CYP CMPRO-UA8H8HS Bedienungsanleitung
CMPRO-UA8H8HS
8×8 HDMI 4K UHD Matrix
with HDCP 2.2
Operation Manual
Operation Manual
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2011 by Cypress Technology.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE (DD/MM/YY) SUMMARY OF CHANGE
RDV1 22/06/15 Preliminary release
CONTENTS
1. Introduction............................................ 1
2. Applications........................................... 1
3. Package Contents ................................ 1
4. System Requirements............................ 1
5. Features.................................................. 2
6. Operation Controls and Functions....... 3
6.1 Front Panel ........................................3
6.2 Rear Panel.........................................4
6.3 Side Panel .........................................5
6.4 Remote Control................................5
6.5 IR Cable Pin Assignment..................6
6.6 RS-232 Protocol.................................6
6.7 RS-232 and Telnet Commands .......7
6.8 Telnet Control ...................................8
6.9 WebGUI Control .............................10
7. Connection Diagram .......................... 13
8. Specications ...................................... 14
8.1 Technical Specications ...............14
8.2 Supported Resolutions...................15
9. Acronyms ............................................. 16
1
1. INTRODUCTION
The 8 by 8 HDMI 4K2K Matrix supports the transmission of video
(resolutions up to 4K2K Full HD & HDCP 2.2), multi-channel digital audio
and control via IR, RS-232, Telnet or WebGUI from eight high denition
sources to eight outputs.
It supports high resolution digital audio formats such as LPCM 7.1CH,
Dolby TrueHD, Dolby Digital Plus, Dolby Atmos and DTS-HD Master
Audio as well as 3D content that can be displayed when connecting
a 3D TV and 3D source.
2. APPLICATIONS
• HDMI Matrix System
• Video/TV wall display and control
• Security surveillance and control
• Commercial advertising, display and control
• University lecture hall, display and control
• Retail sales and demonstration
3. PACKAGE CONTENTS
• 1×8 by 8 HDMI 4K UHD Matrix
• 1×IR Extender
• 1×24 V/6.25A DC Power Adaptor
• 1×Remote control with battery
• 1×Power Cord
• 1×Ear rack
• 1×Operation Manual
4. SYSTEM REQUIREMENTS
• HDMI equipped source devices, connect with HDMI cables or DVI
equipped source, connect with DVI to HDMI cables
• HDMI equipped displays (TVs or monitors) or HDMI equipped AV
receivers, connect with HDMI cables
2
5. FEATURES
• HDMI with 4K2K supported, HDCP 2.2 and DVI compliant
• Supports PC resolution up to WUXGA and HDTV resolution up to
4K2K(3840x2160@24/25/30 & 3840x2160@50/60_YUV420, 4096x2160
@24/25/30 & 4096x2160 @50/60Hz _YUV420)
• Supports 3D signal bypass
• Supports pass-through audio LPCM 2/5.1/7.1CH, Dolby Digital
2~5.1CH, DTS 2~5.1CH, Dolby TrueHD and DTS-HD Master Audio
• Supports IR Extension
• Supports RS-232, remote control, on-panel control and IP control
(Telnet & WebGUI)
• 2U size design
• Compliant with DVI source
3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
POWER LOCK
MENU OUTA 1B2C3D4
IN
E5F6G7H8
2 3 4 5 61
1LCM:Displays the setting information of each input and output
setting.
2POWER: Press this button to power the device on/standby. The
LED will illuminate green when the power is on, red when it is in
'Standby' mode.
3LOCK: Press this button to lock all the buttons on the panel; press
again to unlock. The LED will illuminate green when locked.
4IR: IR Receiver window (accepts the remote control signal of this
device only).
5MENU: Press this button to access the LCM menu system, from
here EDID settings can be managed and IP system settings are
displayed.
61~8/A~H and OUT/IN: Press the OUT button and then the number
buttons to select the required output ports, and press IN button
and then a single number button to select the required input
source, nally press the MENU button to conrm the selection.
For example, if outputs A~D need to be set to input 1 and outputs
E~H need to be set to input 2 then the following sequence of
button presses need to be performed:
Press: OUTABCDIN1MENU,
and then press: OUTEFGHIN2MENU.
Note: If the MENU button is not pressed the selection will not be
changed.
4
6.2 Rear Panel
1
2
3
4
V+
GND
GND GND
V+
CONTROL
DC 24V
IR IN
RS 232 SERVICE
A
HDMI OUT
1
HDMI IN
B
HDMI OUT
2
HDMI IN
C
HDMI OUT
3
HDMI IN
D
HDMI OUT
4
HDMI IN
E
HDMI OUT
5
HDMI IN
F
HDMI OUT
6
HDMI IN
G
HDMI OUT
7
HDMI IN
H
HDMI OUT
8
HDMI IN
2 3 4 71 6
5
1CONTROL: This port is the link for Telnet and WebGUI controls, connect
to an active Ethernet link with an RJ45 terminated cable (for further
details, please refer to section 6.8 & 6.9).
Warning: Please do not connect this port directly to the PC/Laptop
as the Telnet function will not work.
2RS-232: Connect to a PC or control system with D-sub 9-pin cable
for the transmission of RS-232 commands.
3IR IN: Connect to the supplied IR extenders for IR signal reception
from the remote control of the Matrix. Ensure that the remote is
within the direct line-of-sight of the IR extender when used.
4SERVICE: Manufacturer use only.
5HDMI OUT A~H: Connect to HDMI equipped TVs or monitors for
display of the HDMI input source signal.
6HDMI IN 1~8: Connect to the HDMI input source devices such as a
DVD player or a Set-top Box with HDMI cable or DVI to HDMI cable..
7DC 24V: Plug the 24 V DC power supply into the unit and connect
the adaptor to an AC outlet.
5
6.3 Side Panel
1
1Fan Ventilator: These are air ventilation areas, DO NOT block these
areas or cover it with any object. Please allow adequate space
around the unit for air circulation.
6.4 Remote Control
1POWER: Press this button to switch on the
device or set it to standby mode.
2IN: Input ports selection 1~8.
3OUT: Output ports selection A~H.
1
23
6
6.5 IR Cable Pin Assignment
3
1
2
3
2
1
IR Signal
Power
Grounding
IR Extender
6.6 RS-232 Protocol
MATRIX
►
◄
REMOTE CONTROLLER
Pin Assignment Pin Assignment
1 NC 1 NC
2Tx 2Rx
3Rx 3Tx
4 NC 4 NC
5 GND 5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
Baud Rate: 115200bps
Data bit: 8 bits
Parity: None
Flow Control: None
Stop Bit: 1
Inhaltsverzeichnis
Andere CYP Matrix-Umschalter Handbücher
CYP
CYP CMPRO-U4H4CVPL Bedienungsanleitung
CYP
CYP CDPS-44SM Bedienungsanleitung
CYP
CYP PUV-1210PL-RX Bedienungsanleitung
CYP
CYP PU-16HBT Bedienungsanleitung
CYP
CYP PUV-44XPL-AVLC Bedienungsanleitung
CYP
CYP nT15GX01 Bedienungsanleitung
CYP
CYP PU-8H8HBTPL Bedienungsanleitung
CYP
CYP CMPRO-U4H4CVE Bedienungsanleitung
CYP
CYP CMSI-8H8HS Bedienungsanleitung
CYP
CYP CMSI-3232 Bedienungsanleitung
CYP
CYP PUV-442-4K22 Bedienungsanleitung
CYP
CYP OR-HD44E Bedienungsanleitung
CYP
CYP OR-HD24S Bedienungsanleitung
CYP
CYP PU-8H8HBTE Bedienungsanleitung
CYP
CYP MOD-16 Bedienungsanleitung
CYP
CYP CPLUS-V4H2HPIP Bedienungsanleitung
CYP
CYP Elpro Video Labs CDPS-UC4H4HFS Bedienungsanleitung
CYP
CYP CDPS-44SM Bedienungsanleitung
CYP
CYP nT17BX19 Bedienungsanleitung
CYP
CYP CMSI-46PL Bedienungsanleitung
