Cypress Semiconductor FM0+ S6E1C Series Bedienungsanleitung

FM0+ S6E1C-Series

Starter Kit Guide

Doc. # 002-10542 Rev. *D

Cypress Semiconductor

198 Champion Court

San Jose, CA 95134-1709

www.cypress.com

Downloaded from Arrow.com.

FM0+ S6E1C-Series Starter Kit Guide, Doc. # 002-10542 Rev. *D 2

Copyrights

and its subsidiaries, including Spansion LLC (“Cypress”). This document, including any software or firmware included or

referenced in this document (“Software”), is owned by Cypress under the intellectual property laws and treaties of the United

States and other countries worldwide. Cypress reserves all rights under such laws and treaties and does not, except as

specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual

property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written

agreement with Cypress governing the use of the Software, then Cypress hereby grants you under its copyright rights in the

Software, a personal, non-exclusive, nontransferable license (without the right to sublicense) (a) for Software provided in

source code form, to modify and reproduce the Software solely for use with Cypress hardware products, only internally

within your organization, and (b) to distribute the Software in binary code form externally to end users (either directly or

indirectly through resellers and distributors), solely for use on Cypress hardware product units. Cypress also grants you a

personal, non-exclusive, nontransferable, license (without the right to sublicense) under those claims of Cypress’s patents

that are infringed by the Software (as provided by Cypress, unmodified) to make, use, distribute, and import the Software

solely to the minimum extent that is necessary for you to exercise your rights under the copyright license granted in the

previous sentence. Any other use, reproduction, modification, translation, or compilation of the Software is prohibited.

CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR

ANY SOFTWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes to this document without further

notice. Cypress does not assume any liability arising out of the application or use of any product or circuit described in this

document. Any information provided in this document, including any sample design information or programming code, is

provided only for reference purposes. It is the responsibility of the user of this document to properly design, program, and

test the functionality and safety of any application made of this information and any resulting product. Cypress products are

not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of

weapons, weapons systems, nuclear installations, life-support devices or systems, other medical devices or systems

(including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other

uses where the failure of the device or system could cause personal injury, death, or property damage (“Unintended Uses”).

A critical component is any component of a device or system whose failure to perform can be reasonably expected to cause

the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and

Company shall and hereby does release Cypress from any claim, damage, or other liability arising from or related to all

Unintended Uses of Cypress products. Company shall indemnify and hold Cypress harmless from and against all claims,

costs, damages, and other liabilities, including claims for personal injury or death, arising from or related to any Unintended

Uses of Cypress products.

Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB,

F-RAM, and Traveo are trademarks or registered trademarks of Cypress in the United States and other countries. For a

more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their

respective owners.

Downloaded from Arrow.com.Downloaded from Arrow.com.

FM0+ S6E1C-Series Starter Kit Guide, Doc. # 002-10542 Rev. *D 3

Contents

1. Introduction....................................................................................................................................................................4

1.1 Kit Contents...........................................................................................................................................................4

1.2 Board Details.........................................................................................................................................................5

1.3 Jumper and Connector..........................................................................................................................................7

1.4 Getting Started ......................................................................................................................................................7

1.5 Additional Learning Resources..............................................................................................................................8

1.6 Technical Support..................................................................................................................................................8

1.7 Acronyms ..............................................................................................................................................................8

2. Installation and Test Operation....................................................................................................................................9

2.1 Install Software......................................................................................................................................................9

2.2 Un-install Software ..............................................................................................................................................12

2.3 Test Operation.....................................................................................................................................................13

3. Hardware......................................................................................................................................................................18

3.1 System Block Diagram........................................................................................................................................18

3.2 Hardware Features..............................................................................................................................................18

3.3 Hardware Details.................................................................................................................................................19

4. Software Development................................................................................................................................................29

4.1 Tool Options........................................................................................................................................................29

4.2 Example Projects.................................................................................................................................................32

4.3 Flash Programming.............................................................................................................................................44

A. Appendix......................................................................................................................................................................49

A.1 Schematic............................................................................................................................................................49

A.2 Bill of Materials....................................................................................................................................................53

Revision History...................................................................................................................................................................56

Document Revision History ...........................................................................................................................................56

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

FM0+ S6E1C-Series Starter Kit Guide, Doc. # 002-10542 Rev. *D 4

1. Introduction

Thank you for your interest in the FM0+ S6E1C-Series Starter Kit. This kit enables customers to

evaluate and develop projects using the FM0+ device family. FM0+ is a portfolio of ultra-low

power ARM® Cortex®-M0+ MCUs. It is designed for low-power and cost-sensitive applications

such as white goods, sensors, meters, HMI systems, power tools and internet of things (IoT)

battery powered or energy harvesting wearable devices. There are several device series in this

portfolio: the S6E1A-Series, the S6E1B-Series and the S6E1C-Series. This kit uses a device

from the S6E1C-Series.

The S6E1C-Series microcontroller is based on the ARM® Cortex®-M0+ processor with on-chip

flash memory. This series has peripherals such as High Definition Multimedia

Interface-Consumer Electronics Control (HDMI-CEC), A/D converters, Descriptor System Data

Transfer Controller (DTSC) and communication interfaces like USB, UART, CSIO (SPI), I2C and

LIN. The FM0+S6E1C-Series Starter Kit offers footprint compatibility with Arduino™ shields,

which provides options for application development.

1.1 Kit Contents

The FM0+ S6E1C-Series Starter Kit contains the following, as shown in Figure 1-1.

FM0+ S6E1C-Series board

USB Standard-A to Micro-B cable

Quick Start Guide

Figure 1-1: Kit Contents

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Introduction

FM0+ S6E1C-Series Starter Kit Guide, Doc. # 002-10542 Rev. *D 5

Inspect the contents of the kit; if you find any part missing, contact your nearest Cypress sales

office for help: www.cypress.com/support.

1.2 Board Details

Figure 1-2: FM0+ S6E1C-Series Starter Kit Markup

1. Arduino Interface (CN7-CN10)

2. User button

3. MB9AF312K programmer and debugger (CMSIS-DAP)

4. Serial programming mode select (J3)

5. Power supply resource select (J4)

6. USB device connector (CN4)

7. Potentiometer

8. MB9AF312K programming mode jumper (J1)

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Introduction

FM0+ S6E1C-Series Starter Kit Guide, Doc. # 002-10542 Rev. *D 6

9. Headphone and microphone jack (CN1)

10. Reset button

11. Multicon connector (CN12, CN13)

12. Jumper for current measurement (J5)

13. 10-pin JTAG connector

14. Stereo codec

15. Programming mode jumper (J2)

16. Cypress FM0+ MCU S6E1C32D0A

17. RGB LED

18. NOR flash

19. 3.3 V voltage regulator

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Introduction

FM0+ S6E1C-Series Starter Kit Guide, Doc. # 002-10542 Rev. *D 7

1.3 Jumper and Connector

Table 1-1: Jumper Description

Jumper

Function

Setting

Sets the programming mode pin (MD0) of

MB9AF312K (CMSIS-DAP)

Open: run mode

Closed: serial programming mode

Sets the programming mode pin (MD0) of

S6E1C3

Open: run mode

Closed: serial programming mode

Serial programming mode Select for

S6E1C3

Pin 2 to Pin 1: UART programming mode (not supported on this

kit)

Pin 2 to Pin 3: USB programming mode

Power supply resource select

Pin 2 to Pin 1: power from CMSIS-DAP (CN3)

Pin 2 to Pin 3: power from USB port of S6E1C3 (CN4)

Jumper for power measurement

Open jp11 and connect a multi-meter with the terminals of J5 to

measure the current that FM0+ MCU consumes.

Table 1-2: Connector Description

Connector

Description

CN1

Headphone and microphone jack

CN2

10-pin JTAG interface

CN3

USB port of CMSIS-DAP

CN4

USB port of FM0+ MCU

CN7,CN8,CN9,CN10

Arduino compatible headers

CN12,CN13

Multicon connector

1.4 Getting Started

This guide will help you get started with the FM0+S6E1C-Series Starter Kit:

The Installation and Test Operation chapter describes the installation of the kit installer,

and the test procedures for testing the board.

The Hardware chapter describes the major features of the FM0+ S6E1C-Series Starter

Kit and functionalities such as CMSIS-DAP debugger, Ethernet, USB, stereo codec,

memories and sensors.

The Software Development chapter describes how to open and run an example project

in the IAR Embedded Workbench or Keil µVision IDE; it also describes how to use the

example projects and how to program the devices using the USB DIRECT Programmer.

The Appendix provides the kit schematics, and the bill of materials (BOM).

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Introduction

FM0+ S6E1C-Series Starter Kit Guide, Doc. # 002-10542 Rev. *D 8

1.5 Additional Learning Resources

Cypress provides a wealth of data at www.cypress.com to help you to select the right MCU device

for your design, and to quickly and effectively integrate the device into your design.

Visit the FM0+ product page for links to multiple resources, such as:

Microcontroller Selector Guide

Getting Started information

Datasheets

FM0+ Peripheral Manuals

1.6 Technical Support

For assistance, visit Cypress Support or contact customer support at +1(800) 541-4736 Ext. 2

(in the USA) or +1 (408) 943-2600 Ext. 2 (International).

1.7 Acronyms

Table 1-3. Acronyms Used in this Document

Acronym

Description

ADC

Analog-to-Digital Converter

CMSIS-DAP

Debug Access Port

DTSC

Descriptor System Data Transfer Controller

GPIO

General Purpose Input/output

HDMI-CEC

HighDefinition Multimedia Interface-Consumer Electronics Control

IDE

Integrated Development Environment

I2C

Inter-Integrated Circuit

I2S

Inter-IC Sound

JTAG

Joint Test Action Group

LDO

Low Drop Out (voltage regulator)

LED

Light-Emitting Diode

PDL

Peripheral Driver Library

PWM

Pulse Width Modulation

RGB

Red Green Blue

SWD

Serial Wire Debug

SPI

Serial Peripheral Interface

UART

Universal Asynchronous Receiver Transmitter

USB

Universal Serial Bus

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

FM0+ S6E1C-Series Starter Kit Guide, Doc. # 002-10542 Rev. *D 9

2. Installation and Test Operation

This chapter describes the steps to install the software tools and drivers on a PC for using the

FM0+ S6E1C-Series Starter Kit. After a successful installation, user can run the test code which

is pre-programmed in the device.

2.1 Install Software

Follow the steps below to install the FM0+ S6E1C-Series Starter Kit software:

1. Download the FM0+ S6E1C-Series Starter Kit installer from the webpage:

www.cypress.com/FM0-64L-S6E1C3.The Kit software is available for download in three

formats.

FM0+ S6E1C-Series Starter Kit Complete Setup: This installation package contains

the files related to the kit, including the Documentation, Hardware, Firmware, Software

tools and drivers. However, it does not include the Windows Installer or Microsoft .NET

framework packages. If these packages are not on your computer, the installer directs

you to download and install them from the Internet.

FM0+ S6E1C-Series Starter Kit Only Package: This executable file installs only the kit

contents, which include kit code examples, hardware files, and user documents. This

package can be used if all the software prerequisites (listed in step 5) are installed on

your PC.

FM0+ S6E1C-Series Starter Kit DVD ISO: This file is a complete package, stored in a

DVD-ROM image format, which you can use to create a DVD or extract using an ISO

extraction program such as WinZip® or WinRAR. The file can also be mounted like a

virtual CD/DVD using virtual drive programs such as Virtual CloneDrive and MagicISO.

This file includes all the required software, utilities, drivers, hardware files, and user

documents.

2. If you have downloaded the ISO file, mount it in a virtual drive. Extract the ISO contents if

you do not have a virtual drive to mount. Double-click cyautorun.exe in the root directory of

the extracted content or the mounted ISO if “Autorun from CD/DVD” is not enabled on the

PC. The installation window will appear automatically.

Note: If you are using the “Kit Complete Setup” and “Kit Only Package”, then go to step 4

for installation.

Installation and Test Operation

FM0+ S6E1C-Series Starter Kit Guide, Doc. # 002-10542 Rev. *D 10

3. Click Install FM0-64L-S6E1C3 to start the kit installation, shown as Figure 2-1.

Figure 2-1: Kit Installation Window

4. Select the folder in which you want to install this package or use the default folder.

5. When you click Next, the FM0+ S6E1C-Series Starter Kit installer automatically installs the

required software, if it is not present on your PC. Following are the required softwares and

drivers:

FM Universal Peripheral Driver Library (PDL)

Serial Port Viewer

FLASH USB DIRECT Programmer

FLASH MCU Programmer

CMSIS-DAP driver

Inhaltsverzeichnis

Andere Cypress Semiconductor Computerhardware Handbücher

Cypress Semiconductor

Cypress Semiconductor CY3215-DK Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY7C1460AV33 Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor HOTLink II CYV15G0104TRB Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY7C130 Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor PSoC CapSense CY8CKIT-031 Handbuch

Cypress Semiconductor

Cypress Semiconductor MoBL CY62157EV30 Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor ISR 37000 CPLD Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY7B991 Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY7C1410JV18 Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY7C1146V18 Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY7C1516AV18 Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY7C1297H Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY8CTMG200 Handbuch

Cypress Semiconductor

Cypress Semiconductor CY7C1471BV33 Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY7C1141V18 Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor Perform STK16C88-3 Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor STK22C48 Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor NoBL CY7C1470BV25 Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY4672 PROC Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY62167EV30 Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor MoBL CY62126EV30 Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY2071A Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor NoBL CY7C1470V33 Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY7C1345G Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung