D-Link DCS-1000 Bedienungsanleitung
DCS-1000
DCS-1000W
Manual
Version 3.2
(10/25/2002)
2
Contents
Package Contents................................................................. 3
Introduction ........................................................................... 4
Hardware Installation ............................................................. 9
Security ............................................................................... 10
Using the Internet Camera as a Security System...................11
Software Installation ............................................................ 15
IPView Application Installation .............................................. 35
IPView - Getting Started ................................................... ...41
Uninstall IPView Application ................................................. 71
Appendix ............................................................................. 73
Technical Specifications ...................................................... 89
Contacting Technical Support .............................................. 91
Warranty and Registration........................................................92
Index...........................................................................................95
3
Contents of Package:
Package Contents
If any of the above items are missing, please contact your reseller.
System Requirements:
Local Area Network: 10Base-T Ethernet or 100Base TX Fast Ethernet
Wireless Local Area Network: IEEE 802.11b Wireless LAN (Wireless Internet
Camera only)
Recommended: PC or Notebook to Access the Internet Camera
Web Configuration
•Java Enabled and Compliant Web Browser
•CPU: Pentium II, 266 MHz or above
•Memory Size: 32 MB (64 MB recommended)
•VGA card resolution: 800x600 or above
•One Internet Camera
•Two External Wireless Antennas (Wireless Internet Camera only)
•One Installation CD-ROM
•One AC power adapter
•One Camera Stand
•One Category 5 Ethernet Cable
4
Introduction
System Requirements (continued):
IPView Configuration
•Windows XP, Me, 2000, 98SSe or 98
•CPU: Pentium II, 350 MHz or above
•Memory Size: 128 MB (256 MB recommended)
•VGA card resolution: 800x600 or above
The Internet Camera connects directly to an Ethernet, Fast Ethernet, or 802.11b (DCS-
1000W only) Network. It is different from the conventional PC Camera because the
Internet Camera is a stand-alone system with a built-in CPU and web server providing a
low cost solution that can transmit high quality video images for monitoring. The Internet
Camera can be accessed remotely, and controlled from any PC/Notebook over the Intranet
or Internet via a web browser. The simple installation procedures and web-based inter-
face offers easy integration to your network application environments coupled with many
applications such as remote monitoring for a cost-effective solution.
Simple to Use
The Internet Camera is a standalone system with built-in CPU requiring no special
hardware or software such as PC frame grabber cards. The Internet Camera supports
both ActiveX mode for Internet Explorer and Java mode for Internet Explorer and
Netscape Navigator. Therefore, all that is required is a computer with a web browser
software such as Internet Explorer 4.0 or above or Netscape 4.0 or above. Just plug
and view the picture from your Internet Camera with a valid IP Address.
Supports a Variety of Platforms
Supporting TCP/IP networking, SMTP e-mail, HTTP and other Internet related
protocols, the Internet Camera can be utilized in a mixed operating system environment
such as Windows, Unix, and Macintosh. It can also be integrated easily into other
Internet/Intranet applications because of its standards based features.
Features & Benefits
5
Wired and Wireless Network Support
The Internet Camera supports both wired and wireless transmission (DCS-1000W only,
the DCS-1000 supports wired transmittion only) providing the advantage of mobility,
flexibility and high-speed of wireless LAN based technology, IEEE 802.11b, to transform
the Internet Camera into a total solution for your network. There are three modes available,
configured from the slide switch on the rear panel:
•LAN (Local Area Network Only)
•LAN/WLAN (Local Area Network and Wireless Local Area Network. Both can
be accessed at the same time) (Wireless Internet Camera only)
•WLAN (Wireless Local Area Network) (Wireless Internet Camera only)
Broad Range of Applications
With today’s high-speed Internet services, the Internet Camera can provide the ideal
solution for live video images over the Intranet and Internet for remote monitoring. The
Internet Camera allows remote access from a web browser for live image viewing and
allows the administrator to manage and control the Internet Camera anywhere and any
time in the world. Apply the Internet Camera to monitor various objects and places such
as homes, offices, banks, hospitals, child-care centers, amusement parks and other
varieties of industrial and public monitoring. The Internet Camera can also be used for
intruder detection, capture still images and video images for archiving and many more
applications.
Connection to External Devices
Supporting auxiliary Input/Output connectors, you can connect the Internet Camera to
a variety of external devices such as IR-sensors, switches and alarm relays. One can
combine with programmable alarming facilities to develop a variety of security applications
that are triggered on alarm-based events. The Internet Camera provides up to two in/out
external devices for connectivity.
Remote Monitoring Utility
Powerful IPView application assigns administrator with a pre-defined user ID and
password who can modify the Internet Camera settings from the remote site via Intranet
or Internet, and upgrade remotely over the network for added convenience. Users are
also allowed to monitor the image, record the image to a hard drive, and take snapshots.
Web Configuration
Applying a standard web browser, administrators can configure and manage the Internet
Camera directly from its own web page via the Intranet or Internet. Up to 64 user names
and passwords are permitted, with privilege setting controlled by the administrator.
6
Connections
Network Cable Connector
The Internet Camera’s rear panel features an RJ-45 connector for connections to 10Base-
T Ethernet cabling or 100Base-TX Fast Ethernet cabling (which should be Category 5
twisted-pair cable). The port supports the NWay protocol, allowing the Internet Camera
to automatically detect or negotiate the transmission speed of the network.
DC Power Connector
The DC power input connector is located on the Internet Camera’s rear panel and is
labeled DC 5V with a single jack socket to supply power to the Internet Camera.
Reset Button
Reset will be initiated when the reset button is pressed once and Power LED begins to
flash.
Factory Reset will be initiated when the reset button is pressed continuously for three
seconds or when Power LED begins to light up. Release the reset button and the Power
LED will begin to flash indicating that the Internet Camera’s settings are reverting back
to the factory settings. When factory reset is completed the Internet Camera will be set
to default on channel 11 and EES-ID is set as “NULL String.” (This default setting will let
the Internet Camera connect to ANY access point on the infrastructure network.) The IP
address will also return to the default setting of 192.168.0.20.
Antenna Connectors
(DCS-1000W only)
Ethernet Cable
Connector
Reset Button
Slide Switch
(DCS-1000W only)
DC Power Connector
I/O Connector
7
Slide Switch (DCS-1000W only)
The slide switch permit user’s to determine the type of network
communication media for the Internet Camera and is positioned on the rear
panel. The three settings are as follows:
•LAN (Local Area Network Only)
•LAN/WLAN (Local Area Network and Wireless Local Area Network.
Both can be accessed at the same time.)
•WLAN (Wireless Local Area Network Only)
I/O Connector
There are four I/O connectors, two for input and two for output situated on the
rear panel. The I/O connectors provide the physical interface to send and receive
digital signals to a variety of external alarm devices. Please refer to the User’s
Guide appendix for detailed information.
Antenna Connector
There are two SMA type antenna connectors located at the rear panel of the Internet
Camera providing connection for two high sensitivity antenna included with the device.
Connections (continued)
Bottom Panel
Bracket Cavity
Bracket Cavity
Located on the bottom panel of the Internet Camera, the bracket cavity is used to
connect the camera stand onto the Internet Camera by attaching the screw head on
the camera stand into the mounting cavity of the Internet Camera.
8
LEDS
LED stands for Light-Emitting Diode.
Power LED
The Power LED is positioned on the right side of the Internet Camera lens
while facing the Internet Camera. Steady blue confirms that the Internet Camera
is powered on.
Note:
There are three settings for the Power LED to control the light illumination for
monitoring purposes: Normal / Off / Dummy. Please refer to the Web
Configuration section for detailed information and usage.
LAN/WLAN LED (Wireless Internet Camera only)
The LAN/WLAN LED is positioned on the right side of the Internet Camera’s,
lens while facing the Internet Camera. It is located to the right of the Power
LED
Steady orange confirms good connection to the LAN or WLAN.
Dependent on the data traffic the LED will begin to flash to indicate that the
Internet Camera is receiving/transceiving from/to the LAN or WLAN network.
Note:
There are three settings for the LAN/WLAN LED to control the light illumination
for monitoring purposes: Normal / Off / Dummy. Please refer to the Web
Configuration section for detailed information and usage.
9
1. Attach Wireless Antenna (Wireless
Internet Camera only)
From the rear panel of the Internet Camera,
screw the 2 external antennas that came with
DCS-1000W into the antenna connector.
2. Configure Network Communication
(Wireless Internet Camera only)
From the rear panel of the Internet Camera select
the desired network communication for the Internet
Camera from the Slide Switch. Position the Slide
Switch to the setting required for either LAN or LAN/
WLAN (Wireless Internet Camera only) position.
Please refer to the Physical Description section
for detailed information.
3. Connect an Ethernet cable
Connect an Ethernet cable to the network
cable connector located on the Internet
Camera’s rear panel and attach it to the
network.
4. Attach the external power supply
Attach the external power supply to the DC power
input connector located on the Internet Camera’s
rear panel and labeled DC 5V and connect it to
your local power supply.
Note:
The LED indicator labeled Power will illuminate to
indicate a proper connection to the power supply.
Hardware Installation
10
The Internet Camera comes with a camera
stand with a swivel ball screw head that
can be attached to the Internet Camera
bottom bracket cavity. Attach the camera
stand to the Internet Camera and station it
for your application. There are three holes
located in the base of the camera stand
allowing the Internet Camera to be mounted
on the ceiling or any wall securely.
Connecting the Internet Camera to the Camera Stand
Security
To ensure the highest security and prevent unauthorized usage of the Internet
Camera, the Administrator has the exclusive privilege to access the System
Administration setting to allow users the security level of entry and authorize
privileges for all users. The Internet Camera supports multi-level password
protection/access to the Internet Camera that can be restricted to defined
users who have a “User Name” and “User Password” which is assigned by
the Administrator.
The administrator can release a public user name and password so that when
remote users access the Internet Camera they will have the right to view the
image transmitted by the Internet Camera.
Note:
When the Internet Camera is used for the first time it is highly recommended
that the Administrator set the “Admin ID” and “Admin Password” to constrain
user access to the Internet Camera since the Default settings are Null String
(no password). Once the ID and Password are defined only the Administrator
has the access to the management of the Internet Camera. This procedure
should be done as soon as possible since the security features of the Internet
Camera will not be enabled until the “Admin ID” and “Admin Password” is
defined.
Andere Handbücher für DCS-1000
6
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere D-Link IP-Kamera Handbücher
D-Link
D-Link WIRELESS G DCS-950G Bedienungsanleitung
D-Link
D-Link SECURICAM Network DCS-900W Bedienungsanleitung
D-Link
D-Link SECURICAM NETWORK DCS-5300 Bedienungsanleitung
D-Link
D-Link DCS-6620G - Network Camera Bedienungsanleitung
D-Link
D-Link DCS-6620G - Network Camera Bedienungsanleitung
D-Link
D-Link SECURICAM Network DCS-900 Bedienungsanleitung
D-Link
D-Link SECURICAM Network DCS-2120 Bedienungsanleitung
D-Link
D-Link SECURICAM Network DCS-2100+ Bedienungsanleitung
D-Link
D-Link DCS-1110 - Network Camera Bedienungsanleitung
D-Link
D-Link DCS-2121 - SECURICAM Network Camera Bedienungsanleitung
D-Link
D-Link WIRELESS G DCS-950G Bedienungsanleitung
D-Link
D-Link WIRELESS G DCS-950G Bedienungsanleitung
D-Link
D-Link Securicam Network DCS-2000 Bedienungsanleitung
D-Link
D-Link DCS-825L Bedienungsanleitung
D-Link
D-Link DCS-2330L Bedienungsanleitung
D-Link
D-Link SECURICAM Network DCS-950 Bedienungsanleitung
D-Link
D-Link WIRELESS G DCS-950G Bedienungsanleitung
D-Link
D-Link SECURICAM Network DCS-2120 Bedienungsanleitung
D-Link
D-Link DCS-942L Bedienerhandbuch
D-Link
D-Link SECURICAM Network DCS-6620 Bedienungsanleitung
