CYP CMSI-4H4CV Bedienungsanleitung

DRAFT

CMSI-4H4CV/CMSI-8H8CV

HDBaseT™ 4×4/8×8 HDMI Matrix over CAT5e/6/7

Operation Manual

DRAFT

DISCLAIMERS

The information in this manual has been carefully checked and

is believed to be accurate. Cypress Technology assumes no

responsibility for any infringements of patents or other rights of third

parties which may result from its use.

Cypress Technology assumes no responsibility for any inaccuracies

that may be contained in this document. Cypress also makes no

commitment to update or to keep current the information contained

in this document.

Cypress Technology reserves the right to make improvements to this

document and/or product at any time and without notice.

No part of this document may be reproduced, transmitted,

transcribed, stored in a retrieval system, or any of its part translated

into any language or computer le, in any form or by any means—

electronic, mechanical, magnetic, optical, chemical, manual, or

otherwise—without express written permission and consent from

Cypress Technology.

Version 1.1 August 2011

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be

trademarks of the companies with which they are associated.

DRAFT

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or

operate this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

• Always follow basic safety precautions to reduce the risk of re,

electrical shock and injury to persons.

• To prevent re or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts

inside the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the PSU

if it is damaged.

• Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow for

sufcient space for air to circulate around the unit.

REVISION HISTORY

VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE

RDV1 07/09/11 Preliminary Release

RDV2 15/02/12 Corrections

VS0 02/04/12 Updated format, diagrams, and

statements

RDV3 04/06/12 CAT5e/6's Warning

RDV4 15/06/12 Add 4H4CV, Telnet & GUI

RDV5 10/07/12 Connection Diagram

VS0 23/07/12 Telnet and Web GUI sections

updated

DRAFT

CONTENTS

1. Introduction............................................ 1

2. Applications........................................... 1

3. Package Contents ................................ 1

4. System Requirements............................ 2

5. Features.................................................. 2

6. Operation Controls and Functions....... 3

6.1 Front Panel ........................................3

6.2 Rear Panel.........................................4

6.3 Side Panel .........................................5

6.4 Remote Control................................5

6.5 IR Cable Pin Assignment..................6

6.6 RS-232 Pin Assignment .....................7

6.7 RS-232 and Telnet Commands .......8

6.8 Telnet Control ...................................9

7. Connection Diagram .......................... 11

8. Specications ...................................... 13

9. Acronyms ............................................. 14

DRAFT

1. INTRODUCTION

The HDBaseT™ 4 by 4 or 8 by 8 HDMI Matrix over CAT5e/6/7 supports

the transmission of video (resolutions up to 1080p Full HD and

1920x1200@60Hz), multi-channel digital audio and control via IR, RS-

232 or Telnet from four or eight high denition sources to four or eight

outputs over a single CAT5e/6/7 cable (up to 100m) for each output.

It supports high resolution digital audio formats such as LPCM 7.1CH,

Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio as well as

3D content that can be displayed when connecting a 3DTV and 3D

source. Power over Ethernet (PoE) support means that compatible

receivers do not need their own power supplies, allowing for greater

exibility in installations.

2. APPLICATIONS

• Domestic HDMI Matrix System

• Video/TV wall display and control

• Security surveillance and control

• Commercial advertising, display and control

• University lecture hall, display and control

• Retail sales and demonstration

3. PACKAGE CONTENTS

• HDBaseT™ 4×4/8×8 HDMI Matrix over CAT5e/6/7

• 2×IR Extender

• 2×IR Blaster

• 2×24 V/6.25 A DC Power Adaptor (1 for PoE)

• 1×IR Remote Control

• Operation Manual

DRAFT

4. SYSTEM REQUIREMENTS

• HDMI equipped source devices, connect with HDMI cables or DVI

equipped source, connect with DVI to HDMI cables

• HDMI equipped displays (TVs or monitors) or HDMI equipped AV

receivers, connect with HDMI cables

• Industry standard CAT5e/6/7 cables

• HDBaseT™ Receivers (i.e. CH-506RX, CH-507RX or CH-1109RX)

5. FEATURES

• HDMI, HDCP1.1 and DVI compliant

• Supports HDMI 3D features

• Supports resolutions VGA~WUXGA and 480i~1080p dependent upon

the output display’s EDID settings

• Supports distances up to 100 meters through CAT6/7 cables and

80m for CAT5e

• Supports 3D signal display dependent upon the output display EDID

settings

• Supports PoE (Power over Ethernet) on compatible receivers only

• Supports HDMI input up to 15 meters at 8-bit resolution or 10 meters

at 12-bit resolution

• Supports bi-directional IR from input and output locations

• Supports RS-232, remote control, on-panel control and IP Control

(Telnet)

• 2U size design

• Supports external and internal EDID settings

• Supports LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD

Master Audio transmission

Note:

1. The PoE function is designed for powering compatible receiver units

only—non-PoE receivers will need their own power supply. Receivers

of another brand may not be compatible.

2. Do not connect the LAN/CONTROL port to CAT outputs of this

device.

DRAFT

6. OPERATION CONTROLS AND FUNCTIONS

6.1 Front Panel

POWER LOCK

MENU OUTA 1B2C3D4

E5F6G7H8

8X8 HDMI MATRIX over CAT5e/6 CMSI-8H8CV

2 3 4 5 61

1LCM: Displays the setting information of each input and output

setting.

2POWER: Press this button to power the device on/off. The LED will

illuminate green when the power is on, red when it is in 'Standby'

mode.

3LOCK: Press this button to lock all the buttons on the panel; press

again to unlock. The LED will illuminate green when locked.

IR: IR Receiver window (accepts the remote control signal of this

device only).

MENU: Press this button to access the LCM menu system, from

here EDID settings can be managed and IP system settings are

displayed.

1~8/A~H and OUT/IN: Press the OUT or IN button to select the

output or input mode and then press the required number button

to make the selection accordingly.

For example, if outputs A~D need to be set to input 1 and outputs

E~H need to be set to input 2, then the following sequence of

button presses need to be performed:

Press: OUTABCDIN1MENU,

and then press: OUTEFGHIN2MENU.

Note: If the MENU button is not pressed the selection will not be

changed.

DRAFT

6.2 Rear Panel

CONTROL

RS232

SERVICE

IR OUT

IR IN

IR OUT

IR IN

IR OUT

IR IN

ALL A B C D E F G H

CAT5e/6 OUT

IR OUT

IR IN

CAT5e/6 OUT

IR OUT

IR IN

CAT5e/6 OUT

IR OUT

IR IN

CAT5e/6 OUT

IR OUT

IR IN

CAT5e/6 OUT

IR OUT

IR IN

CAT5e/6 OUTCAT5e/6 OUT

IR OUT

IR IN

CAT5e/6 OUT

MAIN 24V

POE 24V

HDMI IN

V+

GND

GND GND

V+

510 111

CONTROL: This port is the link for Telnet control, connect to an active

Ethernet link with an RJ45 terminated cable (for further details, please

refer to section 6.8).

Warning: Please do not connect this port directly to the PC/Laptop as the

Telnet function will not work.

2RS-232: Connect to a PC or control system with D-Sub 9-pin cable

for the transmission of RS-232 commands.

3ALL IR OUT: Connect to the IR blaster for IR signal transmission of the

source or display equipment. Place the IR blaster in direct line-of-

sight of the equipment to be controlled.

4ALL IR IN: Connect to the R extender for IR signal reception of the

remote control of this device or the source and display equipment.

Ensure that remote being used is within the direct line-of-sight of

the IR extender.

SERVICE: Manufacturer use only.

IR OUT A~H: Connect to the IR blasters for IR signal transmission.

Place the IR blaster in direct line-of-sight of the equipment to be

controlled.

IR IN 1~8: Connect to the IR extenders for IR signal reception. Ensure

that the remote being used is within the direct line-of-sight of the IR

extender.

CAT5e/6/7 OUT A~H: Connect from these CAT outputs to the CAT

input port of the receiver units with a single CAT5e/6/7 cable for HDMI

Audio/Video and IR/RS-232 control signal transmission.

HDMI IN 1~8: Connect to the HDMI input source devices such as a

DVD player or a Set-top Box with HDMI cable or DVI to HDMI cable.

DC 24V: Plug the 24 V DC power supply into the unit and connect the

adaptor to an AC outlet.

PoE 24V: Plug the 24 V PoE power supply into the unit and connect

the adaptor to an AC outlet. This unit will mainly power PoE (Power

over Ethernet) capaable receiver units.

DRAFT

Warning: Please do not connect the CAT5e/6/7 cable into the

receiver's LAN port.

6.3 Side Panel

1Fan Ventilator: These are air ventilation areas, DO NOT block these

areas or cover it with any object. Please allow adequate space

around the unit for air circulation.

6.4 Remote Control

1POWER: Press this button to

switch on the device or set it to

standby mode.

IN: Input ports selection 1~8.

3OUT: Output ports selection A~H.

Andere Handbücher für CMSI-4H4CV

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CYP Matrix-Umschalter Handbücher

CYP

CYP CMSI-8D8DS Bedienungsanleitung

CYP

CYP PU-8H8HBTE Bedienungsanleitung

CYP

CYP PUV-662PL-4K22 Bedienungsanleitung

CYP

CYP OR-42-4K22 Bedienungsanleitung

CYP

CYP CDPS-44SM Bedienungsanleitung

CYP

CYP CPLUS-V4H2HP Bedienungsanleitung

CYP

CYP PUV-1210PL-RX Bedienungsanleitung

CYP

CYP CMSI-8H8CV Bedienungsanleitung

CYP

CYP OR-42SA-4K22 Bedienungsanleitung

CYP

CYP PU-16H8HBT Bedienungsanleitung

CYP

CYP CMSDI-1616S Bedienungsanleitung

CYP

CYP MOD-32 Bedienungsanleitung

CYP

CYP OR-IR44 Bedienungsanleitung

CYP

CYP OR-HD24S Bedienungsanleitung

CYP

CYP PUV-442-4K22 Bedienungsanleitung

CYP

CYP MA-421 Bedienungsanleitung

CYP

CYP PUV-1082-PRO Bedienungsanleitung

CYP

CYP CMPRO-U8H8CVE Bedienungsanleitung

CYP

CYP CMPRO-U4H4CVE Bedienungsanleitung

CYP

CYP SM-4X4-HDMI-LC Bedienungsanleitung

CYP

CYP CMSI-4H4CVL Bedienungsanleitung

CYP

CYP CPLUS-V4H2HA Bedienungsanleitung

CYP

CYP CMPRO-4H4H Bedienungsanleitung

CYP

CYP CDPS-4H4HFS Bedienungsanleitung

Beliebte Matrix-Umschalter Handbücher anderer Marken

Broadcast Tools

Broadcast Tools SS 8.2 Bedienungsanleitung

Altimium

Altimium MATF32 Bedienungsanleitung

ALFAtron

ALFAtron ALF-MUK44N Bedienungsanleitung

Monoprice

Monoprice Blackbird 15377 Bedienungsanleitung

Kramer

Kramer XL 3216VS Bedienungsanleitung

PTN

PTN FMX12 Bedienungsanleitung

Kramer

Kramer VP-2x2 Bedienungsanleitung

Kramer

Kramer Sierra Video 6432V5xl Bedienungsanleitung

TESmart

TESmart HMA0402A40 Bedienungsanleitung

Octava

Octava HD4XSTPMX Bedienungsanleitung

Intelix

Intelix FLX-88 Betriebsanleitung

Kramer

Kramer LASSEN XL 3232S Bedienungsanleitung

Roland

Roland XS-1HD Bedienungsanleitung

Kramer

Kramer VS-66HDCPxl Bedienungsanleitung

Atlona

Atlona AT-HDMI-22M Bedienungsanleitung

Link

Link HD8X8 Bedienungsanleitung

AMX

AMX AVS-OP-2020-117 Anleitungen und Rezepte

Lindy

Lindy 38042 Bedienungsanleitung