CYP RXWPBD Bedienungsanleitung
CH-507TXWPBD & RXWPBD
HDMI over Single CAT5e/6/7
Wall-plate Transmitter and Receiver
Operation Manual
Operation Manual
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2011 by Cypress Technology.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE
RDV1 25/04/13 Preliminary Release
VS0 21/03/14 Updated text/diagrams
CONTENTS
1. Introduction............................................ 1
2. Applications........................................... 1
3. Package Contents ................................ 1
4. System Requirements............................ 1
5. Features.................................................. 2
6. Operation Controls and Functions....... 3
6.1 Transmitter Front and Rear Panels..3
6.2 Receiver Front and Rear Panels .....4
6.3 IR Cable Pin Assignment..................6
6.4 RS-232 Cable Pin Denitions............6
7. Connection Diagrams........................... 7
7.1 Option 1: Point to Point....................7
7.2 Option 2: Matrix System...................8
8. Specications ........................................ 9
8.1 Technical Specications .................9
8.2 CAT5e/6/7 Cable Specications..10
9. Acronyms ............................................. 10
1
1. INTRODUCTION
The HDMI over Single CAT5e/6/7 Wall-plate Transmitter and Receiver
set can send uncompressed video/audio and IP data over a single
run of CAT5e/6/7 cable up to 100 meters. It has the added benet of
control through the built-in RS-232 pass-through and 2-way IR control
and a LAN serving connection. Additionally, it has bi-directional Power
over Ethernet (PoE) functionality that allows for greater exibility in
installations.
2. APPLICATIONS
• Household entertainment sharing and control
• Lecture room display and control
• Showroom display and control
• Meeting room presentation and control
• Classroom display and control
3. PACKAGE CONTENTS
• HDMI over Single CAT5e/6/7 Transmitter
• HDMI over Single CAT5e/6/7 Receiver
• IR Blaster
• IR Extender
• 24 V/1.25 A DC Power Adaptor
• Operation Manual
4. SYSTEM REQUIREMENTS
HDMI source device such as a DVD/Blu-ray player and an HDMI
equipped display (TV or monitor).
2
5. FEATURES
• HDMI (with 3D format and 4K2K resolution support), HDCP and DVI
compliant
• Supports HDCP repeater and CEC bypass functions
• Simultaneous transmission of uncompressed video/audio and data
over a single CAT5e/6/7 cable up to 100m/328ft
• HDBaseT™ 5Play convergence: uncompressed high-denition Video
and Audio, LAN serving, bi-directional Power over Ethernet (PoE)
and IR/RS-232 Control pass-through
• Supports uncompressed video up to 4K2K resolution
(3840×2160@30 Hz or 4096×2160@24 Hz)
• Supports pass-through of high-denition audio formats - LPCM 7.1CH,
Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio
• Wall-plate design and installation friendly
Note:
1. This system was tested with CAT6/23AWG and CAT5e/24AWG
cables, results may vary with cables of a different specication.
2. The PoE function is designed for powering compatible Transmitter
and Receiver units only—non-PoE units will need their own power
supply. Transmitters/Receivers from other brands may not be
compatible.
3. For playback of 4K×2K HDMI source signals, a 4K×2K capable
display and High Speed HDMI cables are required.
3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Transmitter Front and Rear Panels
HDMI INLAN
POWER
LINK
IR 2
EXTENDER
IR 1
BLASTER
DC 24V
RS-232
IN
1 2 3 4 5 6 7 8 9
1IR 2 EXTENDER: Connect an IR Extender cable for IR signal
reception. Signals received will be transmitted from any IR blaster
connected to the receiver unit. Ensure that the remote being used
is within the direct line-of-sight of the IR Extender.
2IR 1 BLASTER: Connect an IR Blaster cable for IR signal transmission.
IR signals received by an IR extender connected to the receiver
unit will be transmitted by this blaster. Place the IR Blaster in direct
line-of-sight of the equipment to be controlled.
3RS-232 IN: Connect to a PC or laptop with D-sub 9-pin male cable
for the transmission of RS-232 commands.
4LAN: Connect to an active network for LAN serving and Telnet/
Web GUI control.
When the transmitter or any compatible LAN equipped receivers
are connected to a network, this allows the network access
(including internet access if available) to be shared between the
transmitter and all connected receivers. Connect any Ethernet
equipped device e.g. a Smart TV or games console to the LAN
port of a receiver for that device to share the network/internet
access.
5DC 24V: Connect the 24 V DC power supply to the transmitter and
plug the adaptor into an AC outlet.
6HDMI IN: Connect to HDMI source equipment such as a DVD or
Blu-ray player.
7POWER LED: This LED will illuminate when the transmitter is
4
connected to a power supply or powered by another unit via PoE.
8LINK LED: This LED will illuminate when both the source connected
to the transmitter and the display connected to the receiver are
connected.
9CAT5e/6/7 OUT: Connect to the receiver unit with a single
CAT5e/6/7 cable for transmission of all data signals.
6.2 Receiver Front and Rear Panels
HDMI OUTLAN
POWER
LINK
IR 1
EXTENDER
IR 2
BLASTER
DC 24V
RS-232
OUT
1 2 3 4 5 6 7 8 9
1IR 1 EXTENDER: Connect an IR Extender cable for IR signal
reception. Signals received will be transmitted from any IR blaster
connected to the transmitter unit. Ensure that the remote being
used is within the direct line-of-sight of the IR Extender.
2IR 2 BLASTER: Connect an IR Blaster cable for IR signal transmission.
IR signals received by an IR extender connected to the transmitter
unit will be transmitted by this blaster. Place the IR Blaster in direct
line-of-sight of the equipment to be controlled.
3RS-232 OUT: Connect to the device that is to be controlled (via
D-sub 9-pin female cable) by RS-232 commands.
4LAN: Connect to an active network for LAN serving and Telnet/
Web GUI control.
When the transmitter or any compatible LAN equipped receivers
are connected to a network, this allows the network access
(including internet access if available) to be shared between the
transmitter and all connected receivers. Connect any Ethernet
equipped device e.g. a Smart TV or games console to the LAN
port of a receiver for that device to share the network/internet
access.
5
5DC 24V: Connect the 24 V DC power supply to the transmitter and
Plug the adaptor into an AC outlet.
6HDMI OUT: Connect to a HDMI equipped TV/monitor for display of
the HDMI input source signal.
7POWER LED: This LED will illuminate when the receiver is connected
to a power supply or powered by another unit via PoE.
8LINK LED: This LED will illuminate when both the source connected
to the transmitter and the display connected to the receiver are
connected.
9CAT5e/6/7 IN: Connect to the transmitter unit with a single
CAT5e/6/7 cable for transmission of all data signals.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere CYP Empfänger Handbücher
CYP
CYP CA-USBST Bedienungsanleitung
CYP
CYP PU-515PLRX-2HCD Bedienungsanleitung
CYP
CYP PUV-3050RX-UA Bedienungsanleitung
CYP
CYP CA-HDMI150R Bedienungsanleitung
CYP
CYP PUV-1650TX Bedienungsanleitung
CYP
CYP PUV-2100RX-AVLC Bedienungsanleitung
CYP
CYP PU-515PL-WPRX Bedienungsanleitung
CYP
CYP CH-352RX Bedienungsanleitung
CYP
CYP CA-HDMI100R Bedienungsanleitung
CYP
CYP CH-507TX Bedienungsanleitung
CYP
CYP DCT-30RX Bedienungsanleitung
CYP
CYP CWHDI-TX1 Bedienungsanleitung
CYP
CYP PU-607BD-RX Bedienungsanleitung
CYP
CYP PU-607BD-RX Bedienungsanleitung
CYP
CYP PUV-1830RX-AVLC Bedienungsanleitung
CYP
CYP CPLUS-21FRX Bedienungsanleitung
CYP
CYP CH-514RXWPL Bedienungsanleitung
CYP
CYP 5-Play HDBaseT PU-507WPRX Bedienungsanleitung
CYP
CYP CH-A320RX Bedienungsanleitung
CYP
CYP PUV-1810RX-AVLC Bedienungsanleitung
