D-Link SECURICAM Network DCS-2120 Bedienungsanleitung
Wireless G USB 2.0 Adapter
Wireless Internet Camera
with 3G Mobile Video
2D-Link DCS-2120 Quick Install Guide
System Requirements
• Windows®2000 or XP
• At least 128MB of memory (256MB recommended)
• A wireless (802.11b or 802.11g) or Ethernet network
• Internet Explorer 6.x or higher Internet Web Browser
• VGA card resolution: 800x600 or above
• CPU: Pentium 4 1.3GHz or above processor (Pentium 4 2.4GHz
processor or higher with 512MB memory and a 32MB video
card is required for multiple camera viewing and recording in IP
surveillance program)
Manual and Software on CD
Package Contents
D-Link DCS-2120
Wireless Internet Camera
with 3G Mobile Video Support
System Requirements
If any of the above items are missing, please contact your reseller.
Note: If using multiple cameras for viewing/recording, the minimum
requirements are a 2GHz or above CPU with 512MB memory and a
32MB video card.
Antenna CAT5 Ethernet Cable Power Adapter
3 D-Link DCS-2120 Quick Install Guide
Hardware Overview
Hardware Overview
LED
As soon as the power adapter is connected to the camera, the power LED will
flash red and blue several times, indicating that the DCS-2120 is conducting
a self-test. Upon passing the self-test, the LED will turn blue indicating a good
connection to the Ethernet port, or red indicating that no connection has been
made.
Antenna Connector
One antenna is included with the DCS-2120. It
is fastened onto the antenna connector located
on the side panel, which is used to provide a
connection with a wireless network.
4D-Link DCS-2120 Quick Install Guide
Hardware Overview
Ethernet Cable Connector
The DCS-2120 features an RJ-45 connector for connections to 10Base-T
Ethernet cabling or 100Base-TX Fast Ethernet cabling. The port supports the
NWay protocol, allowing the DCS-2120 to automatically detect or negotiate the
transmission speed of the network.
Reset Button
Reset is initiated when the reset button is pressed
once and the Power LED begins to flash. Factory
Reset will be initiated when the reset button is
pressed continuously for 30 seconds. Release
the reset button and the Power LED will begin to
flash, indicating that the DCS-2120’s settings are
restored to factory settings.
DC Power Connector
The DC Power input connector is
labeled DC 5V with a single jack socket
to supply power to the DCS-2120.
5 D-Link DCS-2120 Quick Install Guide
Hardware Installation
Connect an Ethernet cable to the
Ethernet connector located on the
Internet Camera’s bottom panel and
attach it to the network.
Note: It is required that an Ethernet
cable is used during initial setup. Once
your wireless configuration is set, you
may disconnect the Ethernet cable and
begin communicating wirelessly with
your DCS-2120.
Attach the external power supply to the
DC power input connector located on the
Internet Camera’s bottom panel (labeled
DC 5V 2A) and connect it to an AC power
outlet.
The LED will flash red and blue when you first power on the unit.
The LED will not turn blue until the camera has received a network
IP address.
Hardware Installation
6D-Link DCS-2120 Quick Install Guide
Software Installation
Turn on the computer and Insert the D-Link DCS-2120 Driver CD into the
CD-ROM drive.The step-by-step instructions are shown in Windows®
XP, and are similar in other Windows®operating systems.
If the CD Autorun function does not automatically start on your
computer, click Windows® Start > Run. In the Run command box
type “D:\DCS2120.exe”, where D: represents the drive letter of your
CD-ROM. If it does start, proceed to the next screen.
The InstallShieldWizard window
will appear.
Software Installation
Click Installation Wizard
Click Next
7 D-Link DCS-2120 Quick Install Guide
Software Installation
By default the program will be
installed to: C:\Program Files\
D-Link\Installation Wizard, where
C: represents the drive letter of
your hard drive.
To install to a different location,
click Browse and specify the
location.
Specify a Program Folder.
Setup is complete.
Click Next
Click Next
Click Finish
8D-Link DCS-2120 Quick Install Guide
Configuration
The D-Link DCS-2120 uses the Installation Wizard as the management
software. The wizard provides the user an easy interface to change
any settings related to the Wireless Internet Camera. Clicking on the
Installation Wizard icon will start the wizard.
The Installation Wizard will
appear and show the MAC
address of the DCS-2120 and an
IP Address. If you have a DHCP*
server on your network, there will
be a valid IP Address displayed
here, indicated by a “Yes” under
the assigned column.
*A DHCP server is a device that
supplies IP Addresses to its
clients, which are on the same
network.
D-Link Installation Wizard
This section will show you how to configure your new D-Link Wireless
Internet Camera using the D-Link Installation Wizard.
Configuration
9 D-Link DCS-2120 Quick Install Guide
Configuration
If the Installation Wizard does not detect
any devices, you will need to reset the cam-
era. Reset is initiated when the reset button
is pressed once and the Power LED begins
to flash. Factory Reset will be initiated when
the reset button is pressed continuously for
30 seconds. Release the reset button and
the Power LED will begin to flash, indicating
that the DCS-2120’s settings are restored
to factory settings.
Click Search to refresh the list
of cameras.
10D-Link DCS-2120 Quick Install Guide
Configuration
Once the camera appears, select the camera by placing a check
mark in the box.
Enter an administrative password in the Admin password and Confirm
password fields.
Note: For details on the Date/Time
Settings, please refer to the Manual
on the CD-ROM.
Click Next
Click Setup
Andere Handbücher für SECURICAM Network DCS-2120
4
Inhaltsverzeichnis
Andere D-Link IP-Kamera Handbücher
D-Link
D-Link DCS-933L Cloud Camera 1150 Bedienungsanleitung
D-Link
D-Link DCS-2530L Bedienungsanleitung
D-Link
D-Link DCS-1000 Bedienungsanleitung
D-Link
D-Link DCS-1000 Bedienungsanleitung
D-Link
D-Link SECURICAM Network DCS-2100 Bedienungsanleitung
D-Link
D-Link DCS-960L Bedienungsanleitung
D-Link
D-Link SECURICAM Network DCS-6620 Bedienungsanleitung
D-Link
D-Link DCS-6620G - Network Camera Bedienungsanleitung
D-Link
D-Link SECURICAM Network DCS-5300W Bedienungsanleitung
D-Link
D-Link DCS-1000 Bedienungsanleitung
D-Link
D-Link Cloud Camera 2330L Bedienungsanleitung
D-Link
D-Link WIRELESS G DCS-950G Bedienungsanleitung
D-Link
D-Link DCS-3420 Bedienungsanleitung
D-Link
D-Link SECURICAM Network DCS-5300G Bedienungsanleitung
D-Link
D-Link DCS-2332L Installations- und Betriebshandbuch
D-Link
D-Link DCS-6620G - Network Camera Bedienungsanleitung
D-Link
D-Link DCS-1130 - mydlink-enabled Wireless N Network... Bedienungsanleitung
D-Link
D-Link DCS-942L Bedienerhandbuch
D-Link
D-Link SECURICAM Network DCS-950 Bedienungsanleitung
D-Link
D-Link DCS-2310L Bedienungsanleitung
