CYP CPRO-U4T Bedienungsanleitung

CPRO-U4T

4K UHD 1×4 HDMI Splitter

Operation Manual

DISCLAIMERS

The information in this manual has been carefully checked and

is believed to be accurate. Cypress Technology assumes no

responsibility for any infringements of patents or other rights of third

parties which may result from its use.

Cypress Technology assumes no responsibility for any inaccuracies

that may be contained in this document. Cypress also makes no

commitment to update or to keep current the information contained

in this document.

Cypress Technology reserves the right to make improvements to this

document and/or product at any time and without notice.

No part of this document may be reproduced, transmitted,

transcribed, stored in a retrieval system, or any of its part translated

into any language or computer le, in any form or by any means—

electronic, mechanical, magnetic, optical, chemical, manual, or

otherwise—without express written permission and consent from

Cypress Technology.

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be

trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or

operate this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

• Always follow basic safety precautions to reduce the risk of re,

electrical shock and injury to persons.

• To prevent re or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts

inside the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the PSU

if it is damaged.

• Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow for

sufcient space for air to circulate around the unit.

• Please completely disconnect the power when the unit is not in

use to avoid wasting electricity.

REVISION HISTORY

VERSION NO. DATE SUMMARY OF CHANGE

RDV1 16/08/16 Preliminary release

VS1 09/07/18 Final technical review

CONTENTS

1. Introduction......................................................1

2. Applications.....................................................1

3. Package Contents ..........................................1

4. System Requirements......................................1

5. Features............................................................2

6. Operation Controls and Functions.................2

6.1 Front Panel ................................................. 2

6.2 Rear Panel.................................................. 3

7. Connection Diagram ......................................4

8. Specications ..................................................5

8.1 Technical Specications .......................... 5

8.2 Video Specications................................. 6

8.3 Cable Specications ................................ 7

9. Acronyms .........................................................8

1. INTRODUCTION

This 4K UHD HDMI Splitter provides an advanced solution for splitting

and distributing a single HDMI input to 4 HDMI outputs. This distribution

amp provides a high level of audio and video performance with

support for video resolutions up to 4K@60Hz (4:2:0) and high denition

digital audio formats such as LPCM 7.1, with audio sampling rates up

to 192kHz, Bitstream, and HD Bitstream. Standard EDID management

functionality is included and the System Reset function allows the unit

to automatically change the input selection on any connected, CEC

enabled, TVs to the input the unit is currently connected to.

2. APPLICATIONS

• Classroom & Lecture Hall Presentations

• Showrooms & Demo Rooms

• Hotel Lobby Information Displays

• Public Commercial Displays

3. PACKAGE CONTENTS

• 1×1 by 4 HDMI Splitter

• 1×5V/1.2A DC Power Adapter

• 1×Rackmount Ears (Set of 2)

• 1×Shockproof Feet (Set of 4)

• 1×Operation Manual

4. SYSTEM REQUIREMENTS

• HDMI source equipment such as a media player, video game

console or set-top box.

• HDMI receiving equipment such as HDTVs, monitors or audio

ampliers.

• The use of “Premium High Speed HDMI” cables is highly

recommended.

5. FEATURES

• HDMI 2.0 and DVI 1.0 compliant

• HDCP 1.4 compliant

• 1 HDMI input and 4 HDMI outputs

• Supports HD resolutions up to 4096×2160@60Hz (4:2:0, 8-bit)

• Simultaneous display of a single 4K source on up to four 4K displays

• 3D signal support (with 3D source and compatible 3D TV)

• Supports pass-through of audio formats including LPCM 2.0/5.1/7.1,

Bitstream, and HD Bitstream

• System Reset function (CEC active source command)

• EDID management control including “Standard” (Internal EDID)

mode and “TV” (External Display EDID) modes

6. OPERATION CONTROLS AND FUNCTIONS

6.1 Front Panel

POWER IN OUT

1234

EDID SYS-RST

ON OFF

SERVICE

STD TV

1 2 3 4 5 6

1POWER LED: This LED will illuminate to indicate the unit is on and

receiving power.

2IN LED: This LED will illuminate to indicate that a live source has

been detected on the input port. When no source is detected the

LED will remain off.

3OUT LEDs 1~4: These LEDs will illuminate to indicate when a valid

sink has been detected on the associated output port. When no

sink is detected the LED will remain off.

4EDID SWITCH: This switch controls the EDID management behavior

of the unit. When set to “TV” mode the unit will read and store

the EDID from the sink connected to output 1 and pass it to the

connected source. When set to “STD” mode the unit will use a built

in EDID dened as 1080p@60Hz, 8-bit, LPCM 2.0.

5SYS-RST SWITCH: Controls the CEC “active source” reset

functionality of the unit. When switched to the “ON” position

the unit will send a CEC active source reset command to all

connected displays every 8~10 minutes. This command requests

that any connected CEC compliant TVs switch to the input the unit

is connected on.

Note: The connected TV must have CEC support enabled. Not all

HDMI TVs support this CEC command.

6SERVICE: This slot is reserved for rmware update use only.

6.2 Rear Panel

DC 5V

OUT

IN 2

1 2 3

1DC 5V: Plug the 5V DC power adapter into the unit and connect it

to an AC wall outlet for power.

2IN: Connect to HDMI source equipment such as a media player,

game console or set-top box.

3OUT 1~4: Connect to HDMI TVs, monitors or ampliers for digital

video and audio output.

7. CONNECTION DIAGRAM

DC 5V

OUT

IN 2134

Media Player

Power Supply

HDMI Outputs

HDMI Input

UHDTV UHDTV

UHDTVUHDTV

8. SPECIFICATIONS

8.1 Technical Specications

HDMI Bandwidth 340MHz/10.2Gbps

Input Port 1×HDMI

Output Ports 4×HDMI

Power Supply 5V/1.2A DC

(US/EU standards, CE/FCC/UL certied)

ESD Protection Human Body Model:

±8kV (Air Discharge)

±4kV (Contact Discharge)

Dimensions 161mm×22mm×68mm (W×H×D)

[Case Only]

161mm×26mm×76.5mm (W×H×D)

[All Inclusive]

Weight 311g

Chassis Material Metal

Silkscreen Color Black

Operating Temperature 0 ˚C–40 ˚C/32 ˚F–104 ˚F

Storage Temperature -20 ˚C–60 ˚C/-4 ˚F–140 ˚F

Relative Humidity 20–90% RH (Non-condensing)

Power Consumption 1.32W

Inhaltsverzeichnis

Andere CYP Kabel und Steckverbinder Handbücher

CYP

CYP CPRO-8ER Bedienungsanleitung

CYP

CYP CPRO-8E Bedienungsanleitung

CYP

CYP CHDBT-1H2CE Bedienungsanleitung

CYP

CYP CPLUS-V2E Bedienungsanleitung

CYP

CYP CPRO-16E Bedienungsanleitung

CYP

CYP CPRO-U8T Bedienungsanleitung

CYP

CYP CDPS-UA1H10HS Bedienungsanleitung

CYP

CYP PU-1H7HBTE Bedienungsanleitung

CYP

CYP CDP-13DPI Bedienungsanleitung

CYP

CYP CH-526RXPL Bedienungsanleitung

CYP

CYP CMDP-13MDPI Bedienungsanleitung

CYP

CYP CPRO-2E Bedienungsanleitung

CYP

CYP QU-4-4K22 Bedienungsanleitung

CYP

CYP CDPS-UA1H2HS Bedienungsanleitung

CYP

CYP CLUX-18W Bedienungsanleitung

CYP

CYP CPRO-2A Bedienungsanleitung

CYP

CYP DT-12 Bedienungsanleitung

CYP

CYP CPRO-U2T Bedienungsanleitung

CYP

CYP CHDBT-1H7CE Bedienungsanleitung

CYP

CYP CPRO-U8T Bedienungsanleitung

CYP

CYP CLUX-12E Bedienungsanleitung

CYP

CYP CLUX-8M Bedienungsanleitung

CYP

CYP CLUX-18S Bedienungsanleitung

CYP

CYP qu-2-4k22 Bedienungsanleitung

Beliebte Kabel und Steckverbinder Handbücher anderer Marken

Philips

Philips SWA6310 Bedienungsanleitung

StarTech.com

StarTech.com CRJ4550PK Bedienungsanleitung

Nohau

Nohau EMUL-IP2K-PC Bedienungsanleitung

Foxun

Foxun SX-SP144E-HD4K2K Bedienungsanleitung

Philips

Philips SWA3305W Bedienungsanleitung

opticis

opticis Stretch DVIM1-1P0x Bedienungsanleitung

Volkswagen

Volkswagen VAS 6558A Bedienungsanleitung

NEXIBO

NEXIBO N-13 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-u2dhp Bedienungsanleitung

Global Caché

Global Caché Flex Link Blaster Bedienungsanleitung

Hauppauge

Hauppauge USB-Live2 Bedienungsanleitung

Fenix

Fenix MPSV 15 Bedienungsanleitung

BEGA

BEGA 71 085 Bedienungsanleitung

Tesla

Tesla HPWC Bedienungsanleitung

GAMERON

GAMERON LUXURY TV CABLE Bedienungsanleitung

molex

molex Milli-Grid Dual row 87568 Series Bedienungsanleitung

Burndy

Burndy Continental Industries thermOweld CRE-7 Bedienungsanleitung

Chauvet DJ

Chauvet DJ Data Stream 8 Bedienungsanleitung