-Clamp (D) and apply

pad. While the clamp is in unlocked mode, rotate the

knob at the bottom (as shown above) to loosen

or securely tighten to the table top.

ALIGNING SECURITY TOOL WITH SECURITY COMPONENT

Articulating Desk Mount Arm with VESA Plate

ADD-ADMA

Each hinge of the product can be

adjusted easily with the provided tool (A).

Loosen to adjust and securely tighten

after preferred position is set.

When all hinges and joints are tightened, do not attempt to

forcibly flex the angles or positioning without loosening. Any

attempt to do so will possibly have an effect on product integrity

and CTA and manufacturer will not be responsible for any

mishandling.

JOINT ADJUSTMENTS

When routing cables from

device to the power source, use

provided clips (F) as shown to keep

the cables organized and tight to

the arms to avoid any slack.

CABLE

ROUTING

Inhaltsverzeichnis

Andere CTA Rack & Stand Handbücher

CTA

CTA PAD-CHKWDC Bedienungsanleitung

CTA

CTA PAD-MFSV Bedienungsanleitung

CTA

CTA PAD-ASKB10 Bedienungsanleitung

CTA

CTA PAD-ASKP Bedienungsanleitung

CTA

CTA ADD-CPOLEGN Bedienungsanleitung

CTA

CTA PAD-WDM Bedienungsanleitung

CTA

CTA PAD-UATPB2 Bedienungsanleitung

CTA

CTA AUT-VDMC Bedienungsanleitung

CTA

CTA ADD-PARAFSV Bedienungsanleitung

CTA

CTA ADD-FS2VDMB Bedienungsanleitung

CTA

CTA PAD-UGT Bedienungsanleitung

CTA

CTA PAD-USGTW Bedienungsanleitung

CTA

CTA PAD-SSMA Bedienungsanleitung

CTA

CTA PAD-DSGK Bedienungsanleitung

CTA

CTA PAD-CFWM Bedienungsanleitung

CTA

CTA CP-CSWMHW Bedienungsanleitung

CTA

CTA PAD-PARAFDC Bedienungsanleitung

CTA

CTA PAD-PF1ICC Bedienungsanleitung

CTA

CTA PAD-SCGS Bedienungsanleitung

CTA

CTA PAD-FTSU Bedienungsanleitung

CTA

CTA PAD-ASK13B Bedienungsanleitung

CTA

CTA PAD-PARAF1 Bedienungsanleitung

CTA

CTA PAD-SWM Bedienungsanleitung

CTA

CTA PAD-TPADM Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung