CYP PU-O4H4C Bedienungsanleitung
OPERATION MANUAL
PU-O4H4C
v1.3 HDMI 4x4 Matrix with built
in HDMI over CAT6 outputs
Table of Contents
1. Introduction 1
2. Features 1
3. Package Contents 1
4. Operation Controls and Functions 2
4.1 Front Panel Diagram 2
4.2 Rear Panel Diagram 3
4.3 Remote Control 4-5
5. Pin Denitions 5-6
5.1 Commands 6
6. 3.5mm Connector Pin Denitions 5
6.1 IR IN Pin Denitions 7
6.2 IR OUT Pin Denitions 7
6.3 RJ-45 Pin Denitions 7
7. Connection Diagram 8
8. Specications 8-9
Page 1
1. Introduction
2. Features
•v1.3 HDMI, HDCP 1.1, DVI 1.0 compliant.
•HDMI 4x4 Matrix with built in HDMI over CAT6 transmitter outputs.
•Resolutions supported: PC - VGA to UXGA ; HDTV - 480i to 1080p + 1080p24fps
•
Master Audio + LPCM
•The HDMI input is compensated, clock / phase adjusted, and jitter eliminated
so the output is a brand new standard HDMI signal.
•Supports Deep Colour (10/12 bit).
•
•LED indicators
•Supports 3D signals
3. Package Contents
•4 by 4 HDMI V1.3 Matrix Infrared Repeater Box (CIR-12)
•Remote Control (with Battery)
•1 x IR Receiver.
All the PUMA, HDMI over CAT5e/6 transmitters and receivers are the perfect
solution to extend HDMI signals via CAT cabling up to 40m. The PU-O products
within the PUMA range combine HDMI over CAT5e/6 (PUMA) & HDMI Matrix
switcher (ORBIT) to provide versitility to HDMI installations. The PU-O4H4C HDMI
matrix has 4 HDMI input and 4 CAT transmitter outputs, designed to be used with
PU-1106RX receiver units. Each of the four HDMI sources can be directed to any
one of the four CAT outputs, so each display can show the same or a different
source.
Page 2
4. Operation Controls and Functions
4.1 Front Panel
1. Remote control sensor.
2. Power switch & LED Indicator: This LED will illuminate when the power is turned
on.
3. Input Select/Indicators (A/B/C/D): Press each “HDMI out” button repeatedly to
switch to your desired source. The LED that illuminates to indicate the input
source being selected and routed to HDMI A display.
4. HDCP indicators: This LED will illuminate once the input source being played
comes with a HDCP protection.
5. HDMI/DVI indicators: When the input is HDMI content, this LED will illuminate.
When playing DVI from the input source, this LED will not illuminate.
• 5 x IR Blaster
• 5V DC Power Supply Adaptor
• Power Cord
• Operation Manual
PU-O4H4C
HDMI V1.3 to CAT6 4X4 Matrix
POWER
IN
1 2 3 4
HDCP HDMI/DVI
1 2 3 4
HDCP HDMI/DVI
1 2 3 4
HDCP HDMI/DVI
1 2 3 4
HDCP HDMI/DVI
A BHDMI OUT C D
IN IN IN
1 2 3 4 5
Page 3
4.2 Rear Panel
1. EDID Control Switcher: Default factory setting is on TV, leave as it is when the
display is displaying properly. Switch to STD to use built-in EDID.
Note:
1. When EDID is switched to TV, the unit will detect the rst HDMI output source’s
EDID and record it in the unit. If the rst detected output source is DVI, it will
skip onto the next source until the rst HDMI source is detected. The detection
priority is HDMI v1.3 > HDMI v1.2 > DVI.
2. When EDID is switched to STD, the unit will use its built-in EDID that supports:
Video 1080p 12-bit (max) supports xvYCC Audio PCM 2CH
3. The EDID selection will only be activated after the unit is re-plugged and
powered on.
2. RS-232: This slot is where you connect a D-Sub 9-pin cable to the PC COM port
when controlling the device over RS-232. Detailed specications are listed in
section 9.
3. Video/DDC CAT 6 outputs: These slots are where you connect two CAT6 cables
to a receiver box that has HDMI output and through the HDMI output it can be
connect to TV. The receiver box can also be a splitter that provides additional
CAT6 outputs when cascading from a HDMI receiver to the display via HDMI
cable.
12 3 4 5 6 7 8
CAT6 OUTPUT
HDMI INPUT
IR OUT
STD TV DDC VIDEO
EDID
4 3 2 1
4 3 21
DC 5V
DDDC VIDEO
CDDC VIDEO
BDDC VIDEO
A
IN OUT
IR MAIN
RS-232
Page 4
4.3 Remote Control
1. Power: Press this button to turn on/off the unit.
1
2
3
4
5
4. IR OUT: These slots are where you connect with IR blaster cables included in
the package. Place it near each designate source equipment for infrared signal
sending.
5. HDMI inputs: These slots are where you connect input ports to the HDMI or DVI
output of your source equipments such as DVD player or set-topbox with HDMI
cables.
6. Power: Plug the 5VDC power supply into the unit and connect the adaptor to an
AC wall outlet.
7. IR MAIN IN: This slot is where you connect the IR receiver cable included in the
package. Connecting the IR receiver cable allows you to source equipments
through the existing remote controls.
8. IR MAIN OUT: This slot is where you connect the IR blaster cable included in the
package. Place it near both the device and/or source equipments for infrared
signal sending.
Page 5
2. Input Select for HDMI OUT A: Press 1, 2, 3 or 4 to select the desired input source
for HDMI OUT A.
3. Input Select for HDMI OUT B: Press 1, 2, 3 or 4 to select the desired input source
for HDMI OUT B.
4. Input Select for HDMI OUT C: Press 1, 2, 3 or 4 to select the desired input source
for HDMI OUT C.
5. Input Select for HDMI OUT D: Press 1, 2, 3 or 4 to select the desired input source
for HDMI OUT D.
PU-04H4C Remote Control Console
PIN Denitions PIN Denitions
1 NC 1NC
2 TxD 2 RxD
3 RxD 3TxD
4 NC 4 NC
5 GND 5 GND
6NC 6NC
7
NC
7
NC
8
NC
8
NC
9
NC
9
NC
5. Pin Denitions
* RS-232 transmission format:
Baud Rate: 9600bps
Data Bit: 8 bits
Page 6
COMMAND ACTION
POWER 00 Power Off (standby)
POWER 01 Power On
PORT 11 Output A select Input1
PORT 12 Output A select Input2
PORT 13 Output A select Input3
PORT 14 Output A select Input4
PORT 21 Output B select Input1
PORT 22 Output B select Input2
PORT 23 Output B select Input3
PORT 24 Output B select Input4
PORT 31 Output C select Input1
PORT 32 Output C select Input2
PORT 33 Output C select Input3
PORT 34 Output C select Input4
PORT 41 Output D select Input1
PORT 42 Output D select Input2
PORT 43 Output D select Input3
PORT 44 Output D select Input4
5.1 Commands
Parity: None
Stop Bit: 1 bit
Flow Control: None
Page 7
Pin Assignment
1 Power 5V
2 IR Signal
3 GND
Pin Assignment
1 IR Blaster Signal
2 Power 5V
3 IR Blaster Signal
Pin Video
DDC
1 TX2+ DDC Bus Clock
2 TX2- NC
3 TX1+ DDC Bus Data
4 TX0+ Power 5V
5 TX0- GND
6 TX1- IR IN
7 TXC+ HPD
8 TXC- NC
6. 3.5mm Connectors Pin Denitions
6.1 IR IN Pin Denitions
6.2 IR OUT Pin Denitions
6.3 RJ-45 Pin Denitions
Page 8
8. Specications
Frequency Bandwidth 2.25Gbps (single link)
EDID Standard, TV/Moving Port 1
ESD Protection Human body model: ± 10kV (air-gap di
charge) ± 6kV (contact discharge)
HDMI Audio Output PCM2, PCM5.1, PCM7.1, Dolby5.1, DTS5.1,
DD+, D-TrueHD, and DTS-HD
HDMI Cable In 1080p 8-bit (15M), 1080p 12-bit (15M)
HDMI Cable Out 1080p 8-bit (15M), 1080p 12-bit (15M)
CAT 6 Cable Out 1080p 8-bit (45M), 1080p 12-bit (15M)
Color Space RGB_24/36, YCbCr 4:4:4_24/36, YCbCr 4:2:2,
xvYCC
IR IN/OUT Yes/Yes
Deep Color 1080p 12-bit
HDMI Resolution 480i~1080p 50/60, 1080p 24, VGA~UXGA
7. Connection Diagram
Andere Handbücher für PU-O4H4C
1
Inhaltsverzeichnis
Andere CYP Matrix-Umschalter Handbücher
CYP
CYP OR-42-4K22 Bedienungsanleitung
CYP
CYP OR-DVI88SA Bedienungsanleitung
CYP
CYP CMSI-4H4CVL Bedienungsanleitung
CYP
CYP OR-HD88HC Bedienungsanleitung
CYP
CYP Elpro Video Labs CDPS-UC4H4HFS Bedienungsanleitung
CYP
CYP Elpro Video Labs CDPS-UC4H4HFS Installationshandbuch
CYP
CYP PUV-1082PL-4K22N Bedienungsanleitung
CYP
CYP PUV-662PL-4K22 Bedienungsanleitung
CYP
CYP CPLUS-V8H8HP Bedienungsanleitung
CYP
CYP CMSI-4H4CV Bedienungsanleitung
CYP
CYP HDBT PU-4H4HBTE-4K Bedienungsanleitung
CYP
CYP CPLUS-44PLV Bedienungsanleitung
CYP
CYP CMSI-8H8HC Bedienungsanleitung
CYP
CYP CMSI-4H4CV Bedienungsanleitung
CYP
CYP CPLUS-V4H4H Bedienungsanleitung
CYP
CYP CMPRO-UA8H8HS Bedienungsanleitung
CYP
CYP CDPS-UA6H2HFS Bedienungsanleitung
CYP
CYP PU-8H8HBTE Bedienungsanleitung
CYP
CYP CPLUS-662CVEA Bedienungsanleitung
CYP
CYP MOD-32 Bedienungsanleitung
