CYP CHDBT-1H3CL Bedienungsanleitung

CHDBT-1H3CL

1×4 HDMI over HDMI and CAT5e/6/7 Splitter

Operation Manual

DISCLAIMERS

The information in this manual has been carefully checked and

is believed to be accurate. Cypress Technology assumes no

responsibility for any infringements of patents or other rights of third

parties which may result from its use.

Cypress Technology assumes no responsibility for any inaccuracies

that may be contained in this document. Cypress also makes no

commitment to update or to keep current the information contained

in this document.

Cypress Technology reserves the right to make improvements to this

document and/or product at any time and without notice.

No part of this document may be reproduced, transmitted,

transcribed, stored in a retrieval system, or any of its part translated

into any language or computer le, in any form or by any means—

electronic, mechanical, magnetic, optical, chemical, manual, or

otherwise—without express written permission and consent from

Cypress Technology.

Version 1.0 September 2011

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be

trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or

operate this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

• Always follow basic safety precautions to reduce the risk of re,

electrical shock and injury to persons.

• To prevent re or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts

inside the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the PSU

if it is damaged.

• Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow for

sufcient space for air to circulate around the unit.

REVISION HISTORY

VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE

RDV1 27/02/13 Preliminary Release

RDV2 13/06/13 Package Contents

RDV3 17/06/13 Dimension

RDV4 20/06/13 Add IR Cable Pin Dene

RDV5 01/07/13 IR Power

VS1 23/12/13 Updated Text & Diagrams

CONTENTS

1. Introduction............................................ 1

2. Applications........................................... 1

3. Package Contents ................................ 1

4. System Requirements............................ 1

5. Features.................................................. 2

6.1 Front Panel.........................................3

6.2 Rear Panel .........................................4

6.3 IR Cable Pin Assignment ..................5

7. Connection Diagram ............................ 6

8. Specications ........................................ 7

8.1 Technical Specications ..................7

8.2 CAT5e/6/7 Cable Specication ......8

9. Acronyms ............................................... 8

1. INTRODUCTION

The HDMI over HDMI and CAT5e/6/7 Splitter can split and distribute

a single HDMI input and 2-way IR control to up to three CAT5e/6/7

outputs and includes a simultaneous HDMI bypass output. It supports

resolutions up to 1080p Full HD, 4K×2K timing, 3D and multi-channel

digital audio formats (such as LPCM 7.1CH, Dolby TrueHD, Dolby Digital

Plus and DTS-HD). The HDMI bypass output can be connected to an

HDMI display or cascaded to another splitter. The three CAT5e/6/7

outputs can be connected to CAT5e/6/7 to HDMI receivers to extend

the operating distance up to 60 meters.

2. APPLICATIONS

• Household entertainment sharing and control

• Lecture room display and control

• Showroom display and control

• Meeting room presentation and control

• Classroom display and control

3. PACKAGE CONTENTS

• 1×4 HDMI over HDMI and CAT5e/6/7

• 1×IR Receiver

• 1×IR Blaster

• 24V DC Power Adaptor

• Power Cord

• Operation Manual

4. SYSTEM REQUIREMENTS

• HDMI equipped source devices, connect with HDMI cables

• HDMI equipped displays (TVs or monitors) or HDMI equipped AV

receivers, connect with HDMI cables

• Certied CAT5e/6/7 cables

• HDBaseT™ Lite Receivers (e.g. CH-506RXL or CH-514RXL)

5. FEATURES

• HDMI with 4K×2K resolution and 3D support, HDCP and DVI

compliant

• Simultaneous HDMI and CAT5e/6/7 outputs

• Supports data rate from 300 Mbps up to 3 Gbps

• Supports a wide range of PC resolutions from VGA to WUXGA

(RB) and HDTV resolutions up to 4K×2K (3840×2160@30 Hz and

4096×2160@24 Hz)

• Supports transmission of High Denition audio: LPCM 7.1CH, Dolby

TrueHD, Dolby Digital Plus and DTS-HD Master Audio (32 kHz~192 kHz

sample rate)

• Supports distances up to 60 meters over CAT5e/6/7 cables

• Supports selection of Standard or TV EDID settings

• Supports control of devices via 2-way IR

• 3D signal display is dependent on the TV/Display’s EDID settings

Note:

1. This system was tested with CAT6/23AWG cables, results may vary

with cables of a different specication.

2. For playback of 4K×2K HDMI source signals, a 4K×2K capable

display and High Speed HDMI cables are required.

6. OPERATION CONTROLS AND FUNCTIONS

6.1 Front Panel

SYNC LINK EDID SERVICE

HDMI IN POWER

HDMI OUT

DC 24V

STDTV

1 2 3 4 5 6 7 8

1HDMI IN: Connect to HDMI equipped source equipment such as a

DVD/Blu-ray player or games console.

2SYNC LED: This LED will illuminate when the HDMI input is connected

to a HDMI source and receiving a signal.

3HDMI OUT: Connect to a HDMI display for local monitoring of the

HDMI signal or cascade to another Splitter.

4HDMI LINK LED: This LED will illuminate when HDMI output is

connected to TV or display monitor and receiving a signal.

5EDID STD/TV: The default setting is TV, when in this mode, the unit

will detect the EDID settings of the display device connected to

the CAT 5e/6/7 Output 1. If it detects a 4K×2K capable EDID setting

it will transmit the signal in that format to the output port. If no 4K×2K

capable EDID is detected then the unit will detect the EDID settings

and send out the signal that all outputs can accept.

This device has a last memory function and will retain the EDID

settings of the last device connected via the CAT5e/6/7 output

port when it is not connected to a display after power cycling.

Switch to the STD setting to use the unit's built-in EDID if there are

display problems. In this mode, the video output will be set to

1080p@60Hz and the audio at LPCM 2CH Stereo.

6SERVICE: Reserved for manufacture use only.

7POWER LED: The LED will illuminate when connected to an active

power supply.

8DC 24V: Connect the 24V DC power supply to the unit and plug

the adaptor into an AC outlet.

6.2 Rear Panel

MODE

LINK

MODE

LINK

MODE

LINK

IR IN IR OUT

CAT5e/6/7 OUT

1 2 3

1IR IN: Connect the supplied IR Receiver cable for IR signal

reception. Ensure that remote being used is within the direct line-

of-sight of the IR Extender.

2IR OUT: Connect the supplied IR Blaster cable for IR signal

transmission. Place the IR Blaster in direct line-of-sight of the

equipment to be controlled.

3CAT5e/6/7 OUT 1~3: Connect to CAT5e/6/7 to HDMI Receivers with

a single CAT5e/6/7 cable each to extend the HDMI signal up to

100 m.

MODE LED: This LED will illuminate when the power is connected.

LINK LED: This LED will illuminate when connected to a Receiver unit

that is connected with a TV/monitor that is displaying the signal.

6.3 IR Cable Pin Assignment

Power 3.3 V

IR Blaster Signal

IR Signal

Power 3.3 V

Grounding

IR Extender

IR Blaster

Inhaltsverzeichnis

Andere CYP Kabel und Steckverbinder Handbücher

CYP

CYP QU-4-4K22 Bedienungsanleitung

CYP

CYP CPRO-2E Bedienungsanleitung

CYP

CYP CMDP-13MDPI Bedienungsanleitung

CYP

CYP CLUX-18S Bedienungsanleitung

CYP

CYP DCT-28 Bedienungsanleitung

CYP

CYP CLUX-4EN Bedienungsanleitung

CYP

CYP CPRO-16E Bedienungsanleitung

CYP

CYP CPRO-16E Bedienungsanleitung

CYP

CYP CLUX-18E Bedienungsanleitung

CYP

CYP PUV-1H4HPL-AVLC Bedienungsanleitung

CYP

CYP PU-1H7HBTE Bedienungsanleitung

CYP

CYP CDP-13DPI Bedienungsanleitung

CYP

CYP CPLUS-V8E Bedienungsanleitung

CYP

CYP CPRO-U4T Bedienungsanleitung

CYP

CYP CPRO-8E Bedienungsanleitung

CYP

CYP CLUX-14EP Bedienungsanleitung

CYP

CYP CSDI-14 Bedienungsanleitung

CYP

CYP CPRO-U8T Bedienungsanleitung

CYP

CYP CPRO-2E Bedienungsanleitung

CYP

CYP QU-18WE Bedienungsanleitung

CYP

CYP Clux-8 Bedienungsanleitung

CYP

CYP CHDBT-1H4CPLV Bedienungsanleitung

CYP

CYP CPRO-2A Bedienungsanleitung

CYP

CYP HDBT CHDBT-1H7CL Bedienungsanleitung

Beliebte Kabel und Steckverbinder Handbücher anderer Marken

Philips

Philips SWA6310 Bedienungsanleitung

StarTech.com

StarTech.com CRJ4550PK Bedienungsanleitung

Nohau

Nohau EMUL-IP2K-PC Bedienungsanleitung

Foxun

Foxun SX-SP144E-HD4K2K Bedienungsanleitung

Philips

Philips SWA3305W Bedienungsanleitung

opticis

opticis Stretch DVIM1-1P0x Bedienungsanleitung

Volkswagen

Volkswagen VAS 6558A Bedienungsanleitung

NEXIBO

NEXIBO N-13 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-u2dhp Bedienungsanleitung

Global Caché

Global Caché Flex Link Blaster Bedienungsanleitung

Hauppauge

Hauppauge USB-Live2 Bedienungsanleitung

Fenix

Fenix MPSV 15 Bedienungsanleitung

BEGA

BEGA 71 085 Bedienungsanleitung

Tesla

Tesla HPWC Bedienungsanleitung

GAMERON

GAMERON LUXURY TV CABLE Bedienungsanleitung

molex

molex Milli-Grid Dual row 87568 Series Bedienungsanleitung

Burndy

Burndy Continental Industries thermOweld CRE-7 Bedienungsanleitung

Chauvet DJ

Chauvet DJ Data Stream 8 Bedienungsanleitung